Thermal, Electrical and Physical Properties of Recycled Copper Filled Epoxy Composites

2012 ◽  
Vol 620 ◽  
pp. 208-212
Author(s):  
Mohamd Nur Fuadi Pargi ◽  
Pei Leng Teh ◽  
Salmah Husseinsyah ◽  
Cheow Keat Yeoh
Keyword(s):  
Electrical Conductivity ◽  
Thermal Expansion ◽  
Physical Properties ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
Coefficient Of Thermal Expansion ◽  
Filler Loading ◽  
Epoxy Composites ◽  
Milling Machine

The effect of recycled copper filled epoxy composites on thermal, electrical and physical properties were investigated. The recycled copper was collected as a waste from the milling machine. The recycled copper filled epoxy composite was mixed using mechanical stirrer. The effect of volume fraction of recycled copper of the epoxy composites were studied based on the coefficient of thermal expansion (CTE), electrical conductivity hardness and density. Incorporation of recycled copper has decreased the CTE of the composites. The electrical conductivity, hardness and density of the composites increased with increasing of volume fraction and filler loading.

Electrical Conductivity and Micro Hardness of Synthetic and Natural Graphite Epoxy Composite

2010 ◽  
Vol 447-448 ◽  
pp. 614-618 ◽  
Author(s):  
Hendra Suherman ◽  
Jaafar Sahari ◽  
Abu Bakar Sulong
Keyword(s):  
Electrical Conductivity ◽  
Epoxy Resin ◽  
High Speed ◽  
Epoxy Composite ◽  
Filler Loading ◽  
Epoxy Composites ◽  
Micro Hardness ◽  
Electron Microscopic ◽  
Natural Graphite ◽  
Weight Percentage

This study investigates the electrical conductivity and micro hardness of synthetic and natural graphite epoxy composite. Graphite used on this study is synthetic graphite (SG) and natural graphite (NG) with particle size 44m and 30m, respectively. Different graphite concentrations (50 ~ 80 wt.%) were added into the epoxy resin. The dispersion of graphite in epoxy resin was conducted by high speed mixer through mechanical shearing mechanism, its graphite epoxy suspension was poured into the mold and compression molding was conducted for fabrication of graphite epoxy composites. Electrical conductivity was measured by the four point probe. Microscopic analyses conducted on fracture surface use scanning electron microscopic. Results reveal that non conductive epoxy polymer becomes conductor as addition of graphite. Electrical conductivity of NG higher than SG at the same weight percentage (Wt. %) of conducting filler loading. The highest loading concentration, it exhibited values 12.6 S/cm and 7 S/cm at (80 Wt. %). Hardness property of epoxy composites of both type of graphite increase continuously and reached peak at 60 wt% for NG and 70 wt % for SG, while more addition decreased it.

Comparison study of carbon black (CB) used as conductive filler in epoxy and polymethylmethacrylate (PMMA)

2016 ◽  
Vol 36 (4) ◽  
pp. 391-398 ◽  
Author(s):  
Jin-Luen Phua ◽  
Pei-Leng Teh ◽  
Supri Abdul Ghani ◽  
Cheow-Keat Yeoh
Keyword(s):  
Thermal Stability ◽  
Electrical Conductivity ◽  
Fracture Toughness ◽  
Thermal Expansion ◽  
Carbon Black ◽  
Coefficient Of Thermal Expansion ◽  
Conductive Filler ◽  
Filler Loading ◽  
Comparison Study ◽  
Thermoset Epoxy

Abstract A comparison study between carbon black (CB) filled thermoset (epoxy) and thermoplastic, polymethylmethacrylate (PMMA), was done in this research. CB was introduced as the conductive filler in epoxy and PMMA at different filler loading, which ranged from 5 vol.% to 20 vol.%. The physical, mechanical, electrical and thermal stability properties were investigated. The incorporation of CB into both epoxy and PMMA increased the density, improved the thermal stability and electrical conductivity of the composites, reduced the coefficient of thermal expansion and weakened the flexural and fracture toughness properties of the composites.

NILO ALLOY 36

Alloy Digest ◽  
1987 ◽  
Vol 36 (8) ◽  
Keyword(s):  
Thermal Expansion ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Surface Treatment ◽  
Constant Coefficient ◽  
Coefficient Of Thermal Expansion ◽  
Heat Treating ◽  
Temperature Performance ◽  
Iron Nickel

Abstract NILO alloy 36 is a binary iron-nickel alloy having a very low and essentially constant coefficient of thermal expansion at atmospheric temperatures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Fe-79. Producer or source: Inco Alloys International Inc..

UNISPAN LR35

Alloy Digest ◽  
1971 ◽  
Vol 20 (1) ◽  
Keyword(s):  
Thermal Expansion ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Coefficient Of Thermal Expansion ◽  
Heat Treating ◽  
Temperature Performance ◽  
Operational Level

Abstract UNISPAN LR35 offers the lowest coefficient of thermal expansion of any alloy now available. It is a low residual modification of UNISPAN 36 for fully achieving the demanding operational level of precision equipment. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and surface treatment. Filing Code: Fe-46. Producer or source: Cyclops Corporation.

DELTALLOY 4032

Alloy Digest ◽  
1998 ◽  
Vol 47 (4) ◽  
Keyword(s):  
Wear Resistance ◽  
Thermal Expansion ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Surface Finish ◽  
Coefficient Of Thermal Expansion ◽  
Single Point ◽  
High Strength ◽  
Corrosion And Wear

Abstract Deltalloy 4032 has good machinability and drilling characteristics when using single-point or multispindle screw machines and an excellent surface finish using polycrystalline or carbide tooling. The alloy demonstrates superior wear resistance and may eliminate the need for hard coat anodizing. Deltalloy 4032 is characterized by high strength and a low coefficient of thermal expansion. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on corrosion and wear resistance as well as machining and surface treatment. Filing Code: AL-347. Producer or source: ALCOA Wire, Rod & Bar Division.

RED X-20

Alloy Digest ◽  
1960 ◽  
Vol 9 (2) ◽  
Keyword(s):  
Wear Resistance ◽  
Thermal Expansion ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Coefficient Of Thermal Expansion ◽  
Heat Treating ◽  
Aluminum Silicon Alloy ◽  
Temperature Performance

Abstract RED X-20 is a heat treatable hypereutectic aluminum-silicon alloy with excellent wear resistance and a very low coefficient of thermal expansion. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Al-89. Producer or source: Apex Smelting Company.

AA 4032

Alloy Digest ◽  
1990 ◽  
Vol 39 (7) ◽  
Keyword(s):  
Thermal Expansion ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Coefficient Of Thermal Expansion ◽  
Heat Treating ◽  
Temperature Performance

Abstract AA 4032 has a comparatively low coefficient of thermal expansion and good forgeability. The alloy takes on an attractive dark gray appearance when anodized which may be desirable in architectural applications. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fatigue. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Al-305. Producer or source: Various aluminum companies.

Effect of Interconnectivity of Nickel on Electrical and Thermal Properties of Alumina-Ni Interpenetrating Phase Composite

2011 ◽  
Vol 239-242 ◽  
pp. 2679-2682 ◽  
Author(s):  
Rub Nawaz Shahid ◽  
Bin Awais Hasan ◽  
Fahad Ali ◽  
Naeem Ul Haq Tariq
Keyword(s):  
Electrical Conductivity ◽  
Thermal Expansion ◽  
Thermal Properties ◽  
Impedance Spectroscopy ◽  
Electron Spectroscopy ◽  
Coefficient Of Thermal Expansion ◽  
Optimal Combination ◽  
Percolation Limit ◽  
Scanning Electron

In this work percolation range for Al2O3-Ni interpenetrating phase composite (IPC) was studied to find the optimal combination of electrical conductivity and coefficient of thermal expansion (CTE). The impedance spectroscopy and scanning electron spectroscopy were used to study the percolation limit.

Experimental Investigation on Volume Fraction of Mechanical and Physical Properties of Flax and Bamboo Fibers Reinforced Hybrid Epoxy Composites

2017 ◽  
Vol 25 (3) ◽  
pp. 229-236 ◽  
Author(s):  
S. Sathish ◽  
K. Kumaresan ◽  
L. Prabhu ◽  
N. Vigneshkumar
Keyword(s):  
Physical Properties ◽  
Epoxy Resin ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Sem Analysis ◽  
Epoxy Composites ◽  
Resin Matrix ◽  
Void Content ◽  
Mechanical And Physical Properties ◽  
Bamboo Fibers

The aim of this paper is to study the effect of volume fraction on mechanical and physical properties such as tensile, flexural, impact, interlaminar shear strength, void content and water absorption of flax and bamboo fibers reinforced hybrid epoxy composites. Flax and bamboo fibers reinforced epoxy resin matrix hybrid composites have been fabricated by compression molding techniques. The hybrid composites were fabricated with different volume fraction of fibers. SEM analysis on the hybrid composite materials was performed to analyze the bonding behavior of materials and internal structure of the fractured surfaces. The effect of chemical treatment of flax and bamboo fibers was verified by FTIR analysis. The results showed that the tensile, impact, flexural and ILSS are maximum for 40:0 (flax: bamboo) hybrid composites. The void content decreased for 20:20 (flax:bamboo) composites due to tightly packed flax fiber and more compatibility towards epoxy resin.

Sign in / Sign up

Export Citation Format

Share Document