Structure Characterization of Sintered CaO-Al2O3-SiO2 Glass-Ceramic Reinforced with Spodumene

2013 ◽  
Vol 834-836 ◽  
pp. 309-314
Author(s):  
Zi Fan Xiao ◽  
Jin Shu Cheng ◽  
Jun Xie
Keyword(s):  
Glass Ceramic ◽  
Energy Dispersive Spectrometry ◽  
Crystal Size ◽  
Bending Strength ◽  
Glass Ceramics ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
Crystalline Phases ◽  
X Ray

A glass-ceramic belonging to the CaO-Al2O3-SiO2(CAS) system with different composition of spodumene and doping the Li2O with amount between 0~2.5 % (mass fraction) were prepared by onestage heat treatment, under sintering and crystallization temperature at 1120 °C for two hours. In this paper, differential thermal analysis, X-ray diffraction, scanning electron microscopy, energy dispersive spectrometry and bending strength test were employed to investigate the microstructure and properties of all samples. β-wollastonite crystals were identified as the major crystalline phases, and increasing Li2O was found to be benefit for the crystallization and tiny crystalline phases remelting, resulting in the content of major crystalline phases increased first and then decreased with increasing the expense of spodumene. Meanwhile, the crystal size can be positively related with the content of Li2O. The preferable admixed dosage of spodumene can be obtained, besides the strength of glass-ceramics can be more than 90 MPa.

Physical-Mechanical Behaviour of a LZS Glass-Ceramic

2014 ◽  
Vol 775-776 ◽  
pp. 599-603 ◽  
Author(s):  
Jaime Domingos Teixeira ◽  
Manuel Alfredo Pereira ◽  
Lourival Boehs ◽  
Cristina Siligardi ◽  
Vicente Cantavella ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Glass Ceramic ◽  
Modulus Of Elasticity ◽  
Bending Strength ◽  
Glass Ceramics ◽  
Physical And Mechanical Properties ◽  
Maximum Hardness ◽  
X Ray Diffraction ◽  
X Ray

Physical and mechanical properties of a glass-ceramic belonging to the LZS (Li2O-SiO2-ZrO2) system were investigated by dilatometric analysis, differential thermal analysis, X-ray diffraction and measurements of density, hardness, bending strength, modulus of elasticity and fracture toughness. The obtained glass-ceramics showed ZrSiO4 and Li2Si2O5 as main crystalline phases, relative densities between 84 and 99%, maximum hardness, bending strength, modulus of elasticity and toughness of 8±0.5 GPa, 214±20 MPa, 115±0.42 GPa and 3.65±0.21 MPa.m1/2, respectively.

scholarly journals Bone bonding ability of some borate bio-glasses and their corresponding glass-ceramic derivatives

2012 ◽  
Vol 6 (4) ◽  
pp. 183-192 ◽  
Author(s):  
Fatma Margha ◽  
Amr Abdelghany
Keyword(s):  
Heat Treatment ◽  
Fourier Transform ◽  
Glass Ceramic ◽  
Glass Composition ◽  
Glass Ceramics ◽  
Soda Lime ◽  
Phosphate Solution ◽  
Borate Glasses ◽  
X Ray Diffraction ◽  
X Ray

Ternary borate glasses from the system Na2O?CaO?B2O3 together with soda-lime-borate samples containing 5 wt.% of MgO, Al2O3, SiO2 or P2O5 were prepared. The obtained glasses were converted to their glass-ceramic derivatives by controlled heat treatment. X-ray diffraction was employed to investigate the separated crys?talline phases in glass-ceramics after heat treatment of the glassy samples. The glasses and corresponding glass-ceramics after immersion in water or diluted phosphate solution for extended times were characterized by the grain method (adopted by several authors and recommended by ASTM) and Fourier-transform infrared spectra to justify the formation of hydroxyapatite as an indication of the bone bonding ability. The influence of glass composition on bioactivity potential was discussed too.

HIPed Tailored Pyrochlore-Rich Glass-Ceramic Waste Forms for the Immobilization of Nuclear Waste

2008 ◽  
Vol 1124 ◽  
Author(s):  
Melody Lyn Carter ◽  
Hui Li ◽  
Yingjie Zhang ◽  
Andrew L Gillen ◽  
Eric R Vance
Keyword(s):  
Nuclear Waste ◽  
Glass Ceramic ◽  
Glass Ceramics ◽  
Spectroscopic Characterization ◽  
Chemical Durability ◽  
Intermediate Level ◽  
Crystalline Phases ◽  
Waste Forms ◽  
Ceramic Samples

AbstractHot isostatically pressed (HIPed) glass-ceramics for the immobilization of uranium-rich intermediate-level wastes and Hanford K-basin sludges were designed. These were based on pyrochlore-structured Ca(1-x)U(1+y)Ti2O7 in glass, together with minor crystalline phases. Detailed microstructural, diffraction and spectroscopic characterization of selected glass-ceramic samples has been performed, and chemical durability is adequate, as measured by both MCC-1 and PCT-B leach tests.

scholarly journals Synthesis of Silver Nanoparticles Using Muntingia Calabura L. Leaf Extract as Bioreductor and Applied as Glucose Nanosensor

2018 ◽  
Vol 34 (6) ◽  
pp. 3088-3094 ◽  
Author(s):  
Abdul Wahid Wahab ◽  
Abdul Karim ◽  
Nursiah La Nafie ◽  
Nurafni Nurafni ◽  
I. Wayan Sutapa
Keyword(s):  
Particle Size ◽  
Silver Nanoparticles ◽  
Reduction Method ◽  
Measurement Range ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Particle Size Analyzer ◽  
Muntingia Calabura

Silver nanoparticles have been synthesized by reduction method using extract of Muntingia calabura L. leaf a bioreductor. The process of silver nanoparticles formation was monitored by UV-Vis method. The results showed that the absorbance values increased according to the increase of reaction time. Maximum absorption of silver nanoparticle was obtained at a wavelength of 41-421 nm. The size of silver nanoparticles was determined using a PSA (Particle Size Analyzer) with a particle size distribution of 97.04 nm. The functional groups compound that contribute in the synthesis was analyzed using Fourier Transform Infrared Spectroscopy (FTIR). Morphology of the silver nanoparticles was observed by an Scanning Electron Microscope instrument and the structure characterization of the compounds were analyzed using X-Ray Diffraction. The glucose nanosensor based on silver nanoparticles have the measurement range of 1 mM - 4 mM with the regretion (R2) is 0,9516, the detection limit of sensor is 3,2595 mM, the sensitivity of sensor is 2,0794 A. mM-1. mM-2.

scholarly journals Effects of Sintering Temperature Variation on Synthesis of Glass-Ceramic Phosphor Using Rice Husk Ash as Silica Source

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5413
Author(s):  
Rabiatul Adawiyah Abdul Wahab ◽  
Mohd Hafiz Mohd Zaid ◽  
Sidek Hj. Ab Aziz ◽  
Khamirul Amin Matori ◽  
Yap Wing Fen ◽  
...  
Keyword(s):  
Rice Husk ◽  
Glass Ceramic ◽  
Rice Husk Ash ◽  
Glass Ceramics ◽  
Xrd Analysis ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Silica Source ◽  
Quenching Method

In this study, the authors attempted to propose the very first study on fabrication and characterization of zinc-boro-silicate (ZBS) glass-ceramics derived from the ternary zinc-boro-silicate (ZnO)0.65(B2O3)0.15(RHA)0.2 glass system through a conventional melt-quenching method by incorporating rice husk ash (RHA) as the silica (SiO2) source, followed by a sintering process. Optimization of sintering condition has densified the sintered samples while embedded beta willemite (β-Zn2SiO4) and alpha willemite (α-Zn2SiO4) were proven in X-ray diffraction (XRD) analysis. Field emission scanning electron microscopy (FESEM) has shown the distribution of willemite crystals in rhombohedral shape crystals and successfully form closely-packed grains due to intense crystallization. The photoluminescence (PL) spectra of all sintered ZBS glasses presented various emission peaks at 425, 463, 487, 531, and 643 nm corresponded to violet, blue, green, and red emission, respectively. The correlation between the densification, phase transformation, microstructure, and photoluminescence of Zn2SiO4 glass-ceramic phosphor is discussed in detail.

Neodymium Incorporation in Zirconolite-Based Glass-Ceramics

2000 ◽  
Vol 663 ◽  
Author(s):  
P. Loiseau ◽  
D. Caurant ◽  
N. Baffier ◽  
C. Fillet
Keyword(s):  
Heat Treatment ◽  
Glass Ceramics ◽  
Fission Products ◽  
Treatment Temperature ◽  
Spent Fuel ◽  
X Ray Diffraction ◽  
Parent Glass ◽  
X Ray ◽  
Spin Resonance

ABSTRACTThe investigations on enhanced reprocessing of nuclear spent fuel, and notably on separating the long-lived minor actinides, such as Am and Cm, from the other fission products have led to the development of highly durable specific matrices such as glass-ceramics for their immobilization. This study deals with the characterization of zirconolite (CaZrTi2O7) based glass-ceramics synthesized by devitrification of an aluminosilicate parent glass. Trivalent actinide ions were simulated by neodymium, which is a paramagnetic local probe. Glass-ceramics with Nd2O3 contents ranging from 0 to 10 weight % were prepared by heat treatment of a parent glass at two different growth temperatures: 1050° and 1200°C. X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and electron spin resonance (ESR) measurements clearly indicate that Nd3+ ions are partly incorporated in zirconolite crystals formed in the bulk of the glass-ceramic samples. The amount of neodymium in the crystalline phase was estimated using ESR results and was found to decrease with increasing either heat treatment temperature or total Nd2O3 content.

MgO-Al2O3-SiO2 Glass-Ceramic Prepared by Sol-Gel Method

2010 ◽  
Vol 92 ◽  
pp. 131-137 ◽  
Author(s):  
Qiu Hua Yuan ◽  
Pei Xin Zhang ◽  
Li Gao ◽  
Hai Lin Peng ◽  
Xiang Zhong Ren ◽  
...  
Keyword(s):  
Glass Ceramic ◽  
Crystallization Behavior ◽  
Glass Powder ◽  
Sol Gel ◽  
Glass Ceramics ◽  
Green Body ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Sio2 Glass ◽  
X Ray

The crystallization behavior of MgO-Al2O3-SiO2 glass-ceramics by sol-gel technology was investigated by using x-ray diffraction (XRD), differential thermal analysis (DTA), Scanning electron microscopy (SEM). The results showed that: (1)α-cordierite phase was precipitated when the green body was calcined at 1050°C, and α-cordierite of high purity and stability could be formed at 1100°C; (2) Adding an appropriate amount of low melting point glass powder into the green body may provide liquid-phase environment during the sintering process, which will help enhance the tightness density of glass-ceramic, and thus improve its flexural strength.

Synthesis and Characterization of Zinc Doped Hydroxyapatite for Bone Substitute Applications

2014 ◽  
Vol 660 ◽  
pp. 942-946
Author(s):  
Mohamad Firdaus Abdul Wahid ◽  
C.M. Mardziah ◽  
Koay Mei Hyie ◽  
N.R. Nik Roselina
Keyword(s):  
Crystal Size ◽  
Diffraction Method ◽  
Lattice Parameters ◽  
Phase Changes ◽  
Precipitation Method ◽  
Zinc Ions ◽  
Crystal Shape ◽  
X Ray Diffraction ◽  
X Ray

Hydroxyapatite was prepared by using precipitation method. The substitution of zinc ions in hydroxyapatite structure was studied by several characterization techniques. Several concentration of zinc ions were substituted into hydroxyapatite. Characterization technique such as X-ray diffraction method was used to study the phase changes and the lattice parameters with the addition of zinc. Field emission scanning electron microscopy was used to examine the influence of zinc on the crystal size and the morphology of the as-synthesized powders. Based on X-ray diffraction result, the addition of zinc affects the lattice parameters and phase. The result showed that zinc ions were substituted in the structure. As zinc substitution increased, the lattice parameters a and c decreased. The crystal shape of hydroxyapatite without zinc ions was regular shapes while hydroxyapatite with zinc ions was irregular and also tends to agglomerates with single particle was calculated about 28 - 34 nm .

Hydrothermal Synthesis and Structure Characterization of a Bi-Capped Keggin Heteropoly Molybdovanadated Derivative

2014 ◽  
Vol 1004-1005 ◽  
pp. 542-545
Author(s):  
Ya Bing Liu ◽  
Li Guang Xiao
Keyword(s):  
Crystal Structure ◽  
Hydrogen Bonding ◽  
Building Blocks ◽  
Crystal Structure Analysis ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hydrogen Bonding Interactions ◽  
Supramolecular Networks

A new bi-capped Keggin heteropoly molybdovanadated derivative, [Co (en)3]2[SiMo8V6O42]∙6H2O (1) (en = ethylendiamine) has been hydrothermally synthesized and structurally characterized by the elemental analysis, IR, XPS and single crystal X-ray diffraction. The crystal structure analysis reveals that compound 1 consists of [Co (en)3]2+transition metal coordination fragment and the [SiMo8V6O42]4-building blocks, which are linked together via hydrogen-bonding interactions to form a new 3-D supramolecular networks.

Crystallization and Mechanical Properties of Glass-Ceramic from Silicon Slag

2014 ◽  
Vol 953-954 ◽  
pp. 1643-1648
Author(s):  
Hang Li ◽  
Li Qiang Liu ◽  
Min Jing ◽  
Zhi Gang Wang ◽  
Zheng Wang ◽  
...  
Keyword(s):  
Glass Ceramic ◽  
Mechanical Performance ◽  
Glass Ceramics ◽  
Ceramic Materials ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Talcum Powder ◽  
X Ray ◽  
Glass Ceramic Materials ◽  
Spherical Grains

The glass-ceramic materials were produced from silicon slag with the addition of talcum powder and TiO2 by melting them in an electrically heated furnace and subsequent heat treatment at various temperatures and time. The microstructure and crystallization behaviors of glass–ceramics have been investigated by differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). With the increase of silicon slag content, the sequent precipitate phase is: krinovite Na (Mg1.9Fe0.1)Cr (SiO)3O, pseudobrookite Fe2TiO5 and anorthite Ca (Al2Si2O8), enstatite ferroan MgFeSi2O6, and albite Na (AlSi3O8). The shape of crystals was spherical grains. The glass–ceramic sample obtained from 70% silicon slag had the excellent mechanical performance including flexural strength of 200.45 MPa and Vickers micro hardness of 909.72 MPa.

Sign in / Sign up

Export Citation Format

Share Document