Influence of Chromium Content and Prior Deformation on the Continuous Cooling Transformation Diagram of Low-Carbon Bainitic Steels

2020 ◽  
Vol 835 ◽  
pp. 58-67
Author(s):  
Mohammed Ali ◽  
Antti J. Kaijalainen ◽  
Jaakko Hannula ◽  
David Porter ◽  
Jukka I. Kömi
Keyword(s):  
Cooling Rate ◽  
Hot Deformation ◽  
Laser Scanning ◽  
Chromium Content ◽  
Bainitic Ferrite ◽  
Granular Bainite ◽  
Low Carbon ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling

The effect of chromium content and prior hot deformation of the austenite on the continuous cooling transformation (CCT) diagram of a newly developed low-carbon bainitic steel has been studied using dilatometer measurements conducted on a Gleeble 3800 simulator with cooling rates ranging from 2-80 °C/s. After austenitization at 1100 °C, specimens were either cooled without strain or given 0.6 strain at 880 °C prior to dilatometer measurements. The resultant microstructures have been studied using laser scanning confocal microscopy, scanning electron microscopy and macrohardness measurements. CCT and deformation continuous cooling transformation (DCCT) diagrams were constructed based on the dilatation curves, final microstructures and hardness values. Depending on the cooling rate, the microstructures of the investigated steels after cooling from the austenite region consist of one or more of the following microstructural components: lath-like upper bainite, i.e. bainitic ferrite (BF), granular bainite (GB), polygonal ferrite (PF) and pearlite (P). The proportion of BF to GB as well as the hardness of the transformation products decreased with decreasing cooling rate. The cooling rate at which PF starts to appear depends on the steel composition. With both undeformed and deformed austenite, increasing the chromium content led to higher hardenability and refinement of the microstructure, promoting the formation of BF and shifting the ferrite start curve to lower cooling rates. Prior hot deformation shifted the transformation curves to shorter times and higher temperatures and led to a reduction in hardness at the low cooling rates through the promotion of ferrite formation.

scholarly journals Influence of Chromium Content on the Microstructure and Mechanical Properties of Thermomechanically Hot-Rolled Low-Carbon Bainitic Steels Containing Niobium

2020 ◽  
Vol 10 (1) ◽  
pp. 344 ◽  
Author(s):  
Mohammed Ali ◽  
Tun Nyo ◽  
Antti Kaijalainen ◽  
Jaakko Hannula ◽  
David Porter ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Cooling Rate ◽  
Chromium Content ◽  
Bainitic Ferrite ◽  
Polygonal Ferrite ◽  
Granular Bainite ◽  
Low Carbon ◽  
Cr Content ◽  
Hot Rolled

The effect of chromium content in the range of 1 wt.%–4 wt.% on the microstructure and mechanical properties of controlled-rolled and direct-quenched 12 mm thick low-carbon (0.04 wt.%) steel plates containing 0.06 wt.% Nb has been studied. In these microalloyed 700 MPa grade steels, the aim was to achieve a robust bainitic microstructure with a yield strength of 700 MPa combined with good tensile ductility and impact toughness. Continuous cooling transformation diagrams of deformed and non-deformed austenite were recorded to study the effect of Cr and hot deformation on the transformation behavior of the investigated steels. Depending on the cooling rate, the microstructures consist of one or more of the following microstructural constituents: bainitic ferrite, granular bainite, polygonal ferrite, and pearlite. The fraction of bainitic ferrite decreases with decreasing cooling rate, giving an increasing fraction of granular bainite and polygonal ferrite and a reduction in the hardness of the transformation products. Polygonal ferrite formation depends mainly on the Cr content and the cooling rate. In both deformed and non-deformed austenite, increasing the Cr content enhances the hardenability and refines the final microstructure, shifting the ferrite start curve to lower cooling rates. Preceding austenite deformation promotes the formation of polygonal ferrite at lower cooling rates, which leads to a decrease in hardness. In hot-rolled and direct-quenched plates, decreasing the Cr content promotes the formation of polygonal ferrite leading to an increase in the impact toughness and elongation but also a loss of yield strength.

Effect of boron on the continuous cooling transformation kinetics in a low carbon advanced ultra-high strength steel (A-UHSS)

2012 ◽  
Vol 1485 ◽  
pp. 83-88 ◽  
Author(s):  
G. Altamirano ◽  
I. Mejía ◽  
A. Hernández-Expósito ◽  
J. M. Cabrera
Keyword(s):  
Research Work ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Low Carbon ◽  
Transformation Kinetics ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Cct Diagrams

ABSTRACTThe aim of the present research work is to investigate the influence of B addition on the phase transformation kinetics under continuous cooling conditions. In order to perform this study, the behavior of two low carbon advanced ultra-high strength steels (A-UHSS) is analyzed during dilatometry tests over the cooling rate range of 0.1-200°C/s. The start and finish points of the austenite transformation are identified from the dilatation curves and then the continuous cooling transformation (CCT) diagrams are constructed. These diagrams are verified by microstructural characterization and Vickers micro-hardness. In general, results revealed that for slower cooling rates (0.1-0.5 °C/s) the present phases are mainly ferritic-pearlitic (F+P) structures. By contrast, a mixture of bainitic-martensitic structures predominates at higher cooling rates (50-200°C/s). On the other hand, CCT diagrams show that B addition delays the decomposition kinetics of austenite to ferrite, thereby promoting the formation of bainitic-martensitic structures. In the case of B microalloyed steel, the CCT curve is displaced to the right, increasing the hardenability. These results are associated with the ability of B atoms to segregate towards austenitic grain boundaries, which reduce the preferential sites for nucleation and development of F+P structures.

scholarly journals Continuous Cooling Transformation of Under-Cooled Austenite of SXQ500/550DZ35 Hydropower Steel

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1562
Author(s):  
Zhenglei Tang ◽  
Ran Guo ◽  
Yang Zhang ◽  
Zhen Liu ◽  
Yuezhang Lu ◽  
...  
Keyword(s):  
Cooling Rate ◽  
Hardness Measurement ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Continuous Cooling Transformation Diagrams ◽  
Transformation Diagrams ◽  
Hot Rolled ◽  
Vickers Hardness Measurement ◽  
Undercooled Austenite

The expansion curves of the continuous cooling transformation of undercooled austenite of SXQ500/550DZ35 hydropower steel at different heating temperatures and cooling rates were measured by use of a DIL805A dilatometer. Combined with metallography and Vickers hardness measurement, the continuous cooling transformation diagrams (CCT) of the studied steel under two different states were determined. The results show that in the first group of tests, after the hot-rolled specimens were austenitized at 920 °C, when the cooling rate was below 1 °C·s−1, the microstructure was composed of ferrite (F), pearlite (P) and bainite (B). With the cooling rates between 1 °C·s−1 and 5 °C·s−1, the microstructure was mainly bainite, and martensite (M) formed as the cooling rate reached 5 °C·s−1. When the cooling rate was up to 10 °C·s−1, the microstructure was completely martensite and the hardness value increased significantly. In the second group of tests, after the hot-rolled specimens were quenched at 920 °C and then heated at an intercritical temperature of 830 °C, in comparison with the first group of tests, and except for additional undissolved ferrites in each cooling rate range, the other microstructure types were basically the same. Due to the existence of undissolved ferrite, the microstructures of the specimens heated at intercritical temperatures were much finer, and the toughness values at low temperatures were better.

Phase transformations in Ti3Al and Ti3Al + Mo aluminides

1991 ◽  
Vol 6 (5) ◽  
pp. 969-986 ◽  
Author(s):  
S. Djanarthany ◽  
C. Servant ◽  
R. Penelle
Keyword(s):  
Phase Transformations ◽  
Cooling Rate ◽  
Titanium Aluminides ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Continuous Cooling Transformation Diagrams ◽  
Transformation Diagrams ◽  
Phase Relationships

We have analyzed the phase relationships in two titanium aluminides containing 3.4 at. % Mo with different aluminum compositions. The alloys were first homogenized in the β field, then cooled continuously at different cooling rates from 80 °C/s to 0.1 °C/s. The continuous cooling transformation diagrams (CCT) show that phase transformations and resulting microstructures are highly dependent on cooling rate. The microstructure consists of ordered α2 (DO19), ordered β0 (B2), and athermal ω (hexagonal) phases. The “tweed microstructure” is observed. The evolution of microhardness was determined as well as the relative partitioning of Al and Mo in (α2', α2) and β0 phases as a function of cooling rate.

Continuous Cooling Transformation Behavior and the Phase Transformation Model in Low Carbon High Strength Sheet Steel

2014 ◽  
Vol 1035 ◽  
pp. 27-35
Author(s):  
Yu Pei ◽  
Zhe Gao ◽  
Yi Liu ◽  
Shi Qian Zhao ◽  
Chang Yu Xu ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Cooling Rate ◽  
Sheet Steel ◽  
High Strength ◽  
Transformation Model ◽  
Phase Variable ◽  
Low Carbon ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Mathematical Equations

Phase transformation of austenite continuous cooling process in low carbon high strength sheet steel has been researched by DIL805 thermal mechanical simulate. The Austenite continuous cooling transformation (CCT) diagram of steel has been determined by dilatometry and metallography. With the increase of cooling rate, ferritic transformation, perlitic transformation, bainite transformation and martensitic transformation have produced in the organization. Mathematical equations of phase transformation point-cooling rate and phase variable-cooling rate have been established and phase transformation model of high fit degree has been gained by regression calculation. The results show that calculated value and experimental value are nearly similar, so the phase transformation model is feasible.

Continuous Cooling Transformation Behavior of a Ti Addition Steel

2014 ◽  
Vol 556-562 ◽  
pp. 480-483
Author(s):  
Chen Zhang ◽  
Guang Xu ◽  
Zhang Wei Hu ◽  
Hai Lin Yang
Keyword(s):  
Phase Transformation ◽  
Solid State ◽  
Cooling Rate ◽  
Transformation Behavior ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Cct Curve ◽  
Solid State Phase Transformation ◽  
Ti Addition

The continuous cooling transformation (CCT) behavior of a Ti attached steel was studied through thermal simulation tests, and the influences of different cooling rates on the microstructure and transformation were investigated. The results show that the microstructure changes with the cooling rate, and the CCT curve of studied steel is plotted, which indicates that the solid-state phase transformation mainly consists of four regions. The CCT diagram made it possible to predict the microstructures of studied steel with different cooling rates.

Continuous Cooling Transformation Behavior of X70 Pipeline Steel

2013 ◽  
Vol 690-693 ◽  
pp. 2205-2209
Author(s):  
Hong Mei Yang
Keyword(s):  
Cooling Rate ◽  
Hot Deformation ◽  
Acicular Ferrite ◽  
Transformation Temperature ◽  
Pipeline Steel ◽  
Continuous Cooling Transformation ◽  
X70 Pipeline Steel ◽  
Continuous Cooling ◽  
Transformation Curve ◽  
Continuous Cooling Transformation Curve

The continuous cooling transformation behaviors were researched on X70 pipeline steel through two pass deformation and non-deformed austenite using Gleeble-3500 thermal mechanical simulator, and static continuous cooling transformation curve and dynamic continuous cooling transformation curve were measured through thermal dilation method and metallographic method. The influence of cooling rate and deformation parameters on microstructure was analyzed. The results show that the hot deformation accelerates the acicular ferrite and polygonal ferrite phase transformation, increases the starting transformation temperature and the finishing transformation temperature significantly, and shifts the CCT curve moving upward to the left side corner. Acicular ferrite is obtained in practice using accelerated cooling rate after deformation Acicular ferrite can be obtained in wider range of cooling rates, and microstructure and island structure is finer through hot deformation.

Dynamic CCT Curve of Hot Deformation Austenite in 55SiCr Steel

2012 ◽  
Vol 548 ◽  
pp. 225-228
Author(s):  
Yong Jun Zhang ◽  
Chuan Da Cui ◽  
Jing Tao Han
Keyword(s):  
Cooling Rate ◽  
Hot Deformation ◽  
Transformation Products ◽  
Thermal Simulation ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Microstructure Transformation ◽  
Cct Curve ◽  
Rate Form ◽  
Transformation Curve

The CCT (Continuous Cooling Transformation) curve of hot deformation austenite in 55SiCr steel was measured on Gleeble-1500 thermal simulation machine, the microstructure and hardness of transformation products under different cooling velocities were observed. The microstructure transformation regularity with being cooled continuously were emphatically researched at the cooling rate form 0.1°C/s to 15 °C/s. The results can provide a instruction for producing 55SiCr steel.

Method for Estimating the Critical Cooling Rate for Glass Formation from Isothermal TTT Data

2007 ◽  
Vol 336-338 ◽  
pp. 1874-1877 ◽  
Author(s):  
Dong Mei Zhu ◽  
Wan Cheng Zhou ◽  
Chandra S. Ray ◽  
Delbert E. Day
Keyword(s):  
Cooling Rate ◽  
Glass Formation ◽  
Lithium Disilicate ◽  
Nucleating Agent ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Critical Cooling Rate ◽  
Continuous Cooling ◽  
Transformation Curve ◽  
Continuous Cooling Transformation Curve

A method is proposed for estimating the critical cooling rate for glass formation and continuous cooling transformation curve (CCT) from isothermal TTT data. The critical cooling rates and CCT curves for a group of lithium disilicate glasses containing different amount of Pt as nucleating agent estimated through this method are compared with the experimentally measured values and it shows this method can give a reasonable estimation.

Continuous Cooling Transformation Behavior of Vercooling Austenite of Low Carbon-Manganese Steel

2011 ◽  
Vol 418-420 ◽  
pp. 523-527
Author(s):  
Li Wei Duan ◽  
Yun Li Feng ◽  
Xue Jing Qi
Keyword(s):  
Cooling Rate ◽  
Manganese Steel ◽  
Accelerated Cooling ◽  
Low Carbon ◽  
Transformation Behavior ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Transformation Rules ◽  
Experimental Deformation ◽  
Gleeble 3500

Continuous cooling transformation rules of Low Carbon-Manganese Steel were investigated on Gleeble-3500 thermomechanical simulator. The study indicates that as cooling rate increases, Ar3 loweres and Ar1 behaves similarly but much slowly. The microstructure composes of dominant ferrite and some pearlite. As cooling rate enhances, the ferritic grain become finer, when cooling rate is up to 30°C/s, a little bainite appears. With the increasing of cooling rate the dimension of ferrite decreases. Under the experimental deformation conditions, ferritic grain refinement gets weak when the cooling rate is greater than or equal to 20°C/s. Therefore, with a certain strain, ferritic grain can refined to some degree by accelerated cooling.

Sign in / Sign up

Export Citation Format

Share Document