scholarly journals Spaceborne observations of the lidar ratio of marine aerosols

2015 ◽  
Vol 15 (6) ◽  
pp. 3241-3255 ◽  
Author(s):  
K. W. Dawson ◽  
N. Meskhidze ◽  
D. Josset ◽  
S. Gassó

Abstract. Retrievals of aerosol optical depth (AOD) from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) satellite sensor require the assumption of the extinction-to-backscatter ratio, also known as the lidar ratio. This paper evaluates a new method to calculate the lidar ratio of marine aerosols using two independent sources: the AOD from the Synergized Optical Depth of Aerosols (SODA) project and the integrated attenuated backscatter from CALIOP. With this method, the particulate lidar ratio can be derived for individual CALIOP retrievals in single aerosol layer, cloud-free columns over the ocean. Global analyses are carried out using CALIOP level 2, 5 km marine aerosol layer products and the collocated SODA nighttime data from December 2007 to November 2010. The global mean lidar ratio for marine aerosols was found to be 26 sr, roughly 30% higher than the current value prescribed by the CALIOP standard retrieval algorithm. Data analysis also showed considerable spatiotemporal variability in the calculated lidar ratio over the remote oceans. The calculated marine aerosol lidar ratio is found to vary with the mean ocean surface wind speed (U10). An increase in U10 reduces the mean lidar ratio for marine regions from 32 ± 17 sr (for 0 < U10 < 4 m s−1) to 22 ± 7 sr (for U10 > 15 m s−1). Such changes in the lidar ratio are expected to have a corresponding effect on the marine AOD from CALIOP. The outcomes of this study are relevant for future improvements of the SODA and CALIOP operational product and could lead to more accurate retrievals of marine AOD.

2011 ◽  
Vol 11 (22) ◽  
pp. 11401-11413 ◽  
Author(s):  
V. P. Kiliyanpilakkil ◽  
N. Meskhidze

Abstract. The relationship between "clean marine" aerosol optical properties and ocean surface wind speed is explored using remotely sensed data from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board the CALIPSO satellite and the Advanced Microwave Scanning Radiometer (AMSR-E) on board the AQUA satellite. Detailed data analyses are carried out over 15 regions selected to be representative of different areas of the global ocean for the time period from June 2006 to April 2011. Based on remotely sensed optical properties the CALIPSO algorithm is capable of discriminating "clean marine" aerosols from other types often present over the ocean (such as urban/industrial pollution, desert dust and biomass burning). The global mean optical depth of "clean marine" aerosol at 532 nm (AOD532) is found to be 0.052 ± 0.038 (mean plus or minus standard deviation). The mean layer integrated particulate depolarization ratio of marine aerosols is 0.02 ± 0.016. Integrated attenuated backscatter and color ratio of marine aerosols at 532 nm were found to be 0.003 ± 0.002 sr−1 and 0.530 ± 0.149, respectively. A logistic regression between AOD532 and 10-m surface wind speed (U10) revealed three distinct regimes. For U10 ≤ 4 m s−1 the mean CALIPSO-derived AOD532 is found to be 0.02 ± 0.003 with little dependency on the surface wind speed. For 4 < U10 ≤ 12 m s−1, representing the dominant fraction of all available data, marine aerosol optical depth is linearly correlated with the surface wind speed values, with a slope of 0.006 s m−1. In this intermediate wind speed region, the AOD532 vs. U10 regression slope derived here is comparable to previously reported values. At very high wind speed values (U10 > 18 m s−1), the AOD532-wind speed relationship showed a tendency toward leveling off, asymptotically approaching value of 0.15. The conclusions of this study regarding the aerosol extinction vs. wind speed relationship may have been influenced by the constant lidar ratio used for CALIPSO-derived AOD532. Nevertheless, active satellite sensor used in this study that allows separation of maritime wind induced component of AOD from the total AOD over the ocean could lead to improvements in optical properties of sea spray aerosols and their production mechanisms.


2014 ◽  
Vol 14 (1) ◽  
pp. 213-244
Author(s):  
K. W. Dawson ◽  
N. Meskhidze ◽  
D. Josset ◽  
S. Gassó

Abstract. Retrievals of aerosol optical depth (AOD) from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) satellite sensor require the assumption of an extinction-to-backscatter ratio, also known as the lidar ratio. This paper evaluates a new method to calculate the lidar ratio of sea spray aerosol using two independent sources: the AOD from the Synergized Optical Depth of Aerosols (SODA) algorithm and the integrated attenuated backscatter from CALIOP. With this method, the particulate lidar ratio can be derived for individual CALIOP retrievals in single aerosol layer columns over the ocean. Global analyses are carried out using CALIOP level 2, 5 km sea spray aerosol layer products and the collocated SODA nighttime data from December 2007 to December 2009. The global mean lidar ratio for sea spray aerosols was found to be 26 sr, roughly 30% higher than the current value prescribed by CALIOP standard retrieval algorithm. Data analysis also showed considerable spatiotemporal variability in the calculated lidar ratio over the remote oceans. The calculated aerosol lidar ratios are shown to be inversely related to the mean ocean surface wind speed: increase in ocean surface wind speed (U10) from 0 to >15 m s−1 reduces the mean lidar ratios for sea spray particles from 32 sr (for 015 m s−1). Such changes in the lidar ratio are expected to have a corresponding effect on the sea spray AOD. The outcomes of this study are relevant for future improvements of the SODA and CALIOP operational product and could lead to more accurate retrievals of sea spray AOD.


2014 ◽  
Vol 7 (6) ◽  
pp. 6141-6204 ◽  
Author(s):  
R. R. Rogers ◽  
M. A. Vaughan ◽  
C. A. Hostetler ◽  
S. P. Burton ◽  
R. A. Ferrare ◽  
...  

Abstract. The Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) instrument onboard the Cloud Aerosol Lidar and Pathfinder Satellite Observations (CALIPSO) spacecraft has provided over 8 years of nearly continuous vertical profiling of Earth's atmosphere. In this paper we investigate the CALIOP 532 nm aerosol layer optical depth (AOD) product, the AOD of individual layers, and the column AOD product, the sum AOD of the complete column, using an extensive database of coincident measurements. The CALIOP AOD measurements and AOD uncertainty estimates are compared with collocated AOD measurements collected with the NASA High Spectral Resolution Lidar (HSRL) in the North American and Caribbean regions. In addition, the CALIOP aerosol lidar ratios are investigated using the HSRL measurements. In general, compared with the HSRL values, the CALIOP layer AOD are biased high by less than 50% for AOD < 0.3 with higher errors for higher AOD. Less than 60% of the HSRL AOD measurements are encompassed within the CALIOP layer one-standard-deviation uncertainty range (around the CALIOP layer AOD), so an error estimate is created to encompass 68% of the HSRL data. Using this new metric, the CALIOP layer AOD error is estimated using the HSRL layer AOD as ± 0.035 ± 0.05 · (HSRL layer AOD) at night and ±0.05 ± 0.05 · (HSRL layer AOD) during the daytime. Furthermore, the CALIOP layer AOD error is found to correlate with aerosol loading as well as aerosol subtype, with the AODs in marine and dust layers agreeing most closely with the HSRL values. The lidar ratios used by CALIOP for polluted dust, polluted continental, and biomass burning layers are larger than the values measured by the HSRL in the CALIOP layers, and, therefore, the AODs for these types retrieved by CALIOP were generally too large. We estimated the CALIOP column AOD error can be expressed as ± 0.05 ± 0.07 · (HSRL column AOD) at night and ± 0.08 ± 0.1 · (HSRL column AOD) during the daytime. Multiple sources of error contribute to both positive and negative errors in the CALIOP column AOD, including multiple layers in the column of different aerosol types, lidar ratio errors, cloud misclassification, and undetected aerosol layers. The undetected layers were further investigated and we found that the layer detection algorithm works well at night, although undetected aerosols in the free troposphere introduce a mean underestimate of 0.02 in the column AOD in the dataset examined. The decreased SNR during the daytime led to poorer performance of the layer detection. This caused the daytime CALIOP column AOD to be less accurate than during the nighttime because CALIOP frequently does not detect optically thin aerosol layers with AOD < 0.1. Given that the median vertical extent of aerosol detected within any column was 1.6 km during the nighttime and 1.5 km during the daytime we can estimate the minimum extinction detection threshold to be 0.012 km−1 at night and 0.067 km−1 during the daytime in a layer median sense. This extensive validation of level 2 CALIOP aerosol layer optical depth products extends previous validation studies to nighttime lighting conditions and provides independent measurements of the lidar ratio, thus allowing the assessment of the effect on the CALIOP AOD of using inappropriate lidar ratio values in the extinction retrieval.


2011 ◽  
Vol 11 (2) ◽  
pp. 4599-4630 ◽  
Author(s):  
V. P. Kiliyanpilakkil ◽  
N. Meskhidze

Abstract. Relationship between "clean marine" aerosol optical properties and ocean surface wind speed is explored using remotely sensed data from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board the CALIPSO satellite and the Advanced Microwave Scanning Radiometer (AMSR-E) on board the AQUA satellite. Detailed data analyses are carried out over 15 regions selected to be representative of different areas of the global ocean for the time period from June 2006 to June 2010. Based on remotely sensed optical properties the CALIPSO algorithm is capable of discriminating "clean marine" aerosols from other types often present over the ocean (such as urban/industrial pollution, desert dust and biomass burning). The global mean optical depth of "clean marine" aerosol at 532 nm (AOD532) is found to be 0.052 ± 0.038. The mean layer integrated volume depolarization ratio of marine aerosols is 0.016 ± 0.012, the value representative of sea salt crystals. Integrated attenuated backscatter and color ratio of marine aerosols at 532 nm were obtained to be 0.003 ± 0.002 sr−1 and 0.530 ± 0.149, respectively. A logistic regression between AOD532 and 10-meter surface wind speed (U10) revealed three distinct regions. For surface winds lower than 4 m s−1, the mean CALIPSO-derived AOD532 is found to be 0.02 ± 0.003 with little dependency on the surface wind speed. For surface winds from 4 m s−1 to 12 m s−1, representing the dominant fraction of all available data, marine aerosol optical depth is linearly correlated with the U10, with a slope of 0.0062 s m−1. In this intermediate wind speed region, the AOD532 vs. U10 regression derived here is comparable to previously reported relationships. At very high wind speed values (U10 > 18 m s−1), the AOD532-wind speed relationship showed a tendency toward leveling off, suggesting the existence of some maximum value for maritime AOD. Results of our calculations suggest that considerable improvements to both optical properties of marine aerosols and their production mechanisms can be achieved by discriminating "clean marine" aerosols (or sea salt particles) from all other types of aerosols present over the ocean.


2021 ◽  
Author(s):  
Zhujun Li ◽  
David Painemal ◽  
Gregory Schuster ◽  
Marian Clayton ◽  
Richard Ferrare ◽  
...  

Abstract. We assess the CALIPSO Version 4.2 (V4) aerosol typing and assigned lidar ratios over ocean using aerosol optical depth (AOD) retrievals from the Synergized Optical Depth of Aerosols (SODA) algorithm and retrieved columnar lidar ratio estimated by combining SODA AOD and CALIPSO attenuated backscatter (CALIPSO-SODA). Six aerosol types – clean marine, dusty marine, dust, polluted continental/smoke, polluted dust, and elevated smoke – are characterized using CALIPSO-SODA over ocean and the results are compared against the prescribed V4 lidar ratios, when only one aerosol type is present in the atmospheric column. For samples detected at 5-km or 20-km spatial resolutions and having AOD > 0.05, the CALIPSO-SODA lidar ratios are significantly different between different aerosol types, and are consistent with the type-specific values assigned in V4 to within 10 sr (except for polluted continental/smoke). This implies that the CALIPSO classification scheme generally categorizes aerosols correctly. We find remarkable daytime/nighttime regional agreement for clean marine aerosol over the open ocean (CALIPSO-SODA = 20–25 sr, V4 = 23 sr), elevated smoke over the southeast Atlantic (CALIPSO-SODA = 65–75 sr, V4 = 70 sr), and dust over the subtropical Atlantic adjacent to the African continent (CALIPSO-SODA = 40–50 sr, V4 = 44 sr). In contrast, daytime polluted continental/smoke lidar ratio is more than 20 sr smaller than the constant V4 vaue for that type, attributed in part to the challenge of classifying tenuous aerosol with low signal-to-noise ratio. Dust over most of the Atlantic Ocean features CALIPSO-SODA lidar ratios less than 40 sr, possibly suggesting the presence of dust mixed with marine aerosols or lidar ratio values that depend on source and evolution of the aerosol plume. The new dusty marine type introduced in V4 features similar magnitudes and spatial distribution as its clean marine counterpart with lidar ratio differences of less than 3 sr, and nearly identical values over the open ocean, implying that some modification of the classification scheme for the marine subtypes is warranted.


2019 ◽  
Vol 12 (11) ◽  
pp. 6173-6191 ◽  
Author(s):  
Jayanta Kar ◽  
Kam-Pui Lee ◽  
Mark A. Vaughan ◽  
Jason L. Tackett ◽  
Charles R. Trepte ◽  
...  

Abstract. In August 2018, the Cloud–Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) project released a new level 3 stratospheric aerosol profile data product derived from nearly 12 years of measurements acquired by the spaceborne Cloud–Aerosol Lidar with Orthogonal Polarization (CALIOP). This monthly averaged, gridded level 3 product is based on version 4 of the CALIOP level 1B and level 2 data products, which feature significantly improved calibration that now makes it possible to reliably retrieve profiles of stratospheric aerosol extinction and backscatter coefficients at 532 nm. This paper describes the science algorithm and data handling techniques that were developed to generate the CALIPSO version 1.00 level 3 stratospheric aerosol profile product. Further, we show that the extinction profiles (retrieved using a constant lidar ratio of 50 sr) capture the major stratospheric perturbations in both hemispheres over the last decade resulting from volcanic eruptions, extreme smoke events, and signatures of stratospheric dynamics. Initial assessment of the product by intercomparison with the stratospheric aerosol retrievals from the Stratospheric Aerosol and Gas Experiment III (SAGE III) on the International Space Station (ISS) indicates good agreement in the tropical stratospheric aerosol layer (30∘ N–30∘ S), where the average difference between zonal mean extinction profiles is typically less than 25 % between 20 and 30 km (CALIPSO biased high). However, differences can exceed 100 % in the very low aerosol loading regimes found above 25 km at higher latitudes. Similarly, there are large differences (≥100 %) within 2 to 3 km above the tropopause that might be due to cloud contamination issues.


2010 ◽  
Vol 10 (14) ◽  
pp. 6711-6720 ◽  
Author(s):  
Y. Lehahn ◽  
I. Koren ◽  
E. Boss ◽  
Y. Ben-Ami ◽  
O. Altaratz

Abstract. Six years (2003–2008) of satellite measurements of aerosol parameters from the Moderate Resolution Imaging Spectroradiometer (MODIS) and surface wind speeds from Quick Scatterometer (QuikSCAT), the Advanced Microwave Scanning Radiometer (AMSR-E), and the Special Sensor Microwave Imager (SSM/I), are used to provide a comprehensive perspective on the link between surface wind speed and marine aerosol optical depth over tropical and subtropical oceanic regions. A systematic comparison between the satellite derived fields in these regions allows to: (i) separate the relative contribution of wind-induced marine aerosol to the aerosol optical depth; (ii) extract an empirical linear equation linking coarse marine aerosol optical depth and wind intensity; and (iii) identify a time scale for correlating marine aerosol optical depth and surface wind speed. The contribution of wind induced marine aerosol to aerosol optical depth is found to be dominated by the coarse mode elements. When wind intensity exceeds 4 m/s, coarse marine aerosol optical depth is linearly correlated with the surface wind speed, with a remarkably consistent slope of 0.009±0.002 s/m. A detailed time scale analysis shows that the linear correlation between the fields is well kept within a 12 h time frame, while sharply decreasing when the time lag between measurements is longer. The background aerosol optical depth, associated with aerosols that are not produced in-situ through wind driven processes, can be used for estimating the contributions of terrestrial and biogenic marine aerosol to over-ocean satellite retrievals of aerosol optical depth.


2009 ◽  
Vol 26 (4) ◽  
pp. 704-718 ◽  
Author(s):  
Bart De Paepe ◽  
Steven Dewitte

Abstract The authors present a new algorithm to retrieve aerosol optical depth (AOD) over a desert using the window channels centered at 8.7, 10.8, and 12.0 μm of the Spinning Enhanced Visible and Infrared Imager (SEVIRI) instrument on board the Meteosat Second Generation satellite. The presence of dust aerosols impacts the longwave outgoing radiation, allowing the aerosols over the desert surfaces to be detected in the thermal infrared (IR) wavelengths. To retrieve the aerosol properties over land, the surface contribution to the satellite radiance measured at the top of the atmosphere has to be taken into account. The surface radiation depends on the surface temperature, which is characterized by a strong diurnal variation over the desert, and the surface emissivity, which is assumed to be constant over a time span of 24 h. The surface emissivity is based on clear-sky observations that are corrected for atmospheric absorption and emission. The clear-sky image is a composite of pixels that is characterized by the highest brightness temperature (BT) of the SEVIRI channel at 10.8 μm, and by a negative BT difference between the channels at 8.7 and 10.8 μm. Because of the lower temperatures of clouds and aerosols compared to clear-sky conditions, the authors assume that the selected pixel values are obtained for a clear-sky day. A forward model is used to simulate the thermal IR radiation transfer in the dust layer. The apparent surface radiation for the three window channels in the presence of aerosols is calculated as a function of the surface emissivity and the surface temperature, the aerosol layer temperature, and the AOD for different aerosol loadings. From these simulations two emissivity ratios, which are stored in lookup tables (LUT), are calculated. The retrieval algorithm consists of processing the clear-sky image and computing the surface emissivity, processing the instantaneous image, and computing the apparent surface radiation for the three window channels. The two emissivity ratios are computed using the radiances at 8.7 and 10.8 μm and at 8.7 and 12.0 μm, respectively. The SEVIRI AOD is obtained by the inversion of these emissivity ratios using the corresponding LUT. The algorithm is applied to a minor dust event over the Sahara between 19 and 22 June 2007. For the validation the SEVIRI AOD is compared with the AOD from the Cloud Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) along the satellite track.


2016 ◽  
Author(s):  
Diego A. Gouveia ◽  
Boris Barja ◽  
Henrique M. J. Barbosa ◽  
Theotônio Pauliquevis ◽  
Paulo Artaxo

Abstract. For one year, from July 2011 to June 2012, a ground-based raman lidar provided atmospheric observations north of Manaus, Brazil, at an experimental site (2.89° S and 59.97° W) for long-term aerosol and cloud measurements. Upper tropospheric cirrus clouds were observed more frequently than previous reports in tropical regions. The frequency of occurrence was found to be as high as 82 % during the wet season and not lower than 55 % during the dry season. The diurnal cycle shows a minimum around local noon and maximum during late afternoon, associated with the diurnal cycle precipitation. Optical and geometrical characteristics of these cirrus clouds were derived. The mean values were 14.4 ± 2.0 km (top), 12.7 ± 2.3 km (base), 1.7 ± 1.5 km (thickness), and 0.36 ± 1.20 (cloud optical depth). Cirrus clouds were found at temperatures down to –90 °C and 7 % were above the tropopause base. The vertical distribution was not uniform and two cloud types were identified: (1) cloud base > 14 km and optical depth ~0.02, and (2) cloud base < 14 km and optical depth ~0.2. A third type, not previously reported, was identified during the wet season, between 16 and 18 km with optical depth ~0.005. The mean lidar ratio was 20.2 ± 7.0 sr, indicating a mixture of thick plates and long columns. However, the clouds above 14 km have a bimodal distribution during the dry season with a secondary peak at about 40 sr suggesting that thin plates are a major habit. A dependence of the lidar ratio with cloud temperature (altitude) was not found, thus indicating they are well mixed in the vertical. Cirrus clouds classified as subvisible (τ < 0.03) were 40 %, whilst 37.7 % were thin cirrus (0.03 < τ < 0.3) and 22.3 % opaque cirrus (τ > 0.3). Hence, not only does the central Amazon have a high frequency of cirrus clouds, but a large fraction of subvisible cirrus clouds as well. This high frequency of subvisible cirrus clouds may contaminate aerosol optical depth measured by sun-photometers and satellite sensors to an unknown extent.


2018 ◽  
Vol 11 (10) ◽  
pp. 5701-5727 ◽  
Author(s):  
Stuart A. Young ◽  
Mark A. Vaughan ◽  
Anne Garnier ◽  
Jason L. Tackett ◽  
James D. Lambeth ◽  
...  

Abstract. The Cloud–Aerosol Lidar with Orthogonal Polarization (CALIOP) on board the Cloud–Aerosol Lidar Infrared Pathfinder Satellite Observations (CALIPSO) satellite has been making near-global height-resolved measurements of cloud and aerosol layers since mid-June 2006. Version 4.10 (V4) of the CALIOP data products, released in November 2016, introduces extensive upgrades to the algorithms used to retrieve the spatial and optical properties of these layers, and thus there are both obvious and subtle differences between V4 and previous data releases. This paper describes the improvements made to the extinction retrieval algorithms and illustrates the impacts of these changes on the extinction and optical depth estimates reported in the CALIPSO lidar level 2 data products. The lidar ratios for both aerosols and ice clouds are generally higher than in previous data releases, resulting in generally higher extinction coefficients and optical depths in V4. A newly implemented algorithm for retrieving extinction coefficients in opaque layers is described and its impact examined. Precise lidar ratio estimates are also retrieved in these opaque layers. For semi-transparent cirrus clouds, comparisons between CALIOP V4 optical depths and the optical depths reported by MODIS collection 6 show substantial improvements relative to earlier comparisons between CALIOP version 3 and MODIS collection 5.


Sign in / Sign up

Export Citation Format

Share Document