Formulation and Evaluation of Benidipine Nanosuspension

2021 ◽  
pp. 4111-4116
Author(s):  
Sejal Patel ◽  
Anita P. Patel
Keyword(s):  
Particle Size ◽  
Water Solubility ◽  
Polymer Concentration ◽  
Oral Route ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Scanning Calorimetry ◽  
23 Factorial Design ◽  
Selection Of

In the interest of administration of dosage form oral route is most desirable and preferred method. After oral administration to get maximum therapeutic effect, major challenge is their water solubility. Water insoluble drug indicate insufficient bioavailability as well dissolution resulting in fluctuating plasma level. Benidipine (BND) is poorly water soluble antihypertensive drug has lower bioavailability. To improve bioavailability of Benidipine HCL, BND nanosuspension was formulated using media milling technique. HPMC E5 was used to stabilize nanosuspension. The effect of different important process parameters e.g. selection of polymer concentration X1(1.25 mg), stirring time X2 (800 rpm), selection of zirconium beads size X3 (0.4mm) were investigated by 23 factorial design to accomplish desired particle size and saturation solubility. The optimized batch had 408 nm particle size Y1, and showed in-vitro dissolution Y2 95±0.26 % in 30 mins and Zeta potential was -19.6. Differential scanning calorimetry (DSC) and FT-IR analysis was done to confirm there was no interaction between drug and polymer.

Formulation and Characterization of Nateglinide Nanosuspension by Precipitation Method

2014 ◽  
Vol 7 (4) ◽  
pp. 2685-2691
Author(s):  
Amruta Papdiwal ◽  
Kishor Sagar ◽  
Vishal Pande
Keyword(s):  
Particle Size ◽  
Dissolution Rate ◽  
Water Solubility ◽  
Average Particle Size ◽  
Biologically Active ◽  
In Vitro Dissolution ◽  
Precipitation Method ◽  
Average Particle ◽  
Scanning Calorimetry

Poor water solubility and slow dissolution rate are major issues for the majority of upcoming and existing biologically active pharmaceutical compounds. Nateglinide is Biopharmaceutical Classification System Class-II drug that has low solubility and high permeability. The purpose of the present study was to improve the solubility and dissolution rate of Nateglinide by the preparation of nanosuspension by the nanoprecipitation technique. Nateglinide nanosuspension was evaluated for its particle size, in vitro dissolution study, and characterized by differential scanning calorimetry and scanning electron microscopy. The optimized formulation showed an average particle size of 207 nm and zeta potential of -25.8 mV. The rate of dissolution of the optimized nanosuspension was enhanced by 83% in 50 min relative to micronized suspension of nateglinide (37% in 50 min). This improvement was mainly due to the formulation of nanosized particles of Nateglinide. Stability study revealed that nanosuspension was more stable at room temperature and refrigerator condition with no significant change in particle size distribution. These results indicate that the nateglinide loaded nanosuspension may significantly improve in vitro dissolution rate and thereby possibly enhance the onset of therapeutic effect.

scholarly journals Formulation and Optimization of Nanosuspension Prepared By Media Milling Technique to Enhance the Solubility of Isradipine

2017 ◽  
Vol 9 (04) ◽  
Author(s):  
Umang Motka ◽  
Mahesh Dabhi ◽  
Navin Sheth ◽  
Ashvin Dudhrejiya
Keyword(s):  
Particle Size ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Scanning Calorimetry ◽  
Particle Size Reduction ◽  
Saturation Solubility ◽  
Lattice Design ◽  
Media Milling ◽  
Stirring Time ◽  
Selection Of

Isradipine is a poorly water soluble antihypertensive drug has low bioavailability. The aim of this study was to formulate and characterize isradipine nanosuspension to enhance the solubility of isradipine and thus its bioavailability. Media milling technique was used for the formulation of nanosuspension. The effects of different important process parameters, i.e. the selection of stirring time, selection of concentration of zirconium beads, stirring speed were investigated by preliminary studies while concentration of stabilizers were optimized by simplex lattice design. Concentration of HPMC E3 LV(X1), Carbopol 934P(X2) and PVP K25(X3) were selected as the independent variables whereas mean particle size (Y1), saturation solubility (Y2) and cumulative percentage drug release (cpr) (Y3) were selected as dependent variables. The optimized batch had 100% w/v of zirconium beads, 0.5%w/v of PVP K25 as stabilizer, 0.1%w/v of isradipine, 15 ml of distilled water and 20 hours of stirring time. The particle size and zeta potential of optimized nanosuspension were 248.6 ± 20 nm and 13.96 ± 5 mV respectively. The size of particles of nanosuspension was measured by particle size analyser and transmission electron microscopy (TEM). Differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR) analysis indicated that there was no interaction between drug and stabilizers. The saturation solubility and in vitro dissolution rate of isradipine was significantly increased by particle size reduction and which may leads to increase the bio-availability of the Isaradipine. The stability study of the formulation was carried out for a period of 12 months.

Formulation and Evaluation of Nanosuspension of Simvastatin

2015 ◽  
Vol 8 (2) ◽  
pp. 2858-2873
Author(s):  
Rupali L. Shid ◽  
Shashikant N. Dhole ◽  
Nilesh Kulkarni ◽  
Santosh L Shid
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Factorial Design ◽  
Dissolution Rate ◽  
In Vitro Dissolution ◽  
Total Drug ◽  
23 Factorial Design ◽  
Rate Of Dissolution

Poor water solubility and slow dissolution rate are issues for the majority of upcoming and existing biologically active compounds. Simvastatin is poorly water-soluble drug and its bioavailability is very low from its crystalline form. The purpose of this study wasto increase the solubility and dissolution rate of simvastatin by the  preparation of nanosuspension by emulsification solvent diffusion method at laboratory scale. Prepared nanosus-pension was evaluated for its particle size and in vitro dissolution study and characterized by zeta potential,differential scanning calorimetry (DSC) and X-Ray diffractometry (XRD), motic digital microscopy, entrapment efficiency, total drug content, saturated solubility study and in vivo study. A 23 factorial design was employed to study the effect of independent variables, amount of SLS (X1), amount of PVPK-30 (X2) and poloxamer-188 (X3) and dependent variables are total drug content and polydispersity Index. The obtained results showed that particle size (nm) and rate of dissolution has been improved when nanosuspension prepared with the higherconcentration of PVPK-30 with the higher concentration of PVP K-30 and Poloxamer-188 and lower concentration of SLS. The particle size and zeta potential of optimized formulation was found to be 258.3 nm and 23.43. The rate of dissolution of the optimized nanosuspension was enhanced (90% in 60min), relative to plain simvastatin  (21% in 60 min), mainly due to the formation of nanosized particles. These results indicate the suitability of 23 factorial  design for preparation of simvastatin loaded nano-suspension significantly improved in vitro dissolution rate and thus possibly enhance fast onset of therapeutic drug effect. In vivo study shows increase in bioavailability in nanosuspension formulation than the plain simvastatin drug.

The Potential Migrated Mechanism of Water-Soluble Components in Pellets Prepared by Wet Extrusion/Spheronization: Effect of Drying Rate

2020 ◽  
Vol 17 ◽  
Author(s):  
Bingwei Wang ◽  
Jianping Liu ◽  
Zhenghua Li ◽  
Yulong Xia ◽  
Shuangshuang Zhang ◽  
...  
Keyword(s):  
Relative Humidity ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Drying Rate ◽  
Scanning Calorimetry ◽  
Drying Temperature ◽  
Wet Extrusion ◽  
Extrusion Spheronization ◽  
Soluble Components

Background: At present, there were numerous researches on the migration of components in tablets and granules, the investigation in the pharmaceutical literatrue concerning the effect of drying rate on the migration of water-soluble components of pellets was limited. Temperature and relative humidity (RH) were crucial parameters during the drying process which was an essential step in the preparation of pellets via wet extrusion/spheronization. To quantify these variables, the water loss percentage of pellets per minute was defined as drying rate. Objective: The study aimed to investigate the influence of drying rate on the migration of water-soluble components in wet pellets and the potential migrated mechanism. Methods: The pellets containing tartrazine as a water-soluble model drug and microcrystalline cellulose as a matrix former were prepared by extrusion/spheronization and dried at four different drying temperature and relative humidity. Afterward, the extent of migrated tartrazine was assessed regarding appearance, in-vitro dissolution test, Differential Scanning Calorimetry, X-Ray Powder Diffraction, Attenuated total reflectance Fourier transform infrared spectroscopy and Confocal Raman Mapping. Results: Results demonstrated that red spots of tartrazine appeared on the surface of pellets and more than 40% tartrazine were burst released within 5 minutes when pellets dried at 60℃/RH 10%. While pellets dried at 40℃/RH 80%, none of these aforementioned phenomena was observed. Conclusion: In conclusion, the faster drying rate was, the more tartrazine migrated to the exterior of pellets. Adjusting drying temperature and relative humidity appropriately could inhibit the migration of water-soluble components within wet extrusion/spheronization pellets.

scholarly journals FORMULATION AND CHARACTERIZATION OF GASTRORETENTIVE FLOATING MICROBALLOONS OF POORLY WATER-SOLUBLE DRUG DIACEREIN

2021 ◽  
Vol 15 (5) ◽  
pp. 8-12
Author(s):  
Kajal Tomer ◽  
Dilip Kumar Gupta
Keyword(s):  
Particle Size ◽  
Entrapment Efficiency ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Diffusion Method ◽  
Acrylic Polymer ◽  
Water Soluble Drug ◽  
Technological Advances ◽  
S 100

The drug can be released in a controlled manner using a gastro retentive dosage type. The main focus on the novel technological advances in the floating drug delivery method for gastric retention. The preparation of diacerein micro balloon is done by solvent diffusion method, using acrylic polymer like Eudragit S 100 and HPMC K4 M. The various evaluation of the prepared floating microsphere like its % yield, drug entrapment efficiency, particle size in-vitro dissolution, buoyancy, was studied. The floating microsphere was found to be spherical and range from 85 μm - 192 μm. Whereas the buoyancy in gastric mucosa between the range 30.5% -49.5%. The % yield and % entrapment efficiency were found under the range 61% - 82% and 45.1–84.1% respectively. The microsphere showed favorable in-vitro dissolution 76.8 to 94.45. The optimized formulation was found based on evaluation of floating micro-balloons, Formulation (M3E3) showed the best result as particle size 192 μm, DDE 84.1%, in vitro drug release 94.5%, and in vitro buoyancy 49.5%. all the formulations showed controlled release up to 24 hours.

scholarly journals Enhancement of Solubility and Improvement of Dissolution Rate of Atorvastatin Calcium Prepared as Nanosuspension

2019 ◽  
Vol 28 (2) ◽  
pp. 46-57
Author(s):  
Ahmed H. Ali ◽  
Shaimaa N. Abd-Alhammid
Keyword(s):  
Particle Size ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Precipitation Method ◽  
Size Analysis ◽  
Dissolution Profile ◽  
Disintegration Time ◽  
Atorvastatin Calcium ◽  
Freeze Dried

       Atorvastatin have problem of very slightly aqueous solubility (0.1-1 mg/ml). Nano-suspension is used to enhance it’s of solubility and dissolution profile. The aim of this study is to formulate Atorvastatin as a nano-suspension to enhance its solubility due to increased surface area of exposed for dissolution medium, according to Noyes-Whitney equation.         Thirty one formulae were prepared to evaluate the effect of ; Type of polymer, polymer: drug ratio, speed of homogenization, temperature of preparation and inclusion of co-stabilizer in addition to the primary one; using solvent-anti-solvent precipitation method under high power of ultra-sonication. In this study five types of stabilizers (TPGS, PVP K30, HPMC E5, HPMC E15, and Tween80) were used in three different concentrations 1:1, 1:0.75 and 1:0.5 for preparing of formulations. At the same time, tween80 and sodium lauryl sulphate have been added as a co-stabilizer.          Atorvastatin nano-suspensions were evaluated for particle size, PDI, zeta potential, crystal form and surface morphology. Finally, results of particle size analysis revealed reduced nano-particulate size to 81nm for optimized formula F18 with the enhancement of in-vitro dissolution profile up to 90% compared to 44% percentage cumulative release for the reference Atorvastatin calcium powder in 6.8 phosphate buffer media. Furthermore, saturation solubility of freeze dried Nano suspension showed 3.3, 3.8, and 3.7 folds increments in distilled water, 0.1N Hcl and 6.8 phosphate buffers, respectively. Later, freeze dried powder formulated as hard gelatin capsules and evaluated according to the USP specifications of the drug content and the disintegration time.        As a conclusion; formulation of poorly water soluble Atorvastatin calcium as nano suspension significantly improved the dissolution of the drug and enhances its solubility.

DEVELOPMENT AND EVALUATION OF ZIPRASIDONE LOADED SOLID SELF-MICRO EMULSIFYING DRUG DELIVERY SYSTEM

INDIAN DRUGS ◽  
2020 ◽  
Vol 57 (08) ◽  
pp. 53-60
Author(s):  
Purushottam Patil ◽  
Malik Shaikh ◽  
Paresh Mahaparale
Keyword(s):  
Drug Delivery ◽  
Drug Delivery System ◽  
Delivery System ◽  
Physical Adsorption ◽  
Gastrointestinal Transit ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Scanning Calorimetry ◽  
Poorly Water Soluble

Solid self-micro emulsification technique is the new approach for poorly water-soluble and poorly bioavailable drugs by allowing the drug substance to be incorporated into the oil phase and thus having the ability to permeate the GI membrane to a faster extent. Oleic acid, Tween 80, methanol and colloidal silicon dioxide were used as penetrant, surfactant, co-surfactant and adsorbent, respectively. The interaction between drug and excipients was examined by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The results of DSC and FTIR studies did not reveal any possible drug-excipient interactions. The conversion of liquid self-microemulsifying drug delivery system (SMEDDS) into the solid SMEDDS increases the stability of the emulsion formulation achieved by physical adsorption of an adsorbent material. The release of drug from SMEDDS formulation is justified by in-vitro dissolution studies. SMEDDS increases the solubility of the drug and improves the bioavailability, without disturbing gastrointestinal transit. SMEDDS has the potential to provide a useful oral solid dosage form for the poorly water-soluble drug ziprasidone.

Development and Characterization of the Neuroregenerative Xanthohumol C/Hydroxypropyl-β-cyclodextrin Complex Suitable for Parenteral Administration

Planta Medica ◽  
2019 ◽  
Vol 85 (16) ◽  
pp. 1233-1241
Author(s):  
Michael Kirchinger ◽  
Lara Bieler ◽  
Julia Tevini ◽  
Michael Vogl ◽  
Elisabeth Haschke-Becher ◽  
...  
Keyword(s):  
Water Solubility ◽  
Pharmaceutical Research ◽  
Water Soluble ◽  
Complexing Agents ◽  
Cyclodextrin Complex ◽  
Scanning Calorimetry ◽  
In Vivo Experiments ◽  
Strong Candidate

AbstractThe chroman-like chalcone Xanthohumol C, originally found in hops, was demonstrated to be a potent neuroregenerative and neuroprotective natural product and therefore constitutes a strong candidate for further pharmaceutical research. The bottleneck for in vivo experiments is the low water solubility of this chalcone. Consequently, we developed and validated a suitable formulation enabling in vivo administration. Cyclodextrins were used as water-soluble and nontoxic complexing agents, and the complex of Xanthohumol C and 2-hydroxypropyl-β-cyclodextrin was characterized using HPLC, HPLC-MS, NMR, and differential scanning calorimetry. The water solubility of Xanthohumol C increases with increasing concentrations of cyclodextrin. Using 50 mM 2-hydroxypropyl-β-cyclodextrin, solubility was increased 650-fold. Furthermore, in vitro bioactivity of Xanthohumol C in free and complexed form did not significantly differ, suggesting the release of Xanthohumol C from 2-hydroxypropyl-β-cyclodextrin. Finally, a small-scaled in vivo experiment in a rat model showed that after i. p. administration of the complex, Xanthohumol C can be detected in serum, the brain, and the cerebrospinal fluid at 1 and 6 h post-administration. Mean (± SD) Xanthohumol C serum concentrations after 1, 6, and 12 h were determined as 463.5 (± 120.9), 61.9 (± 13.4), and 9.3 (± 0.8) ng/mL upon i. v., and 294.3 (± 22.4), 45.5 (± 0.7), and 13 (± 1.0) ng/mL after i. p. application, respectively. Accordingly, the formulation of Xanthohumol C/2-hydroxypropyl-β-cyclodextrin is suitable for further in vivo experiments and further pharmaceutical research aiming for the determination of its neuroregenerative potential in animal disease models.

scholarly journals Formulation and Evaluation of Acyclovir Microspheres

2018 ◽  
Vol 27 (1) ◽  
pp. 1-7
Author(s):  
Pavani S ◽  
Mounika K ◽  
Naresh K
Keyword(s):  
Particle Size ◽  
Sustained Release ◽  
Sodium Alginate ◽  
Calcium Chloride ◽  
Polymer Concentration ◽  
Entrapment Efficiency ◽  
In Vitro Dissolution ◽  
Release Mechanism ◽  
Natural Polymers

The present study is to formulate and evaluate Acyclovir (ACV) microspheres using natural polymers like chitosan and sodium alginate. ACV is a DNA polymerase inhibitor used in treating herpes simplex virus infection and zoster varicella infections. Acyclovir is a suitable candidate for sustained-release (SR) administration as a result of its dosage regimen twice or thrice a day and relatively short plasma half-life (approximately 2 to 4 hours). Microspheres of ACV were prepared by an ionic dilution method using chitosan and sodium alginate as polymers. The prepared ACV microspheres were then subjected to FTIR, SEM, particle size, % yield, entrapment efficiency, in vitro dissolution studies and release kinetics mechanism. The FTIR spectra’s revealed that, there was no interaction between polymer and ACV. ACV microspheres were spherical in nature, which was confirmed by SEM. The particle size of microspheres was in the range of 23.8µm to 39.4µm. 72.9% drug entrapment efficiency was obtained in the formulation F3 (1:3 ratio) with a high concentration of calcium chloride (4% w/v). The in vitro performance of ACV microspheres showed sustained release depending on the polymer concentration and concentration of calcium chloride.   The release data was best fitted with zero order kinetics and Korsemeyer -Peppas release mechanism and diffusion exponent ‘n’ value of was found to be Non-Fickian.

scholarly journals Development and Biopharmaceutical Evaluation of Tablets Based on the Poorly Water-soluble Substance 1-[2-(2-benzoylphenoxy)ethyl]-6-methyluracil

2020 ◽  
Vol 9 (4) ◽  
pp. 79-87
Author(s):  
D. V. Demchenko ◽  
E. A. Jain (Korsakova) ◽  
V. Yu. Balabanyan ◽  
M. N. Makarova ◽  
V. G. Makarov
Keyword(s):  
Solid Dispersion ◽  
Solid Dispersions ◽  
Active Pharmaceutical Ingredient ◽  
Oral Route ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Technological Properties ◽  
Enhanced Dissolution ◽  
Dispersion Technique

Introduction. 1-[2-(2-benzoylphenoxy)ethyl]-6-methyluracil is a substance of scientific interest intended for the treatment of HIV-infection. However, its low bioavailability is a major limitation in successful drug delivery by oral route. Therefore, the objective of the present work was to enhance itssolubility by using solid dispersion technique followed by the development of a solid dosage form.Aim. Development of the composition and technology of tablets based on 1- [2-(2-benzoylphenoxy)ethyl]-6-methyluracil with the appropriate technological properties providing the most complete release of the active pharmaceutical ingredient (API) in vitro.Materials and methods. The pharmaceutical substance 1-[2-(2-benzoylphenoxy) ethyl]-6-methyluracil is a crystalline powder with poor solubility. Solid dispersions were prepared using Lactose, Kollidon® 17PF, Kollidon® 30, Kollidon® VA64, Kollidon 90F, and PEG-6000 as a carrier mostly in 1:4 ratio by two methods – co-melting and solvent evaporation. The technological properties of substance, tablet masses and tablet quality were determined according to the methods described in the State Pharmacopoeia of the Russian Federation (14th edition).Results and discussion. Article shows the results of development of the composition and technology of a medicine in the form of tablets based on the substance 1-[2-(2-benzoylphenoxy)ethyl]-6-methyluracil. Solid dispersion technique was used to improve the biopharmaceutical properties of 1-[2-(2-benzoylphenoxy)ethyl]-6-methyluracil.Conclusion. In vitro dissolution studies showed enhanced dissolution rate of the drug-loaded solid dispersion with Kollidon 17PF as a carrier as compared to pure drug.

Sign in / Sign up

Export Citation Format

Share Document