scholarly journals CONSTRUCTAL DESIGN OF FINS IN COOLED CAVITIES BY NON-NEWTONIAN FLUIDS

2019 ◽  
Vol 18 (1) ◽  
pp. 85
Author(s):  
J. F. Bueno ◽  
A. R. S. Silva ◽  
T. A. Hirt ◽  
G. F. C. Bogo ◽  
F. S. F. Zinani ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Newtonian Fluids ◽  
Rheological Parameters ◽  
Flow Index ◽  
Pseudoplastic Fluid ◽  
High Reynolds ◽  
Energy Equations ◽  
Rayleigh Numbers

The present work investigates the Construtal Design of fins inserted in cavities submitted to mixed convection by non-Newtonian fluids. The objective is to obtain the optimum aspect ratio for the fin considering different flow conditions and variations in the rheological parameters of the fluid. The phenomena of flow and heat transfer are modeled by mass balance, momentum and energy equations, and by the generalized Newtonian liquid constitutive equation. The viscosity is modeled as that of a pseudoplastic fluid, using the Carreau function. The optimization problem consists in maximizing heat transfer from the fin using the average Nusselt number. The investigated project variable is the aspect ratio between the edges of the rectangular plane fin profile. The restrictions are the volume of the cavity and the fin. The results are obtained numerically using a finite volume code and a two-dimensional geometry, through exhaustive searching. The results show that the fin geometry influences the maximum Nusselt number mainly for the cases with high Reynolds and Rayleigh numbers, such as was shown in previous studies. The results show that the fin geometry influences the maximum Nusselt number mainly for the cases with high Reynolds and Rayleigh numbers, as was shown in previous studies. It was also found that the Nusselt number increases as the increase in flow intensity, represented by the parameter p, and that the result of the maximum Nusselt number does not change monotonically with the non-Newtonian dimensionless viscosity and with the flow index, showing that the pseudoplasticity of the fluid implies optimal configurations very different from those predicted for Newtonian fluids.

Effects of slip and rheological parameters on the flow and heat transfer of a Herschel-Bulkley fluid

2017 ◽  
Vol 27 (4) ◽  
pp. 981-999 ◽  
Author(s):  
Zefeng Jing ◽  
Shuzhong Wang ◽  
Zhende Zhai
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Slip Flow ◽  
Critical Value ◽  
Small Radius ◽  
Rheological Parameters ◽  
Parameter Method ◽  
Pseudoplastic Fluid ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to investigate the combined effects of slip and rheological parameters on the flow and heat transfer of the Herschel-Bulkley fluid. Design/methodology/approach The combinative dimensionless parameter method is introduced into the equations of the slip flow and heat transfer to make the discussion more comprehensive. More specifically, the slip and rheological parameters are transformed into the dimensionless slip number as well as Herschel-Bulkley number. We solve the dimensionless equations and then focus on the effects of these parameters on the slip flow and heat transfer. Findings The results show that, for a given value of Herschel-Bulkley number, there is a finite critical value of slip number at which the pressure gradient reaches the lowest value and both the dimensionless yield radius and slip velocity become 1. Meanwhile, the Nusselt number tends to be infinite at this critical value of slip number. For the case of slip, the Nusselt number also approaches infinity at a finite critical value of Herschel-Bulkley number. Furthermore, the dimensionless velocity as well as temperature of the yield pseudoplastic fluid with higher slip number is lower within a small radius but becomes higher near the wall. Meanwhile, from the velocity and temperature profiles, the effect of Herschel-Bulkley number on these two parameters of the Bingham fluid at the smaller radius is opposite. Originality/value These associated expressions can be generalized to the flow and heat transfer of a Herschel-Bulkley fluid under slip boundary condition. It can provide a reference for the engineering application relating to the heat transfer and flow of a Herschel-Bulkley fluid. Meanwhile, it also suggests some revelations for dealing with this similar problem.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

An Experimental Study of Free Corrective Heat Transfer in a Parallelogrammic Enclosure

1983 ◽  
Vol 105 (3) ◽  
pp. 433-439 ◽  
Author(s):  
N. Seki ◽  
S. Fukusako ◽  
A. Yamaguchi
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Nusselt Number ◽  
Correlation Equation ◽  
Transformer Oil ◽  
Experimental Measurements ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Prandtl Numbers ◽  
Rayleigh Numbers

Experimental measurements are presented for free convective heat transfer across a parallelogrammic enclosure with the various tilt angles of parallel upper and lower walls insulated. The experiments covered a range of Rayleigh numbers between 3.4 × 104 and 8.6 × 107, and Prandtl numbers between 0.70 and 480. Those also covered the tilt angles of the parallel insulated walls with respect to the horizontal, φ, of 0, ±25, ±45, ±60, and ±70 deg under an aspect ratio of H/W = 1.44. The fluids used were air, transformer oil, and water. It was found that the heat transfer coefficients for φ = −70 deg were decreased to be about 1/18 times those for φ = 0 deg. Experimental results are given as plots of the Nusselt number versus the Rayleigh number. A correlation equation is given for the Nusselt number, Nu, as a function of φ, Pr, and Ra.

Heat Transfer Characteristics of the Phase Change Material Microcapsule Slurry in Solid Phase State

2011 ◽  
Vol 71-78 ◽  
pp. 1187-1190
Author(s):  
Yan Lai Zhang ◽  
Zhong Hao Rao ◽  
Shuang Feng Wang ◽  
Hong Zhang ◽  
Li Jun Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Phase State ◽  
Solid Phase ◽  
Heat Transfer Characteristics ◽  
Rectangular Enclosure ◽  
Transfer Characteristics ◽  
Change Material

This experiment is performed to investigate heat transfer characteristics with the PCM microcapsule slurry in a solid phase state at a horizontal rectangular enclosure heating from below and cooling from top. Some important parameters are taken into account such as the mass concentration of the PCM, the temperature difference between heating plate and cooling plate, Nusselt number Nu, Rayleigh number Ra and the aspect ratio (width/height) of the horizontal rectangular enclosure. Experiment is done under the thermal steady condition in the PCM microcapsule slurry. Heat transfer coefficient is measured under various temperature differences in PCM mass concentrations of 10% and 20%. And relationship with Nusselt number Nu and Rayleigh number Ra is summarized to various heights H or the aspect ratio (width/height) Ar of enclosure.

Numerical Simulation of Flow and Heat Transfer in Rectangular Channel With Different Aspect Ratios

2016 ◽  
Author(s):  
Liu Wenhua ◽  
Mo Yang ◽  
Li Ling ◽  
Qiao Liang ◽  
Yuwen Zhang
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Characteristic Length ◽  
Rectangular Channel ◽  
Equivalent Diameter ◽  
Correction Coefficient ◽  
Corner Region ◽  
Flow And Heat Transfer ◽  
Aspect Ratios

Turbulent flow and heat transfer in rectangular channel has an important significance in engineering. Conventional approach to caculate Nusselt number of rectangular channel approximately is to take the equivalent diameter as the characteristic length and use the classic circular channel turbulent heat transfer coefficient correlations. However, under these conditions, the caculation error of Nusselt number can reach to 14% and thus this approach can not substantially describe the variation of Nusselt number of rectangular cross-sections with different aspect ratios. Therefore, caculation by using equivalent diameter as the characteristic length in classic experiment formula needs to be corrected. Seven groups of rectangular channel models with different aspect ratios have been studied numerically in this paper. By using standard turbulence model, the flow and heat transfer law of air with varing properties has been studied in 4 different sets of conditions in Reynolds number. The simulation and experimental results are in good agreement. The simulation results show that with the increase of aspect ratio, the cross-sectional average Nusselt number increased, Nusselt number of circumferential wall distributed more evenly and the difference between the infinite plate channel and square channel went up to 25%. The effects of corner region and long\short sides on heat transfer have also been investigated in this paper. Results show that in rectangular channel, heat transfer in corner region is significantly weaker than it in other region. With the increase of aspect ratio, effect on the long side of heat transfer of the short side is gradually reduced, and then eventually eliminates completely in the infinite flat place. Based on the studies above, correction coefficient for rectangular channels with different aspect ratios has been proposed in this paper and the accuracy of the correction coefficient has been varified by numerical simulations. This can reflect the variation of Nusselt number under different aspect ratios more effectively and thus has current significance for project to calculate Nusselt number of heat transfer in rectangular channel.

scholarly journals Effects of a Rotating Cone on the Mixed Convection in a Double Lid-Driven 3D Porous Trapezoidal Nanofluid Filled Cavity under the Impact of Magnetic Field

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 449 ◽  
Author(s):  
Ali J. Chamkha ◽  
Fatih Selimefendigil ◽  
Hakan F. Oztop
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Mixed Convection ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Rotational Velocity ◽  
Rotating Cone ◽  
The Impact

Effects of a rotating cone in 3D mixed convection of CNT-water nanofluid in a double lid-driven porous trapezoidal cavity is numerically studied considering magnetic field effects. The numerical simulations are performed by using the finite element method. Impacts of Richardson number (between 0.05 and 50), angular rotational velocity of the cone (between −300 and 300), Hartmann number (between 0 and 50), Darcy number (between 10 − 4 and 5 × 10 − 2 ), aspect ratio of the cone (between 0.25 and 2.5), horizontal location of the cone (between 0.35 H and 0.65 H) and solid particle volume fraction (between 0 and 0.004) on the convective heat transfer performance was studied. It was observed that the average Nusselt number rises with higher Richardson numbers for stationary cone while the effect is reverse for when the cone is rotating in clockwise direction at the highest supped. Higher discrepancies between the average Nusselt number is obtained for 2D cylinder and 3D cylinder configuration which is 28.5% at the highest rotational speed. Even though there are very slight variations between the average Nu values for 3D cylinder and 3D cone case, there are significant variations in the local variation of the average Nusselt number. Higher enhancements in the average Nusselt number are achieved with CNT particles even though the magnetic field reduced the convection and the value is 84.3% at the highest strength of magnetic field. Increasing the permeability resulted in higher local and average heat transfer rates for the 3D porous cavity. In this study, the aspect ratio of the cone was found to be an excellent tool for heat transfer enhancement while 95% enhancements in the average Nusselt number were obtained. The horizontal location of the cone was found to have slight effects on the Nusselt number variations.

Effects of Variable Viscosity and Thermal Conductivity of CuO-Water Nanofluid on Heat Transfer Enhancement in Natural Convection: Mathematical Model and Simulation

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
Eiyad Abu-Nada
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Variable Viscosity ◽  
Cylinder Surface ◽  
Transfer Enhancement

Heat transfer enhancement in horizontal annuli using variable thermal conductivity and variable viscosity of CuO-water nanofluid is investigated numerically. The base case of simulation used thermal conductivity and viscosity data that consider temperature property dependence and nanoparticle size. It was observed that for Ra≥104, the average Nusselt number was deteriorated by increasing the volume fraction of nanoparticles. However, for Ra=103, the average Nusselt number enhancement depends on aspect ratio of the annulus as well as volume fraction of nanoparticles. Also, for Ra=103, the average Nusselt number was less sensitive to volume fraction of nanoparticles at high aspect ratio and the average Nusselt number increased by increasing the volume fraction of nanoaprticles for aspect ratios ≤0.4. For Ra≥104, the Nusselt number was deteriorated everywhere around the cylinder surface especially at high aspect ratio. However, this reduction is only restricted to certain regions around the cylinder surface for Ra=103. For Ra≥104, the Maxwell–Garnett and the Chon et al. conductivity models demonstrated similar results. But, there was a deviation in the prediction at Ra=103 and this deviation becomes more significant at high volume fraction of nanoparticles. The Nguyen et al. data and the Brinkman model give completely different predictions for Ra≥104, where the difference in prediction of the Nusselt number reached 50%. However, this difference was less than 10% at Ra=103.

Effect of Wall Conduction on Combined Free and Forced Laminar Convection in Horizontal Rectangular Channels

1987 ◽  
Vol 109 (4) ◽  
pp. 936-942 ◽  
Author(s):  
G. J. Hwang ◽  
F. C. Chou
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Temperature Distribution ◽  
Finite Difference ◽  
Aspect Ratio ◽  
Finite Difference Method ◽  
Numerical Study ◽  
Fully Developed Flow ◽  
Rectangular Channels ◽  
Laminar Convection

This paper presents a numerical study of the effect of peripheral wall conduction on combined free and forced laminar convection in hydrodynamically and thermally fully developed flow in horizontal rectangular channels with uniform heat input axially, In addition to the Prandtl number, the Grashof number Gr+, and the aspect ratio γ, a parameter Kp indicating the significance of wall conduction plays an important role in heat transfer. A finite-difference method utilizing a power-law scheme is employed to solve the system of governing partial differential equations coupled with the equation for wall conduction. The numerical solution covers the parameters: Pr = 7.2 and 0.73, γ = 0.5, 1, and 2, Kp = 10−4–104, and Gr+ = 0–1.37×105. The flow patterns and isotherms, the wall temperature distribution, the friction factor, and the Nusselt number are presented. The results show a significant effect of the conduction parameter Kp.

Numerical Simulation of Natural Convection Flow in a Cube With a Horizontal Heated Strip

2008 ◽  
Author(s):  
Esam M. Alawadhi
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Nusselt Number ◽  
High Temperature ◽  
Natural Convection ◽  
Vertical Wall ◽  
Convection Flow ◽  
Front Wall ◽  
Natural Convection Flow ◽  
Rayleigh Numbers

Natural convection flow in a cube with a heated strip is solved numerically. The heated strip is attached horizontally to the front wall and maintained at high temperature, while the entire opposite wall is maintained at low temperature. The heated strip simulates an array of electronic chips The Rayleigh numbers of 104, 105, and 106 are considered in the analysis and the heated strip is horizontally attached to the wall. The results indicate that the heat transfer strongly depends on the position of the heated strip. The maximum Nusselt number can be achieved if the heater is placed at the lower half of the vertical wall. Increasing the Rayleigh number significantly promotes heat transfer in the enclosure. Flow streamlines and temperature contours are presented, and the results are validated against published works.

The Aspect Ratio Effect on Natural Convection in an Enclosure With Protruding Heat Sources

1991 ◽  
Vol 113 (4) ◽  
pp. 883-891 ◽  
Author(s):  
M. Keyhani ◽  
L. Chen ◽  
D. R. Pitts
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Aspect Ratio ◽  
Vertical Wall ◽  
Heat Sources ◽  
Ratio Effect ◽  
Vertical Spacing ◽  
Vertical Height ◽  
Cavity Width

The aspect ratio effect on natural convection heat transfer in a rectangular enclosure with protruding heat sources has been experimentally investigated. Five protruding heaters were mounted with uniform vertical spacing on one vertical wall. The vertical wall opposite to the wall on which heated sections were mounted was movable so that the enclosure width could be adjusted to the desired value. The top surface of the test enclosure was an isothermal heat sink. All other surfaces except the two end vertical surfaces were insulated. The five heaters were identical with each having horizontal protuberance of L3 = 9 mm and vertical height of L1 = 15 mm. The vertical spacing between the heaters was L2 = 15 mm. The enclosure width was varied in experiments from W = 13.5 mm to 45 mm. The experiments were conducted for six values of cavity width resulting in variations in the cavity height-to-width ratios (aspect ratios) and cavity width-to-protruding heater height ratios of 3.67 to 12.22 and 1.5 to 5.0, respectively. Ethylene glycol was used as the convective medium. Flow visualization pictures and heat transfer data indicate that the starting point of core flow directly affects the local heat transfer coefficient of the bottom heater, while the secondary flow cell between the top heated section and the top sink surface influences the heat transfer coefficient of the top heater. Cavity width variation influences the heat transfer process mainly through altered flow patterns. This influence is weak when the ratio of width-to-protruding height is 4.0 and negligible when this ratio is 5.0 or more. Based on the local height length scale (measured from the bottom of the cavity) the data for all the cavity widths are correlated and an explicit relation for the aspect ratio effect on local Nusselt number is reported. The correlation of local Nusselt number versus local modified Rayleigh number is independent of the number of heaters in the vertical array, cavity width-to-heater protrusion height ratio, W/L3, and vertical height location of the heaters. This conclusion is based on the present results and previously reported data and is valid for the following conditions: 1.5 ≤ W/L3 ≤ 5.0; 3.67 ≤ aspect ratio ≤ 1.22; vertical height of heater from 8 to 15 mm; and number of heated sections from 5 to 10.

Sign in / Sign up

Export Citation Format

Share Document