scholarly journals Comparison of slot deformation in stainless steel and ceramic brackets during torque: A finite element analysis

2017 ◽  
Vol 4 (1) ◽  
pp. 5-8 ◽  
Author(s):  
Pandurangan Harikrishnan ◽  
Varadaraju Magesh ◽  
Devadhas Kingsly-Jeba-Singh
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Element Analysis ◽  
Ceramic Brackets

Verification of a Finite Element Analysis Procedure for Modeling the Nonlinear, Monotonic In-Plane Behavior of 4 Inch, Schedule 10, Stainless Steel, 90° Elbows

2003 ◽  
Author(s):  
James K. Wilkins
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Nonlinear Behavior ◽  
Shell Element ◽  
Analysis Procedure ◽  
Hoop Strain ◽  
Element Analysis ◽  
Butt Welding ◽  
Strain Data

A project has been conducted to verify a finite element analysis procedure for studying the nonlinear behavior of 90°, stainless steel, 4 inch schedule 10, butt welding elbows. Two displacement controlled monotonic in-plane tests were conducted, one closing and one opening, and the loads, displacements, and strains at several locations were recorded. Stacked 90° tee rosette gages were used in both tests because of their ability to measure strain over a small area. ANSYS shell element 181 was used in the FEA reconciliations. The FEA models incorporated detailed geometric measurements of the specimens, including the welds, and material stress-strain data obtained from the attached straight piping. Initially, a mesh consisting of sixteen elements arrayed in 8 rings was used to analyze the elbow. The load-displacement correlation was quite good using this mesh, but the strain reconciliation was not. Analysis of the FEA results indicated that the axial and hoop strain gradients across the mid-section of the elbow were very high. In order to generate better strain correlations, the elbow mesh was refined in the mid-section of the elbow to include 48 elements per ring and an additional six rings, effectively increasing the element density by nine times. Using the refined mesh produced much better correlations with the strain data.

scholarly journals Finite Element Analysis of Camshaft Using Inventor Software

2021 ◽  
Vol 9 (12) ◽  
pp. 906-912
Author(s):  
Valentin Mereuta
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Cast Iron ◽  
3D Model ◽  
Steel Alloy ◽  
Element Analysis ◽  
Steel Aisi ◽  
The Comparative Study ◽  
Stainless Steel Aisi

Abstract: In this work the 3D model of the camshaft was done using Autodesk Inventor version 2021 with the literature data and finite element analysis is performed by applying restrictions and loads conditions, first by the absence of the torque and then by applying the torque. Three materials were analyzed in both situations: Cast Iron, Stainless Steel AISI 202 and Steel Alloy. Following the comparative study for the three materials, it can be specified the importance of the material for the construction of the camshaft. Keywords: Camshaft, Static analysis, Autodesk Inventor

Evaluation of Stiffness and Stress of External Fixators with Curved Acrylic Connecting Bars

2000 ◽  
Vol 13 (02) ◽  
pp. 65-72 ◽  
Author(s):  
R. Shahar
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Axial Compression ◽  
External Fixator ◽  
External Fixators ◽  
Analysis Method ◽  
Lateral Bending ◽  
Element Analysis ◽  
The Finite Element Analysis

SummaryThe use of acrylic connecting bars in external fixators has become widespread in veterinary orthopaedics. One of the main advantages of an acrylic connecting bar is the ability to contour it into a curved shape. This allows the surgeon to place the transcortical pins according to safety and convenience considerations, without being bound by the requirement of the standard stainless steel connecting bar, that all transcortical pins be in the same plane.The purpose of this study was to evaluate the stiffness of unilateral and bilateral medium-sized external fixator frames with different curvatures of acrylic connecting bars. Finite element analysis was used to model the various frames and obtain their stiffness under four types of load: Axial compression, four-point medio-lateral bending, fourpoint antero-posterior bending and torsion. The analysis also provided the maximal pin stresses occurring in each frame for each loading condition.Based on the results of this study, curvatures of acrylic connecting bars of up to a maximal angular difference between pins of 25° will result in very similar stiffness and maximal pin stresses to those of the equivalent, uniplanar stainless steel system. In both unilateral and bilateral systems the stiffness decreases slightly as angulation increases for axial compression and medio-lateral bending, increases slightly for torsion and increases substantially for antero-posterior bending.External fixator systems with curved acrylic connecting bars are commonly used in veterinary orthopaedics. This paper evaluates the biomechanical performance of such systems by applying the finite element analysis method. It shows that external fixators with curved acrylic connecting bars exhibit stiffness and maximal pin stresses which are similar to those of the standard stainless steel system.

F2-6 A Finite Element Analysis of Hydrogen Diffusion in a Stainless Steel Containing Strain-Induced Martensite

2009 ◽  
Vol 2009.22 (0) ◽  
pp. 270-271
Author(s):  
Reza Miresmaeili ◽  
Hirofumi Notsu ◽  
Takuya Nakagawa ◽  
Jean-Marc Olive ◽  
Masao Ogino ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Hydrogen Diffusion ◽  
Element Analysis ◽  
Strain Induced Martensite
Sign in / Sign up

Export Citation Format

Share Document