waste engine oil
Recently Published Documents


TOTAL DOCUMENTS

165
(FIVE YEARS 97)

H-INDEX

17
(FIVE YEARS 5)

2022 ◽  
Vol 2022 ◽  
pp. 1-12
Author(s):  
Yanbo Wang ◽  
Ailian Liu ◽  
Weixiang Ding ◽  
Fangping Rao ◽  
Jun Yuan ◽  
...  

This research explores the effects of using waste engine oil bottom on physical, rheological properties and composite modification mechanism of SBS-modified asphalt. The SBS asphalt binder was modified by WEOB with different concentrations (2, 4, and 6 wt%). The GC-MS and FTIR spectrometry were conducted to evaluate the chemical compositions of WEOB- and WEOB-modified asphalt. RV, DSR, and BBR were tested to evaluate high- and low-temperature pavement performance. Fluorescence microscope (FM) test, bar thin layer chromatograph (BTLC) test, and AFM test were performed to evaluate the micromorphologies and modification mechanism. The test results showed that a new characteristic peak appeared in the infrared spectrum of the WEOB-modified SBS asphalt, indicating a chemical reaction in the modification process. Incorporation of WEOB improves both the high-temperature and low-temperature properties of the SBS asphalt binder. It was confirmed that with the increase of WEOB concentration, the content of colloid gradually increases, which promotes the swelling and compaction of SBS polymer network structure. Furthermore, WEOB promotes the polarity of SBS and forms graft product MAH-g-SBS with asphalt, thus inhibiting the thermal movement of asphalt molecules. On the contrary, light components have a good correlation with the surface roughness of modified asphalt; the results show that the modified asphalt has good rutting resistance.


Author(s):  
Biruk Tadele ◽  
Emer T Quezon

Engineers have been using modified binders to improve the quality of flexible pavements. The use of waste material is one of the solutions taken in this direction. It is for this ground that the studies emphasis on the evaluation of waste engine oil as a modifier for asphalt binder as a pavement material. In the study uses four samples extracted from 80/100 penetration grade bitumen. From four sample first sample was checked for weather requirements of asphalt binder meet or not and the three were modified with different content of engine oil (3,6 and 9%). The behaviors of both unmodified and modified binder were checked for rheological properties. Dynamic shear rheometer (DSR) was used to determine high temperature performance grade (PG) and multiple stress creep recovery tests to determine rutting resistance properties of the binder. PG analysis indicates that both aged and un-aged 3% and 6% modified binder have similar higher PG grade with the unmodified one and 9% modified to have lower PG vale. Jnr3.2 value of modified asphalt binder is lower than unmodified binder indicating that modification had improved the rutting resistance and design traffic load (ESALS). The study shows that it is possible to use waste engine oil-modified binder as a pavement material.


Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 52
Author(s):  
Xue Xue ◽  
Junfeng Gao ◽  
Jiaqing Wang ◽  
Yujing Chen

This research aims to explore the high-temperature and low-temperature performances of lignin–waste engine oil-modified asphalt binder and its mixture. For this research, the lignin with two contents (4%, 6%) and waste engine oil with two contents (3%, 5%) were adopted to modify the control asphalt binder (PG 58-28). The high-temperature rheological properties of the lignin–waste engine oil-modified asphalt binder were investigated by the viscosity obtained by the Brookfield viscometer and the temperature sweep test by the dynamic shear rheometer. The low-temperature rheological property of the lignin–waste engine oil-modified asphalt binder was evaluated by the stiffness and m-value at two different temperatures (−18 °C, −12 °C) obtained by the bending beam rheometer. The high-temperature and the low-temperature performances of the lignin–waste engine oil-modified asphalt mixture were explored by the rutting test and low-temperature bending beam test. The results displayed that the rotational viscosity and rutting factor improved with the addition of lignin and decreased with the incorporation of waste engine oil. Adding the lignin into the control asphalt binder enhanced the elastic component while adding the waste engine oil lowered the elastic component of the asphalt binder. The stiffness of asphalt binder LO60 could not meet the requirement in the specification, but the waste engine oil made it reach the requirement based on the bending beam rheometer test. The waste engine oil could enhance the low-temperature performance. The dynamic stabilities of LO40- and LO60-modified asphalt mixture increased by about 9.05% and 17.41%, compared to the control mixture, respectively. The maximum tensile strain of LO45 and LO65 increased by 16.39% and 25.28% compared to that of LO40 and LO60, respectively. The high- and low-temperature performances of the lignin–waste engine oil-modified asphalt LO65 was higher than that of the control asphalt. The dynamic stability had a good linear relationship with viscosity, the rutting factor of the unaged at 58 °C, and the rutting factor of the aged at 58 °C, while the maximum tensile strain had a good linear relationship with m-value at −18 °C. This research provides a theoretical basis for the further applications of lignin–waste engine oil-modified asphalt.


Author(s):  
Ahmed Salama Eltwati ◽  
Mahmoud Enieb ◽  
Zaid H. Al-Saffar ◽  
Azman Mohamed

Forests ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1762
Author(s):  
Larisa Belchinskaya ◽  
Konstantin Viktorovich Zhuzhukin ◽  
Tatiana Ishchenko ◽  
Aleksey Platonov

Impregnation is a common method of protecting wood from external influences. This study proposes the use of spent engine oil as an impregnating composition for modifying birch wood to make it resistant to biological degradation and water. The indicators of water resistance and dimensional stability of wood such as wetting contact angle, thermogravimetric analysis, Fourier transform infrared spectroscopy (FTIR), and biodegradation tests have been determined. It has been found that treatment with spent engine oil significantly increases the dimensional stability (56.8% and 45.7% in tangential and radial directions) and water-resistant indicators of wood. Thermogravimetric analysis has showed that the curves for the impregnated specimens were different from the control group and had two sharp peaks at 302 and 357 °C. However, FTIR indicated that no clear chemical reactions occur between spent engine oil and wood. A study on wood resistance to biological degradation has showed a significant increase in resistance against brown rot (Poria placenta fungi) in the treated specimens, in contrast to the control group. Thus, impregnation of wood with spent engine oil makes it possible to increase wood resistance to water and biological degradation.


2021 ◽  
Vol 313 ◽  
pp. 125411
Author(s):  
Anqi Chen ◽  
Ziang Hu ◽  
Mingliang Li ◽  
Tao Bai ◽  
Guangjian Xie ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document