Fracture toughness and fractographic investigation of polybutylene terephthalate/thermoplastic polyurethane binary blends reinforced by multi-walled carbon nanotubes using essential work of fracture approach

In this paper, fracture toughness evaluation of polybutylene terephthalate (PBT)/thermoplastic polyurethane (TPU) binary blends and PBT/TPU/carbon nanotubes (CNTs) ternary nanocomposites have been conducted using both Izod impact and quasi-static fracture tests. Essential work of fracture (EWF) approach is used to study the fracture properties in details. The results of EWF tests revealed an effective role of TPU and CNTs in toughening mechanism of binary blends and ternary nanocomposites. According to EWF results, both the crack resistance and plastic deformation energies promoted in all compounds as compared to neat PBT. Energy dissipation in the yielding and tearing stages determined by the energy partitioning method. The obtained results indicated that displacement up to the failure point increased by increasing the TPU content, while inclusion of CNTs reduced this quantity. The specific non-essential work of fracture [Formula: see text] , [Formula: see text], and [Formula: see text] increased with increasing the TPU contents which is confirmed by load-displacement curves. Whereas, addition of CNTs reduced [Formula: see text] and [Formula: see text] values as compared to reference binary blend, however, ternary nanocomposites still have higher values as compared to pure PBT. In contrast with EWF results, high strain rate of impact test prevents the activation of toughness improving mechanisms that readily occurs in quasi-static loading.

Stiff-Elongated Balance of PLA-Based Polymer Blends

In this study, polymer blends with a mechanical property balance based on poly(lactic acid) (PLA), stiff polymer, and elongated polymer were developed. First, the binary blends PLA-elongated polymer [ethyl vinyl acetate (EVA) or polyethylene], or PLA-stiff polymer [polystyrene or poly(styrene-co-methyl methacrylate) (SMMA)] blends were studied using dynamic mechanic analysis (DMA) and analyzed using Minitab statistical software to determine the factors influencing the elongation or stiffness of the blends. Then, ternary blends such as elongation-poly(lactic acid)-stiff, were made from the binary blends that presented optimal performance. In addition, three blends [EVA–PLA–SMMA (EPS)] were elaborated by studying the mixing time (5, 15, and 15 min) and the added time of the SMMA (0, 0, and 10 min). Specifically, the mixing time for EPS 1, EPS 2, and EPS 3 is 5 min, 15 min, and 15 min (first EVA + PLA for 10 min, plus 5 min PLA-EVA and SMMA), respectively. Mechanical, thermal, rheological, and morphological properties of the blends were studied. According to DMA, the results show an increase in elongation at break (εb) and do not decrease the elastic module of poly(lactic acid). Nevertheless, EPS 3 excels in all properties, with an εb of 67% and modulus of elasticity similar to PLA. SMMA has a significant role as a compatibilizing agent and improves PLA processability.

Experimental Research on NO2 Viscosity and Absorption for (1-Ethyl-3-methylimidazolium Trifluoroacetate + Triethanolamine) Binary Mixtures

The viscosity (9.34–405.92 mPa·s) and absorption capacity (0.4394–1.0562 g·g−1) of (1-ethyl-3-methylidazolium trifluoroacetate + triethanolamine) binary blends atmospheric pressure in the temperature range of 303.15–343.15 K and at different mole fractions of [EMIM] [TFA] have been carried out. The molar fraction of [EMIM] [TFA] dependence of the viscosity and absorption capacity was demonstrated. The addition of a small amount of [EMIM] [TFA] into TEA led to rapidly decreased rates of binary blends’ viscosity and absorption capacity. However, the viscosity and absorption of binary blends did not decrease significantly when [EMIM] [TFA] was increased to a specific value. Compared with the molar fraction of the solution, the temperature had no obvious effect on viscosity and absorption capacity. By modeling and optimizing the ratio of viscosity and absorption capacity of ([EMIM] [TFA] + TEA), it is proven that when the mole fraction of [EMIM] [TFA] is 0.58, ([EMIM] [TFA] + TEA) has the best viscosity and absorption capacity at the same time. In addition, at 303.15 K, ([EMIM] [TFA] + TEA) was absorbed and desorbed six times, the absorption slightly decreased, and the desorption increased.

Cocoa butter equivalent from Kpangnan butter and Pequi oil

Novel cocoa butter equivalents were designed using dry fractionated Pequi oil and solvent fractionated Kpangnan butter. Static crystallization of binary mixtures of these two fractions into the triclinic form (β2) was achieved after 12 days for all mixtures and after 4 days for the 80:20 w/w and 90:10 w/w fractionated Kpangnan:Pequi oil mixtures. Moreover, after 60 days of storage at 22oC, all binary blends (except 100% fractionated pequi oil and 100% fractionated Kpangnan butter) were crystallized in the most stable triclinic crystal form (β1). Here we also discovered an unusual melting behavior for the fractionaled 30:70 w/w and 20:80 w/w fractionated Kpangnan:Pequi oil mixtures, where after 4 days of static crystallization at room 22oC, these mixtures displayed higher than predicted melting points, 41.89 oC and 33.32 oC, respectively. This suggested a faster kinetics of transformation to the triclinic β2 form for those mixtures. Our results suggest that the 30:70 w/w fractionated Kpangnan:Pequi oil mixture with a melting point of 34oC after 60 days storage at 22oC, a stable triclinic β2 form, and a triglyceride composition of 28% POP, 4.6% POS and 33% SOS displayed solid state characteristics, melting point and crystal structure, of a commercial cocoa butter equivalent.

Temperature glass and conductivity behavior of epoxy deproteinized natural rubber in ternary blend of EDPNR/PMMA/LiCF3SO3

The temperature glass behavior of epoxy deproteinized natural rubber/polymethylmethacrylate/lithium trifluoromethanesulfonate (EDPNR/PMMA/LiCF3SO3) and the conductivity behavior of EDPNR in the ternary blends were studied by DSC and multichannel potentiostat. The DSC result revealed the temperature glass of the EDPNR was shifted to the right with the increase of lithium salt amount in these binary blends composition. However, in the ternary blends of EDPNR/PMMA/LiCF3SO3 the temperature glass revealed the miscibility of these ternary blends. Two different temperature glass values were obtained when the ratio of EDPNR in EDPNR/PMMA was less than 80 wt.%. The ionic conductivity of EDPNR could be improved by increasing the amount of lithium salt up to 35 wt.%, after this amount the ionic conductivity of EDPNR was significantly decreased. While in the ternary blends, the highest ionic conductivity value was found at the ratio 80/20 of EDPNR/PMMA. Furthermore, the factors influencing the temperature glass and conductivity behavior of EDPNR were systematically studied in this work. The results demonstrated an intimate correlation between temperature glass and conductivity behavior of EDPNR.