Effectiveness of Using Polymer-Modified Asphalt Binders in Enhancing Fatigue Life of Asphalt Mixes Containing RAS and RAP

2021 ◽  
pp. 213-219
Author(s):  
Rouzbeh Ghabchi ◽  
Musharraf Zaman ◽  
Dharamveer Singh ◽  
Manik Barman ◽  
David L. Boeck
Keyword(s):  
Fatigue Life ◽  
Asphalt Binders ◽  
Asphalt Mixes ◽  
Modified Asphalt ◽  
Polymer Modified Asphalt

scholarly journals Mechanical Characteristics of Graphene Nanoplatelets-Modified Asphalt Mixes: A Comparison with Polymer- and Not-Modified Asphalt Mixes

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2434
Author(s):  
Laura Moretti ◽  
Nico Fabrizi ◽  
Nicola Fiore ◽  
Antonio D’Andrea
Keyword(s):  
Fatigue Resistance ◽  
Graphene Nanoplatelets ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Asphalt Mixes ◽  
Modified Asphalt ◽  
Bituminous Mixtures ◽  
Water Sensitivity ◽  
Polymer Modified Asphalt ◽  
Mechanical Performances

In recent years, nanotechnology has sparked an interest in nanomodification of bituminous materials to increase the viscosity of asphalt binders and improves the rutting and fatigue resistance of asphalt mixtures. This paper presents the experimental results of laboratory tests on bituminous mixtures laid on a 1052 m-long test section built in Rome, Italy. Four asphalt mixtures for wearing and binder layer were considered: two polymer modified asphalt concretes (the former modified with the additive Superplast and the latter modified with styrene–butadiene–styrene), a “hard” graphene nanoplatelets (GNPs) modified asphalt concrete and a not-modified mixture. The indirect tensile strength, water sensitivity, stiffness modulus, and fatigue resistance of the mixtures were tested and compared. A statistical analysis based on the results has shown that the mixtures with GNPs have higher mechanical performances than the others: GNP could significantly improve the tested mechanical performances; further studies will be carried out to investigate its effect on rutting and skid resistance.

scholarly journals Material Properties and Environmental Benefits of Hot-Mix Asphalt Mixes Including Local Crumb Rubber Obtained from Scrap Tires

Environments ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 47
Author(s):  
Lim Min Khiong ◽  
Md. Safiuddin ◽  
Mohammad Abdul Mannan ◽  
Resdiansyah
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Environmental Benefits ◽  
Asphalt Binders ◽  
Rubber Content ◽  
Scrap Tires ◽  
Asphalt Mixes ◽  
Temperature Resistance ◽  
Modified Asphalt ◽  
Marshall Stability

This paper presents the results of a laboratory-based experimental investigation on the properties of asphalt binder and hot-mix asphalt (HMA) mixes modified by locally available crumb rubber, which was used as a partial replacement of asphalt by weight. In this study, fine crumb rubber with a particle size in the range of 0.3–0.6 mm, obtained from scrap tires, was added to the asphalt binder through the wet process. Crumb rubber contents of 5%, 10%, 15%, and 19% by weight of asphalt were added to the virgin binder in order to prepare the modified asphalt binder samples, while the unmodified asphalt binder was used as the control sample. The crumb rubber modified binder samples were examined for measuring viscosity indirectly using the penetration test, and temperature resistance using the softening point test. Later, both the modified and unmodified asphalt binders were used to produce HMA mixes. Two categories of HMA mix commonly used in Malaysia—namely, AC 14 (dense-graded) and SMA 14 (gap-graded)—were produced using the modified asphalt binders containing 5%, 10%, 15%, and 19% crumb rubber. Two AC 14 and SMA 14 control mixes were also produced, incorporating the unmodified asphalt binder (0% crumb rubber). All of the AC 14 and SMA 14 asphalt mixes were examined in order to determine their volumetric properties, such as bulk density, voids in total mix (VTM), voids in mineral aggregate (VMA), and voids filled with asphalt (VFA). In addition, the Marshall stability, Marshall flow, and stiffness of all of the AC 14 and SMA 14 mixes were determined. Test results indicated that the modified asphalt binders possessed higher viscosity and temperature resistance than the unmodified asphalt binder. The viscosity and temperature resistance of the asphalt binders increased with the increase in their crumb rubber content. The increased crumb rubber content also led to improvements in the volumetric properties (bulk density, VTM, VMA, and VFA) of the AC 14 and SMA 14 mixes. In addition, the performance characteristics of the AC 14 and SMA 14 mixes—such as Marshall stability, Marshall flow, and stiffness—increased with the increase in crumb rubber content. However, the AC 14 mixes performed much better than the SMA 14 mixes. The overall research findings suggest that crumb rubber can be used to produce durable and sustainable HMA mixes, with manifold environmental benefits, for use in flexible pavements carrying the heavy traffic load of highways.

scholarly journals Impact of Graphene Oxide on Zero Shear Viscosity, Fatigue Life and Low-Temperature Properties of Asphalt Binder

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3073
Author(s):  
Abbas Mukhtar Adnan ◽  
Chaofeng Lü ◽  
Xue Luo ◽  
Jinchang Wang
Keyword(s):  
Graphene Oxide ◽  
Fatigue Life ◽  
Low Temperature ◽  
Shear Viscosity ◽  
Storage Stability ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Test Results ◽  
Zero Shear Viscosity ◽  
Modified Asphalt

This study has investigated the impact of graphene oxide (GO) in enhancing the performance properties of an asphalt binder. The control asphalt binder (60/70 PEN) was blended with GO in contents of 0%, 0.5%, 1%, 1.5%, 2%, and 2.5%. The permanent deformation behavior of the modified asphalt binders was evaluated based on the zero shear viscosity (ZSV) parameter through a steady shear test approach. Superpave fatigue test and the linear amplitude sweep (LAS) method were used to evaluate the fatigue behavior of the binders. A bending beam rheometer (BBR) test was conducted to evaluate the low-temperature cracking behavior. Furthermore, the storage stability of the binders was investigated using a separation test. The results of the ZSV test showed that GO considerably enhanced the steady shear viscosity and ZSV value, showing a significant contribution of the GO to the deformation resistance; moreover, GO modification changed the asphalt binder’s behavior from Newtonian to shear-thinning flow. A notable improvement in fatigue life was observed with the addition of GO to the binder based on the LAS test results and Superpave fatigue parameter. The BBR test results revealed that compared to the control asphalt, the GO-modified binders showed lower creep stiffness (S) and higher creep rate (m-value), indicating increased cracking resistance at low temperatures. Finally, the GO-modified asphalt binders exhibited good storage stability under high temperatures.

A critical review of high polymer-modified asphalt binders and mixtures

2018 ◽  
Vol 21 (6) ◽  
pp. 686-702 ◽  
Author(s):  
Jhony Habbouche ◽  
Elie Y. Hajj ◽  
Peter E. Sebaaly ◽  
Murugaiyah Piratheepan
Keyword(s):  
Critical Review ◽  
Asphalt Binders ◽  
High Polymer ◽  
Modified Asphalt ◽  
Polymer Modified Asphalt

Effects of warm mix asphalt additives on performance properties of polymer modified asphalt binders

2010 ◽  
Vol 37 (1) ◽  
pp. 17-24 ◽  
Author(s):  
Hakseo Kim ◽  
Soon-Jae Lee ◽  
Serji N. Amirkhanian
Keyword(s):  
Fatigue Cracking ◽  
Warm Mix Asphalt ◽  
Asphalt Binders ◽  
Rotational Viscometer ◽  
Performance Properties ◽  
Modified Asphalt ◽  
Positive Effects ◽  
Performance Grade ◽  
Low Temperature Cracking ◽  
Polymer Modified Asphalt

This study presents an experimental evaluation for the performance properties of polymer modified asphalt (PMA) binders containing warm mix asphalt (WMA) additives. The PMA binders with the additives were produced using two of the available warm asphalt processes (i.e., Aspha-min and Sasobit) and three PMA binders graded as performance grade (PG) 76-22. The warm PMA binders were artificially short-term and then long-term aged using the rolling thin film oven (RTFO) and pressure aging vessel (PAV) procedures. Superpave binder tests were carried out on the binders through the rotational viscometer (RV), the dynamic shear rheometer (DSR), and the bending beam rheometer (BBR). In general, the results of this research indicated that (1) the addition of the WMA additives into the PMA binders showed positive effects on increasing rutting resistance at high temperature (based on the high failure temperature values from the DSR test); (2) the PMA binders containing the additives were observed to be less resistant to fatigue cracking at intermediate temperatures compared to the control PMA binders (based on the G*sin δ values at 25 °C from the DSR test); and (3) the addition of wax additive represented a possible lower resistance on low temperature cracking (based on the stiffness and the m-value at –12 °C from the BBR test).

Sign in / Sign up

Export Citation Format

Share Document