Impact and Effect Study of Submerged-Arc Welding Conditions on Structural Changes in Weld Metal

2021 ◽  
pp. 65-76
Author(s):  
Pavel V. Bakhmatov ◽  
Egor A. Startsev ◽  
Boris M. Sobolev
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Structural Changes ◽  
Effect Study ◽  
Submerged Arc Welding ◽  
Submerged Arc

scholarly journals Research of nanoscale titanium carbides influence on the structure and properties of weld metal in automatic submerged arc welding

2018 ◽  
Vol 226 ◽  
pp. 03029
Author(s):  
Nikolay V. Kobernik ◽  
Alexander S. Pankratov
Keyword(s):  
Titanium Carbide ◽  
Weld Metal ◽  
Weld Pool ◽  
Arc Welding ◽  
Submerged Arc Welding ◽  
Structure And Properties ◽  
Cored Wire ◽  
Average Value ◽  
Submerged Arc ◽  
Primary Crystals

The influence of nanoscale refractory titanium carbide particles on the structure and properties of weld metal in automatic submerged arc welding is considered. Composite granules based on nickel were used to introduce the compound into the composition of the weld pool. Two schemes for introducing granules into the weld pool were tested, characterized by different temperature conditions: to the head part of the welding pool with the help of “ligature” and to the tail section with the help of additional filler wire. The prospects of introducing nano-sized titanium carbide into the tail part of the weld pool as part of a flux-cored wire are shown. With this method, the structure of the weld metal is observed to modify: the average size of the primary crystals of the weld metal is reduced by almost 50%. At the same time, the value of the toughness of the weld metal increases: the average value of this index increases by 36%. When titanium carbide is introduced as part of the “ligature” into the head of the weld pool, despite the effect of modifying (reducing the width of the primary crystals by 30%), the average value of the toughness of the weld metal decreases.

scholarly journals Erratum to: Modification of Weld Metal with Tungsten Carbide and Titanium Nitride Nanoparticles in Twin Submerged Arc Welding

2019 ◽  
Vol 53 (2) ◽  
pp. 176-176
Author(s):  
N. P. Aleshin ◽  
M. V. Grigor’ev ◽  
N. V. Kobernik ◽  
R. S. Mikheev ◽  
A. S. Pankratov ◽  
...  
Keyword(s):  
Weld Metal ◽  
Titanium Nitride ◽  
Tungsten Carbide ◽  
Arc Welding ◽  
Submerged Arc Welding ◽  
Submerged Arc

Modification of Weld Metal with Tungsten Carbide and Titanium Nitride Nanoparticles in Twin Submerged Arc Welding

2018 ◽  
Vol 52 (5) ◽  
pp. 440-445
Author(s):  
N. P. Aleshin ◽  
M. V. Grigor’ev ◽  
N. V. Kobernik ◽  
R. S. Mikheev ◽  
A. S. Pankratov ◽  
...  
Keyword(s):  
Weld Metal ◽  
Titanium Nitride ◽  
Tungsten Carbide ◽  
Arc Welding ◽  
Submerged Arc Welding ◽  
Submerged Arc

Investigation on Deposited Metal Properties of Homemade Nickel and Nickel-Free Electrodes and Fluxes for Submerged Arc Welding of SA-508 Gr.3 Cl.1

2017 ◽  
Author(s):  
Le Mei ◽  
Junbao Zhang ◽  
Yifeng Huang ◽  
Yan Yu ◽  
Yong Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Weld Metal ◽  
Arc Welding ◽  
Proton Irradiation ◽  
Submerged Arc Welding ◽  
Impact Property ◽  
Welding Material ◽  
Weld Metals ◽  
Metal Properties ◽  
Submerged Arc

Up to now, two kinds of filler metal with or without nickel element for submerged arc welding have been largely used in the reactor pressure vessel (RPV) manufacturing. In order to study the effect of nickel element on weld metal properties of SA-508 Gr.3 Cl.1, submerged arc welding material with nickel (AWS classification F8P4-EGN-F2N, F2 for short) and welding material without nickel (F8P4-EA3N-A3N, A3 for short) were used; and conventional mechanical properties, low-cycle fatigue test, and proton irradiation analysis of the two weld metals were studied. Results show that the mechanical properties of the two different weld metals are similar, except that the Charpy V-notch impact property of the weld metal with nickel is better than that without nickel; the micro-structures of F2 and A3 weld metals are both composed of ferrite base and granular bainite, but the columnar grain size of F2 weld metal is smaller relatively, which results in better impact property. In addition, the irradiated A3 weld metal has fewer dislocation loops than the irradiated F2 weld metal after the same proton irradiation dose; the irradiated weld metals both have higher micro-Vickers hardness than before.

TMF Influence on Weld Structure at the Welding of 12X18H9T

2018 ◽  
Vol 927 ◽  
pp. 1-5 ◽  
Author(s):  
Alexander D. Razmyshlyaev ◽  
Marina V. Ahieieva ◽  
Elena V. Lavrova
Keyword(s):  
Magnetic Field ◽  
Weld Metal ◽  
Arc Welding ◽  
Welding Process ◽  
Metal Structure ◽  
Transverse Magnetic ◽  
Submerged Arc Welding ◽  
Structural Components ◽  
Weld Structure ◽  
Submerged Arc

The transverse magnetic field (TMF) use allows to obtain follow effects: increasing the electrode melting coefficient, reducing the base metal penetration depth and grinding the weld metal structural components. The paper analyzed the existing literature data about the TMF influence on the refinement of the weld metal structure. It is experimentally shown that the alternating TMF influence of 6 Hz frequency reduces the grain size of weld metal is almost twice in comparison with the welding process without the TMF influence at submerged arc welding of plates of austenitic steel type 12X18H9T (X10CrNiTi18-9). The average grains size is 7-6 index, when welding without the TMF influence and the average grains size of the weld metal corresponds to 8 index, with separate inclusions of grains with 7 index when welding with the TMF influence. This is should increase the yield strength value of the weld metal in accordance with the data of Hall – Petch.

scholarly journals Reactions at the molten flux-weld pool interface in submerged arc welding

2021 ◽  
Vol 40 (1) ◽  
pp. 421-427
Author(s):  
Theresa Coetsee ◽  
Frederik De Bruin
Keyword(s):  
Weld Metal ◽  
Weld Pool ◽  
Arc Welding ◽  
Oxygen Potential ◽  
Base Plate ◽  
Submerged Arc Welding ◽  
Welding Flux ◽  
Molten Flux ◽  
Powder Addition ◽  
Submerged Arc

Abstract In submerged arc welding (SAW) of chromium (Cr) containing steels, Cr is usually added to the weld metal from the weld wire, and not from the welding flux. Manufacturing of weld wires of specific compositions is expensive and time consuming and cannot closely match all the desired alloy compositions. Therefore, the weld wire chemistry is usually over matched to the base plate composition. Better matching between the weld metal and base plate is possible if the weld metal incorporates Cr from Cr containing metal powder, instead of sourcing Cr from weld wire of limited Cr content. Because Cr is easily oxidised, the oxygen partial pressure in SAW must be controlled. This work illustrates the control of the oxygen potential at the molten flux-weld pool interface by using aluminium (Al) powder addition. The controlled oxygen potential at the molten flux-weld pool interface ensures increased Cr powder transfer into the weld pool, without interfering with oxygen transfer from the plasma arc to the weld pool. The objective of this work is to use targeted powder additions to better control Cr reactions in SAW to improve Cr metal transfer to the weld metal and maintain an acceptable level of oxygen in the weld metal.

Some Feasibility Studies for Recycling of Steel Slag as a Useful Flux for Submerged Arc Welding

2020 ◽  
Vol 19 (02) ◽  
pp. 277-289
Author(s):  
Sumit Saini ◽  
Kulwant Singh
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Steel Slag ◽  
Welding Process ◽  
Feasibility Studies ◽  
Submerged Arc Welding ◽  
Bead Geometry ◽  
Weld Bead Geometry ◽  
Arc Welding Process ◽  
Submerged Arc

Protection of environment from industrialization and urbanization waste is the prime duty of engineers and researchers. Elimination of industrial waste completely is not possible because it is generally a byproduct of the process. It can be minimized by recycling or reusing. In this research, waste slag generated by steel plant is recycled as a useful flux for submerged arc welding. It is found that recycled slag is capable of producing acceptable weld bead geometry. The penetration achieved using recycled slag is 7.897[Formula: see text]mm, which is more than the penetration obtained using fresh flux, i.e. 6.027[Formula: see text]mm. The reinforcement produced by recycled slag is 2.632[Formula: see text]mm, which is close to the reinforcement obtained using fresh flux. It is further observed that chemistry of weld metal deposited using recycled slag is also at par with that of weld metal produced using fresh original flux. The amount of carbon present in weld metal produced by recycled slag is 0.15%, which is comparable to the percentage of carbon present in weld metal produced using fresh flux. The microstructure and microhardness obtained using recycled slag are also comparable with the microstructure and microhardness obtained using fresh flux. This research established the feasibility of recycling slag as a flux required for submerged arc welding process.

Development of Welding Procedures for X90-Grade Seamless Pipes for Riser Applications

2012 ◽  
Author(s):  
Hiroyuki Nagayama ◽  
Masahiko Hamada ◽  
Mark F. Mruczek ◽  
Mark Vickers ◽  
Nobuyuki Hisamune ◽  
...  
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Mechanical Test ◽  
Welding Process ◽  
High Strength ◽  
Submerged Arc Welding ◽  
Welding Parameters ◽  
Flux Cored Arc Welding ◽  
Welding Procedure ◽  
Submerged Arc

Ultra-high strength seamless pipes of X90 and X100 grades have been developed for deepwater or ultra-deepwater applications. Girth welding procedure specifications (WPSs) should be developed for the ultra-high strength pipes. However, there is little information for double jointing welding procedure by using submerged arc welding process for high strength line pipes. This paper describes mechanical test results of submerged arc welding (SAW) and gas shielded flux cored arc welding (GSFCAW) trials with various welding consumables procured from commercial markets. Welds were then made with typical welding parameters for riser productions using high strength X90 seamless pipes. The submerged arc weld metal strength could increase by increasing alloy elements in weld metal. The weld metal with CE (IIW) value of 0.74 mass% achieved fully overmatching for the X90 pipe. The weld metal yield strength (0.2% offset) was 694 MPa, and the ultimate tensile strength was 833 MPa. It was also confirmed that the reduction of boron in weld metal can improve low temperature toughness of high strength weld metal. Furthermore, it was confirmed that the HAZ has excellent mechanical properties and toughness for riser applications. In this study GSFCAW procedures were also developed. GSFCAW can be used for joining pipe and connector material for riser production welding. The weld metal with a CE (IIW) value of 0.54 mass% could meet the required strength level for X90-grade pipe as specified in ISO 3183. Cross weld tensile testing showed that fractures were achieved in the base metal. Good Charpy impact properties in weld metal and HAZ were also confirmed.

Sign in / Sign up

Export Citation Format

Share Document