Improvement of aerodynamic performance of a low speed axial compressor rotor blade row through air injection

2018 ◽  
Vol 72 ◽  
pp. 409-417 ◽  
Author(s):  
Reza Taghavi-Zenouz ◽  
Mohammad Hosein Ababaf Behbahani
Keyword(s):  
Rotor Blade ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Air Injection ◽  
Low Speed ◽  
Compressor Rotor ◽  
Blade Row

Experimental investigation on flow unsteadiness during spike stall suppression process in an axial compressor via air injection

2016 ◽  
Vol 231 (14) ◽  
pp. 2677-2688 ◽  
Author(s):  
R Taghavi Zenouz ◽  
MH Ababaf Behbahani ◽  
F Rousta ◽  
A Khoshnejad
Keyword(s):  
Flow Rate ◽  
Rotor Blade ◽  
Performance Enhancement ◽  
Axial Compressor ◽  
Recovery Process ◽  
Air Injection ◽  
Stall Inception ◽  
Stall Margin ◽  
Beneficial Effects ◽  
Blade Row

Stall recovery process for performance enhancement of an axial compressor has been experimentally carried out using air injection at its rotor blade row tip region. Twelve air injectors had been mounted evenly spaced around the compressor casing upstream the rotor blade row. Instantaneous flow velocities at various radial and circumferential positions were measured simultaneously utilizing hot wire anemometry. These unsteady results, separately presented in frequency and time domains, provided to distinguish stall inception process and consequent flow induced fluctuations. Time-dependent responses of the flow field properties within the compressor passage and progressive alleviation of stall cells are demonstrated during the tip injection process. Blade tip air injection worked effectively and enhanced the compressor stall margin about 9%. This attractive result occurred for the case where the total mass flow rate passing through the air injectors was as small as 0.8% of the compressor main flow rate. In addition, this augmentation in the stall margin was accompanied by increase in the compressor delivery total pressure. Air injection at the blade row tip region caused its beneficial effects to extend throughout the blade whole span, especially while working at the near-stall conditions.

scholarly journals Performance of a Low Speed Axial Compressor Rotor Blade Row under Different Inlet Distortions

2017 ◽  
Vol 8 (1) ◽  
pp. 127-136 ◽  
Author(s):  
Reza Taghavi Zenouz ◽  
Mehran Eshaghi Sir ◽  
Mohammad Hosein Ababaf Behbahani
Keyword(s):  
Rotor Blade ◽  
Fluid Dynamic ◽  
Axial Compressor ◽  
Main Flow ◽  
Flow Simulations ◽  
Compressor Rotor ◽  
Dynamic Technique ◽  
Performance Curves ◽  
Blade Row ◽  
Compressor Design

Abstract. Responses of an axial compressor isolated rotor blade row to various inlet distortions have been investigated utilizing computational fluid dynamic technique. Distortions have been imposed by five screens of different geometries, but with the same blockage ratio. These screens were embedded upstream of the rotor blade row. Flow fields are simulated in detail for compressor design point and near stall conditions. Performance curves for distorted cases are extracted and compared to the undisturbed case. Flow simulations and consequent performance characteristics show that the worst cases belong to non-symmetric blockages, i.e., those of partial circumferential configurations. These cases produce the largest wakes which can disturb the flow, considerably. Superior performances correspond to the inner and outer continuous circumferential distortion screens. Since, they produce no significant disturbances to the main flow in comparison to the non-symmetric screens.

Cold Blade Profile Generation Methodology for Compressor Rotor Blades Using FSI Approach

2017 ◽  
Author(s):  
Kirubakaran Purushothaman ◽  
Sankar Kumar Jeyaraman ◽  
Ajay Pratap ◽  
Kishore Prasad Deshkulkarni
Keyword(s):  
Aspect Ratio ◽  
Rotor Blade ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Blade Profile ◽  
Interaction Technique ◽  
Compressor Rotor ◽  
Blade Shape ◽  
Blade Geometry

This paper describes a methodology for obtaining correct blade geometry of high aspect ratio axial compressor blades during running condition taking into account of blade untwist and bending. It discusses the detailed approach for generating cold blade geometry for axial compressor rotor blades from the design blade geometry using fluid structure interaction technique. Cold blade geometry represents the rotor blade shape at rest, which under running condition deflects and takes a new operating blade shape under centrifugal and aerodynamic loads. Aerodynamic performance of compressor primarily depends on this operating rotor blade shape. At design point it is expected to have the operating blade shape same as the intended design blade geometry and a slight mismatch will result in severe performance deterioration. Starting from design blade profile, an appropriate cold blade profile is generated by applying proper lean and pre-twist calculated using this methodology. Further improvements were carried out to arrive at the cold blade profile to match the stagger of design profile at design operating conditions with lower deflection and stress for first stage rotor blade. In rear stages, thermal effects will contribute more towards blade deflection values. But due to short blade span, deflection and untwist values will be of lower values. Hence difference between cold blade and design blade profile would be small. This methodology can especially be used for front stage compressor rotor blades for which aspect ratio is higher and deflections are large.

A Comparison Between the Design Point and Near-Stall Performance of an Axial Compressor

1990 ◽  
Vol 112 (1) ◽  
pp. 109-115 ◽  
Author(s):  
N. M. McDougall
Keyword(s):  
Rotor Blade ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Design Point ◽  
Blade Row ◽  
Clearance Flow ◽  
Stator Blade

Detailed measurements have been made within an axial compressor operating both at design point and near stall. Rotor tip clearance was found to control the performance of the machine by influencing the flow within the rotor blade passages. This was not found to be the case in the stator blade row, where hub clearance was introduced beneath the blade tips. Although the passage flow was observed to be altered dramatically, no significant changes were apparent in the overall pressure rise or stall point. Small tip clearances in the rotor blade row resulted in the formation of corner separations at the hub, where the blade loading was highest. More representative clearances resulted in blockage at the tip due to the increased tip clearance flow. The effects that have been observed emphasize both the three-dimensional nature of the flow within compressor blade passages, and the importance of the flow in the endwall regions in determining the overall compressor performance.

A Stochastic Model for a Compressor Stability Measure

2006 ◽  
Vol 129 (3) ◽  
pp. 730-737 ◽  
Author(s):  
Manuj Dhingra ◽  
Yedidia Neumeier ◽  
J. V. R. Prasad ◽  
Andrew Breeze-Stringfellow ◽  
Hyoun-Woo Shin ◽  
...  
Keyword(s):  
Stochastic Model ◽  
High Speed ◽  
Stability Boundary ◽  
Model Development ◽  
Axial Compressor ◽  
Advanced Technology ◽  
Low Speed ◽  
Stability Measure ◽  
Compressor Rotor ◽  
The Impact

A stability measure rooted in the unsteady characteristics of the flow field over the compressor rotor has been previously developed. The present work explores the relationship between the stochastic properties of this measure, called the correlation measure, and the compressor stability boundary. A stochastic model has been developed to gauge the impact of the correlation measure’s stochastic nature on its applicability to compressor stability management. The genesis of this model is in the fundamental properties of a specific stochastic process, one that is created by the threshold crossings of a random process. The model validation utilizes data obtained on three different axial compressor facilities. These include a single-stage low-speed axial compressor, a four-stage low-speed research compressor, and an advanced technology demonstrator high-speed compressor. This paper presents details of the model development and validation, as well as closed loop experimental results to demonstrate correlation measure’s usefulness in compressor stability management.

scholarly journals Active flow control at a 1.5-stage low-speed research compressor with varying rotor tip clearance

2011 ◽  
Vol 225 (7) ◽  
pp. 886-896 ◽  
Author(s):  
M Künzelmann ◽  
R Urban ◽  
R Mailach ◽  
K Vogeler
Keyword(s):  
Flow Control ◽  
Active Flow Control ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Low Speed ◽  
Operating Range ◽  
Compressor Rotor ◽  
Active Flow

The stable operating range of axial compressors is limited by the onset of rotating stall and surge. Mass injection upstream of the tip of an axial compressor rotor is a stability enhancement approach which can be effective in suppressing stall in tip-critical rotors, and thus increasing the operating range of compressors. In this article, investigations on active flow control related to the rotor tip gap sensitivity are discussed. The experiments were performed in a 1.5-stage low-speed research compressor. Measurements at part speed (80 per cent) and full speed (100 per cent) with varying injection rates are discussed. These tests were performed for two rotor tip clearances of 1.3 per cent and 4.3 per cent of rotor blade tip chord. Results on the compressor map, the flow field as well as transient measurements to identify the stall inception are discussed. Supplementary, the numerical results are compared to the experiments based on the configuration with the greatest benefit in operating range enhancement.

Effect of Rotor Tip Gap Variation at the Rear Stages of an Axial Flow Compressor

2012 ◽  
Vol 225 ◽  
pp. 233-238
Author(s):  
A.M. Pradeep ◽  
R.N. Chiranthan ◽  
Debarshi Dutta ◽  
Bhaskar Roy
Keyword(s):  
Rotor Blade ◽  
Cross Flow ◽  
Axial Compressor ◽  
Axial Flow ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Suction Surface ◽  
Design Point ◽  
Compressor Rotor ◽  
Multi Stage

In this paper, detailed analysis of the tip flow of an axial compressor rotor blade has been carried out using the commercial CFD package ANSYS CFX. The rotor blade was designed such that it is reminiscent of the rear stages of a multi-stage axial compressor. The effects of varying tip gaps are studied using CFD simulations for overall pressure rise and flow physics of the tip flow at the design point and near the peak pressure point. Rig tests of a low speed research compressor rotor with 3% tip clearance provided characteristics plots for validation of the CFD results. With increase in clearance from 1% to 4%, the rotor pressure rise at the design point was observed to decrease linearly. Increase in the clearance increases the cross flow across the tip; however, the magnitude of the average jet velocity crossing the tip decreases. The tip leakage vortex was observed to stay close to the suction surface with increase in clearance.

Sign in / Sign up

Export Citation Format

Share Document