Bulk modulus and thermal expansion coefficient of mechano-chemically synthesized Mg2FeH6 from high temperature and high pressure studies

2009 ◽  
Vol 34 (8) ◽  
pp. 3410-3416 ◽  
Author(s):  
Lyci George ◽  
Vadym Drozd ◽  
Andriy Durygin ◽  
Jiuhua Chen ◽  
Surendra K. Saxena
Author(s):  
Jianhua Yu ◽  
Huayu Zhao ◽  
Shunyan Tao ◽  
Xiaming Zhou ◽  
Chuanxian Ding

Plasma-sprayed thermal barrier coating (TBC) systems are widely used in gas turbine blades to increase turbine entry temperature (TET) and better efficiency. Yttria stabilized zirconia (YSZ) has been the conventional thermal barrier coating material because of its low thermal conductivity, relative high thermal expansion coefficient and good corrosion resistance. However the YSZ coatings can hardly fulfill the harsh requirements in future for higher reliability and the lower thermal conductivity at higher temperatures. Among the interesting TBC candidates, materials with pyrochlore structure show promising thermo-physical properties for use at temperatures exceeding 1200 °C. Sm2Zr2O7 bulk material does not only have high temperature stability, sintering resistance but also lower thermal conductivity and higher thermal expansion coefficient. The sintering characteristics of ceramic thermal barrier coatings under high temperature conditions are complex phenomena. In this paper, samarium zirconate (Sm2Zr2O7, SZ) powder and coatings were prepared by solid state reaction and atmosphere plasma spraying process, respectively. The microstructure development of coatings derived from sintering after heat-treated at 1200–1500 °C for 50 h have been investigated. The microstructure was examined by scanning electron microscopy (SEM) and the grain growth was analyzed in this paper as well.


1998 ◽  
Vol 54 (6) ◽  
pp. 741-749 ◽  
Author(s):  
M. Catti ◽  
A. Pavese

A two-body interatomic potential function, including fractional atomic charges and a shell model for oxygen, and supplemented by an O—Al—O bond-angle energy term, was fitted to the structural, elastic and vibrational properties of \alpha-Al2O3, corundum, at ambient conditions. Full quasi-harmonic calculations were then carried out on a p,T grid of 54 points in the domain 0–40 GPa and 300–1700 K. The crystal structure was equilibrated at each point, taking into account the anisotropy of vibrational pressure and the thermal dependence of elastic constants, so as to obtain unit-cell edges, atomic coordinates, bulk modulus, thermal expansion coefficient and other thermodynamic properties. Polynomial approximations were developed to represent the p,T dependence of these quantities. Comparison with experimental results for the separate p (T = 300 K) and T (p = 0) behaviours shows very good agreement, with average deviations of 0.1% for the unit-cell volume and 6% for the thermal expansion coefficient. The coupled p,T dependence of the properties of corundum is predicted to be very small for the bulk modulus (\partial^2K_T/\partial p\partial T=8.4\times10^{-5} K−1), but not at all negligible for the volume [(1/V)\partial^2V/\partial p\partial T in the range −1.2 to −7.5 × 10−7 GPa−1 K−1 over the p,T domain explored].


Author(s):  
Jia Xiao ◽  
Zhijun Li ◽  
Li Jiang ◽  
Linfeng Ye ◽  
Kun Yu ◽  
...  

Abstract Two Alloy N/316H bimetallic plates have been fabricated by explosive welding and rolling technologies respectively. Metallographic observations indicate that the rolled bimetallic plate has a straight bond interface, in which some cavities and precipitates exist. While the explosive welded plate shows a wavy bond interfaces. The interface thermal expansion mismatch between the two alloys were evaluated in the two plates at high temperature. Results show that the thermal expansion coefficient of 316H is larger than that of Alloy N. The thermal expansion coefficient of the substrate plates depends on the thickness ratio between Alloy N and 316H, which reaches the maximum when the ratio is 1:4.


2020 ◽  
Vol 993 ◽  
pp. 771-775
Author(s):  
Ping Zhai ◽  
Xiao Feng Duan ◽  
Da Qian Chen

In this paper, zirconium tungstate ceramic with negative thermal expansion coefficients was prepared from zirconium oxide and tungstic acid by solid phase synthesis and high temperature quenching technique with a sintering temperature of 1200 °C. The phase structure of the material was determined by X ray and the thermal expansion coefficient was measured by dilatometer, while the TG-DTA analysis of the prepared material was also carried out. The results showed that zirconium tungstate with high purity could be obtained by rapid chilled while fired at 1200 °C. The coefficient of thermal expansion at 300 °C was minus 8.5413 × 10-6K-1, which is identical with the theoretical value. The thermal expansion coefficient of the material was negative fired lower than 750 °C, while it was positive fired higher than 750 °C, and this indicates that the decomposition temperature of zirconium tungstate is about 750 °C.


2003 ◽  
Vol 9 (1) ◽  
pp. 45-51
Author(s):  
Darius Zabulionis ◽  
Gediminas Marčiukaitis

Thermal strain is one of the factors causing additional stresses in a composite structure. It is necessary to calculate the coefficient of thermal expansion in evaluating thermal strains. According to the research, concrete is a material consisting of three phases: aggregate, interfacial transition zone (ITZ) and cement paste. The article presents the technique which enables the estimation of the thermal expansion coefficient of the mortar consisting of various aggregate fractions and covered with ITZ layer. A parametric study of various ITZ layer characteristics influencing the coefficient of thermal expansion has been carried out in the present paper. It has been determined that dry mortar or concrete could be treated as a material consisting of two components. While evaluating moist mortar or concrete it is necessary to take into account the depth of the ITZ the bulk modulus and the coefficient of thermal expansion.


Sign in / Sign up

Export Citation Format

Share Document