On the wave structure of the wall region of a turbulent boundary layer

1975 ◽  
Vol 70 (2) ◽  
pp. 229-250 ◽  
Author(s):  
Fritz H. Bark
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Reynolds Stress ◽  
Large Scale ◽  
Joint Probability Distribution ◽  
Wall Region ◽  
Time And Space ◽  
Mean Velocity ◽  
Model Calculations ◽  
Random System

Following the ideas suggested by Landahl (1967, 1975), some model calculations of the fluctuating velocity field in the wall region of a turbulent boundary layer have been carried out. It was assumed that the turbulent stresses are generated intermittently on small scales in time and space owing to bursting-type motions. The Reynolds-stress distribution during bursting periods and the mean velocity profile were assumed to be known, and the linear large-scale response to a random system of bursts was computed using an idealized model for the joint probability distribution in time and space of the occurrence of bursts. Computed energy spectra of the streamwise velocity fluctuations display scales in the spanwise and streamwise directions and time which are in good agreement with measurements by Morrison, Bullock & Kronauer (1971). However, the wavenumber band-widths of the computed spectra are narrower than those of the measured ones. This discrepancy is probably due to the crudeness of the model employed for the Reynolds stress during bursting.

scholarly journals Active control of multiscale features in wall-bounded turbulence

2019 ◽  
Vol 36 (1) ◽  
pp. 12-21 ◽  
Author(s):  
Xiaotong Cui ◽  
Nan Jiang ◽  
Xiaobo Zheng ◽  
Zhanqi Tang
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Streamwise Velocity ◽  
Discrete Wavelet ◽  
Wall Region ◽  
Mean Velocity ◽  
Pzt Actuator ◽  
The Impact ◽  
Near Wall

Abstract This study experimentally investigates the impact of a single piezoelectric (PZT) actuator on a turbulent boundary layer from a statistical viewpoint. The working conditions of the actuator include a range of frequencies and amplitudes. The streamwise velocity signals in the turbulent boundary layer flow are measured downstream of the actuator using a hot-wire anemometer. The mean velocity profiles and other basic parameters are reported. Spectra results obtained by discrete wavelet decomposition indicate that the PZT vibration primarily influences the near-wall region. The turbulent intensities at different scales suggest that the actuator redistributes the near-wall turbulent energy. The skewness and flatness distributions show that the actuator effectively alters the sweep events and reduces intermittency at smaller scales. Moreover, under the impact of the PZT actuator, the symmetry of vibration scales’ velocity signals is promoted and the structural composition appears in an orderly manner. Probability distribution function results indicate that perturbation causes the fluctuations in vibration scales and smaller scales with high intensity and low intermittency. Based on the flatness factor, the bursting process is also detected. The vibrations reduce the relative intensities of the burst events, indicating that the streamwise vortices in the buffer layer experience direct interference due to the PZT control.

Measurements in an Axisymmetric Turbulent Boundary Layer Along a Circular Cylinder

1976 ◽  
Vol 27 (3) ◽  
pp. 217-228 ◽  
Author(s):  
Noor Afzal ◽  
K P Singh
Keyword(s):  
Boundary Layer ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Constant Pressure ◽  
Reynolds Shear Stress ◽  
Longitudinal Velocity ◽  
Outer Region ◽  
Wall Region ◽  
Mean Velocity ◽  
Dimensional Boundary

SummaryIn an axisymmetric turbulent boundary layer along a circular cylinder at constant pressure, measurements have been made of mean velocity profile and turbulence characteristics: longitudinal velocity fluctuations, Reynolds shear stress, transverse correlation and spectrum. It has been found that the qualitative behaviour of an axisymmetric turbulent boundary layer is similar to that of a two-dimensional boundary layer in the wall region, where as in the outer region the effects of transverse curvature are observed.

Direct numerical simulation of the turbulent boundary layer over a cube-roughened wall

2011 ◽  
Vol 669 ◽  
pp. 397-431 ◽  
Author(s):  
JAE HWA LEE ◽  
HYUNG JIN SUNG ◽  
PER-ÅGE KROGSTAD
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Direct Numerical Simulation ◽  
Outer Layer ◽  
Large Scale ◽  
Roughness Height ◽  
Wall Region ◽  
Momentum Thickness ◽  
Reynolds Stresses

Direct numerical simulation (DNS) of a spatially developing turbulent boundary layer (TBL) over a wall roughened with regularly arrayed cubes was performed to investigate the effects of three-dimensional (3-D) surface elements on the properties of the TBL. The cubes were staggered in the downstream direction and periodically arranged in the streamwise and spanwise directions with pitches of px/k = 8 and pz/k = 2, where px and pz are the streamwise and spanwise spacings of the cubes and k is the roughness height. The Reynolds number based on the momentum thickness was varied in the range Reθ = 300−1300, and the roughness height was k = 1.5θin, where θin is the momentum thickness at the inlet, which corresponds to k/δ = 0.052–0.174 from the inlet to the outlet; δ is the boundary layer thickness. The characteristics of the TBL over the 3-D cube-roughened wall were compared with the results from a DNS of the TBL over a two-dimensional (2-D) rod-roughened wall. The introduction of cube roughness affected the turbulent Reynolds stresses not only in the roughness sublayer but also in the outer layer. The present instantaneous flow field and linear stochastic estimations of the conditional averaging showed that the streaky structures in the near-wall region and the low-momentum regions and hairpin packets in the outer layer are dominant features in the TBLs over the 2-D and 3-D rough walls and that these features are significantly affected by the surface roughness throughout the entire boundary layer. In the outer layer, however, it was shown that the large-scale structures over the 2-D and 3-D roughened walls have similar characteristics, which indicates that the dimensional difference between the surfaces with 2-D and 3-D roughness has a negligible effect on the turbulence statistics and coherent structures of the TBLs.

Convex Turbulent Boundary Layers With Zero and Favorable Pressure Gradients

1996 ◽  
Vol 118 (4) ◽  
pp. 787-794 ◽  
Author(s):  
A. C. Schwarz ◽  
M. W. Plesniak
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Boundary Layers ◽  
Reynolds Stress ◽  
Strain Rates ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
The Mean ◽  
Stress Profiles

A turbulent boundary layer subjected to multiple, additional strain rates, namely convex curvature coupled with streamwise pressure gradients (zero and favorable, ZPG and FPG) was investigated experimentally using laser Doppler velocimetry. The inapplicability of the universal flat-plate log-law to curved flows is discussed. However, a logarithmic region is found in the curved and accelerated turbulent boundary layer examined here. Similarity of the mean velocity and Reynolds stress profiles was achieved by 45 deg of curvature even in the presence of the strongest FPG investigated (k = 1.01 × 10−6). The Reynolds stresses were suppressed (with respect to flat plate values) due primarily to the effects of strong convex curvature (δo/R ≈ 0.10). In curved boundary layers subjected to different favorable pressure gradients, the mean velocity and normal Reynolds stress profiles collapsed in the inner region, but deviated in the outer region (y+ ≥ 100). Thus, inner scaling accounted for the impact of the extra strain rates on these profiles in the near-wall region. Combined with curvature, the FPG reduced the strength of the wake component, resulted in a greater suppression of the fluctuating velocity components and a reduction of the primary Reynolds shear stress throughout almost the entire boundary layer relative to the ZPG curved case.

Measurement Investigation of Complex Eddy Viscosity Model in Non-Equilibrium Wavy Wall Turbulence with TRPIV

2013 ◽  
Vol 718-720 ◽  
pp. 1657-1662
Author(s):  
An Tong Zhang ◽  
Nan Jiang
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Strain Rate ◽  
Reynolds Stress ◽  
Eddy Viscosity ◽  
Wavy Wall ◽  
Streamwise Direction ◽  
Mean Velocity ◽  
Eddy Viscosity Model ◽  
Phase Differences

The spatial flow fields of turbulent boundary layer over a wavy wall were measured by TRPIV at three different Reynolds numbers in a water channel, the mean streamwise and wall-normal velocities near the wall were calculated from the time series of instantaneous spatial 2D-2C flow fields of turbulent boundary layer, and the periodic distributions of the streamwise and wall-normal velocity in streamwise direction influenced by the wavy wall were found. The spatial distributions of Reynolds stress and mean velocity strain rate were obtained by ensemble average. Using the spatial cross-correlation technique, the spatial phase relationship in streamwise direction between mean velocity strain rate and Reynolds stress was investigated. It is found that there exist spatial phase differences between Reynolds stress components and mean velocity strain rate components, the phase differences increase gradually after decrease gradually from zero away from the wavy wall in wall-normal direction and reach a minimum at 0.4~0.5 times the wavelength of wavy wall, and in a certain range the effect of the Reynolds number on the phase differences is very small. The reasonability of the complex eddy viscosity model is confirmed by these experimental evidences in order to forecast non-equilibrium turbulence accurately.

LDA Measurements on Rough Turbulent Boundary Layers Subject to Strong Favorable Pressure Gradients

2006 ◽  
Author(s):  
Rau´l Bayoa´n Cal ◽  
Brian Brzek ◽  
Gunnar Johansson ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Rough Surface ◽  
Reynolds Stress ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Velocity Deficit ◽  
The Mean ◽  
Stress Profiles

Laser-Doppler anemometry (LDA) measurements of the mean velocity and Reynolds stresses are carried out on a rough surface favorable pressure gradient (FPG) turbulent boundary layer. These data is compared with smooth FPG turbulent boundary layer data possessing with the same strength of pressure gradient and also with rough zero pressure gradient (ZPG) data. The scales for the mean velocity deficit and Reynolds stresses are obtained through means of equilibrium similarity analysis of the RANS equations [1]. The mean velocity deficit profiles collapse, but to different curves when normalized using the free-stream velocity. The effects of the pressure gradient and roughness are clearly distinguished and separated. However, these effects are removed from the outer flow when the profiles are normalized using the Zagarola and Smits [2] scaling. It is also found that there is a clear effect of the roughness and pressure gradient on the Reynolds stresses. The Reynolds stress profiles augment due to the rough surface. Furthermore, the strength of the pressure gradient imposed of the flow changes the shape of the Reynolds stress profiles especially on the < v2 > and < uv > components. The rough surface influence is mostly noticed on the < u2 > component of the Reynolds stress, where the shape of the profiles change entirely. The boundary layer parameter δ*/δ shows the effects of the roughness and a dependence on the Reynolds number for the smooth FPG case. The pressure parameter, A, describes a development of the turbulent boundary layer and no influence of the roughness is linked with the parameter, k+. The boundary layers grow differently and depict the influence of the studied effects in their development. These measurements are the first of their nature due to the extensive number in downstream locations (12) and the combination of the studied external conditions (i.e., the strength of the pressure gradient and the surface roughness).

LDA-Measurements of Transitional Flows Induced by a Square Rib

2001 ◽  
Vol 124 (1) ◽  
pp. 108-117 ◽  
Author(s):  
S. Becker ◽  
C. M. Stoots ◽  
K. G. Condie ◽  
F. Durst ◽  
D. M. McEligot
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Laser Doppler Anemometry ◽  
Plate Boundary ◽  
Index Of Refraction ◽  
Wall Region ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Turbulent Statistics

New fundamental measurements are presented for the transition process in flat plate boundary layers downstream of two-dimensional square ribs. By use of laser Doppler anemometry (LDA) and a large Matched-Index-of-Refraction (MIR) flow system, data for wall-normal fluctuations and Reynolds stresses were obtained in the near wall region to y+<0.1 in addition to the usual mean streamwise velocity component and its fluctuation. By varying velocity and rib height, the experiment investigated the following range of conditions: k+=5.5 to 21, 0.3<k/δ1<1,180<Rek<740,6×104<Rex,k<1.5×105,ReΘ660,−125<x−xk/k<580. Consequently, results covered boundary layers which retained their laminar characteristics through those where a turbulent boundary layer was established shortly after reattachment beyond the forcing rib. For “large” elements, evolution of turbulent statistics of the viscous layer for a turbulent boundary layer y+<∼30 was rapid even in flows where the mean velocity profile still showed laminar behavior.

Simultaneous flow visualization and Reynolds-stress measurement in a turbulent boundary layer

1986 ◽  
Vol 163 ◽  
pp. 459-478 ◽  
Author(s):  
A. M. Talmon ◽  
J. M. G. Kunen ◽  
G. Ooms
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flow Visualization ◽  
Reynolds Stress ◽  
Stress Measurement ◽  
Three Dimensional ◽  
Time Dependent ◽  
Flow Structures ◽  
Wall Region ◽  
Measured Velocity

Flow visualization and Reynolds-stress measurement were combined in an investigation of a turbulent boundary layer in a water channel. Hydrogen bubbles were used to visualize the flow; a laser-Doppler anemometer capable of measuring two velocity components was applied to measure the instantaneous value of the Reynolds stress. Owing to the three-dimensional, time-dependent character of the flow it was rather difficult to identify flow structures from measured velocity signals, especially at larger distances from the wall. Despite this difficulty a method based on the instantaneous value of the Reynolds stress could be developed for detecting bursts in the wall region of the boundary layer. By this method the three-dimensional, time-dependent character of the flow is taken into account by attributing to the same burst ejections occurring successively with very short time intervals. This identification procedure is based on a comparison on a one-to-one basis between visualized flow structures and measured values of the Reynolds stress. The detected bursts were found to make a considerable contribution to the momentum transport in the boundary layer.

Experiment on Turbulent Boundary Layers on a Concave Wall

1975 ◽  
Vol 26 (1) ◽  
pp. 25-40 ◽  
Author(s):  
Ronald M C So ◽  
George L Mellor
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Present Experiment ◽  
Large Scale ◽  
Turbulent Boundary Layers ◽  
Turbulence Level ◽  
Mean Velocity ◽  
Concave Wall ◽  
Transverse Profile

SummaryThe present experiment describes the behaviour of a turbulent boundary layer on a concave wall. At the onset of curvature there appears a fairly coherent wavelike transverse profile of mean velocity. This disturbance might be interpreted as a kind of large scale Taylor-Görtler type instability superimposed on a conventional turbulent boundary layer; further downstream the coherence degenerates as the turbulence level increases. Boundary-layer profile measurements were made at positions of maxima and minima of transverse profiles of (U-component) mean velocity. The boundary layer at the minima positions is found to be twice as thick as that at the maxima positions. Also, turbulent intensities inside the boundary layer are substantially increased as a result of the concave curvature of the surface.

Sign in / Sign up

Export Citation Format

Share Document