Numerical Simulation of Temperature Distribution in Multi-Phase Materials as a Result of Selective Heating by Microwave Energy

2008 ◽  
Vol 43 (1) ◽  
pp. 27-33 ◽  
Author(s):  
Noboru Yoshikawa ◽  
Yoshio Tokuyama
Author(s):  
Junnosuke Okajima ◽  
Atsuki Komiya ◽  
Shigenao Maruyama

The objective of this work is to experimentally and numerically evaluate small-scale cryosurgery using an ultrafine cryoprobe. The outer diameter (OD) of the cryoprobe was 550 μm. The cooling performance of the cryoprobe was tested with a freezing experiment using hydrogel at 37 °C. As a result of 1 min of cooling, the surface temperature of the cryoprobe reached −35 °C and the radius of the frozen region was 2 mm. To evaluate the temperature distribution, a numerical simulation was conducted. The temperature distribution in the frozen region and the heat transfer coefficient was discussed.


2014 ◽  
Vol 6 (2) ◽  
pp. 77-85
Author(s):  
Pratibha Joshi ◽  
Manoj Kumar

Many studies have been done previously on temperature distribution in inhomogeneous composite systems with perfect interface, having no discontinuities along it. In this paper we have determined steady state temperature distribution in two inhomogeneous composite systems with imperfect interface, having discontinuities in temperature and heat flux using decomposed immersed interface method and performed the numerical simulation on MATLAB.


2021 ◽  
Author(s):  
Song Du ◽  
Seong Lee ◽  
Xian-Huan Wen ◽  
Yalchin Efendiev

Abstract The imbibition process due to capillary force is an important mechanism that controls fluid flow between the two domains, matrix and fracture, in naturally or hydraulically fractured reservoirs. Many simulation studies have been done in the past decades to understand the multi-phase flow in the tight and shale formation. Although significant advances have been made in large-scale modeling for both unconventional and conventional fields, the imbibition processes in the fractured reservoirs remains underestimated in numerical simulation, that limits confidence in long-term field production predictions. In the meanwhile, to simulate the near-fracture imbibition process, traditionally very-fine simulation grids have to be applied so that the physical phenomena of small-length scale could be captured. However, this leads to expensive computation cost to simulate full-field models with a large number of fractures. To improve numerical efficiency in field-scale modeling, we propose a similarity solution for the imbibition process that can be incorporated into the traditional finite difference formulation with coarse grid cells. The semi-analytical similarity solutions are validated by comparing with numerical simulation results with fine-scale grids. The comparison clearly indicates that the proposed algorithm accurately represents the flow behaviors in complex fracture models. Furthermore, we adopt the semi-analytical study to hydraulic fracture models using Embedded Discrete Fracture Model (Lee et al., 2001) in our numerical studies at different scales to represent hydraulic fractures that are interconnected. We demonstrate: 1) the imbibition is critical in determining flow behavior in a capillary force dominant model, 2) conventional EDFM has its limitation in capturing sub-cell flow behaviors near fractures, 3) combining the proposed similarity solution and EDFM, we can accurately represent the multi-phase flow near fractures with coarser grids, and 4) it is straightforward to adapt the similarity solution concept in finite-difference simulations for fractured reservoirs


Author(s):  
Yoichi Utanohara ◽  
Michio Murase ◽  
Akihiro Masui ◽  
Ryo Inomata ◽  
Yuji Kamiya

The structural integrity of the containment vessel (CV) for a pressurized water reactor (PWR) plant under a loss-of-coolant accident is evaluated by a safety analysis code that uses the average temperature of gas phase in the CV during reactor operation as an initial condition. Since the estimation of the average temperature by measurement is difficult, this paper addressed the numerical simulation for the temperature distribution in the CV of an operating PWR plant. The simulation considered heat generation of the equipment, the ventilation and air conditioning systems (VAC), heat transfer to the structure, and heat release to the CV exterior based on the design values of the PWR plant. The temperature increased with a rise in height within the CV and the flow field transformed from forced convection to natural convection. Compared with the measured temperature data in the actual PWR plant, predicted temperatures in the lower regions agreed well with the measured values. The temperature differences became larger above the fourth floor, and the temperature inside the steam generator (SG) loop chamber on the fourth floor was most strongly underestimated, −16.2  K due to the large temperature gradient around the heat release equipment. Nevertheless, the predicted temperature distribution represented a qualitative tendency, low at the bottom of the CV and increases with a rise in height within the CV. The total volume-averaged temperature was nearly equal to the average gas phase temperature. To improve the predictive performance, parameter studies regarding heat from the equipment and the reconsideration of the numerical model that can be applicable to large temperature gradient around the equipment are needed.


Sign in / Sign up

Export Citation Format

Share Document