Modeling of integrated solar combined cycle power plant (ISCC) of Hassi R'mel, Algeria

2019 ◽  
Vol 14 (3) ◽  
pp. 505-526 ◽  
Author(s):  
Nedjma Abdelhafidi ◽  
Nour El Islam Bachari ◽  
Zohra Abdelhafidi ◽  
Ali Cheknane ◽  
Abdelmotaleb Mokhnache ◽  
...  
Keyword(s):  
Power Plant ◽  
Solar Energy ◽  
Power Plants ◽  
Meteorological Data ◽  
Combined Cycle ◽  
Plant Responses ◽  
Content Type ◽  
Low Wind Speed ◽  
Gas Power Plant ◽  
Solar Electricity

Purpose Integrated solar combined cycle (ISCC) using parabolic trough collector (PTC) technology is a new power plant that has been installed in few countries to benefit from the use of hybrid solar-gas systems. The purpose of this paper is to investigate the challenges in modeling the thermal output of the hybrid solar-gas power plant and to analyze the factors that influence them. Design/methodology/approach To validate the proposal, a study was conducted on a test stand in situ and based on the statistical analysis of meteorological data of the year 2017. Such data have been brought from Abener hybrid solar-gas central of Hassi R’mel and used as an input of our model. Findings The proposal made by the authors has been simulated using MATLAB environment. The simulation results show that the net solar electricity reaches 18 per cent in June, 15 per cent in March and September, while it cannot exceed 8 per cent in December. Moreover, it shows that the power plant responses sensibly to solar energy, where the electricity output increases accordingly to the solar radiation increase. This increase in efficiency results in better economic utilization of the solar PTC equipment in such kind of hybrid solar-gas power plant. Practical implications The obtained results would be expected to provide the possibility for designing other power plants in Algeria when such conditions are met (high DNI, low wind speed, water and natural-gas availability). Originality/value This paper presents a new model able to predict the thermal solar energy and the net solar-electricity efficiency of such kind solar hybrid power plant.

Thermoeconomic Evaluation of Solar Thermal and Photovoltaic Hybridization Options for Combined-Cycle Power Plants

2014 ◽  
Author(s):  
James Spelling ◽  
Björn Laumert
Keyword(s):  
Power Plant ◽  
Solar Energy ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
First Generation ◽  
Combined Cycle ◽  
Solar Thermal ◽  
Hybrid Power ◽  
Cycle Systems ◽  
Solar Electricity

The hybridization of combined-cycle power plants with solar energy is an attractive means of reducing carbon dioxide emissions from gas-based power generation. However, the construction of the first generation of commercial hybrid power plants will present the designer with a large number of choices. To assist decision making, a thermoeconomic study has been performed for three different hybrid power plant configurations, including both solar thermal and photovoltaic hybridization options. Solar photovoltaic combined-cycle power plants were shown to be able to integrate up to 63 % solar energy on an annual basis, whereas hybrid gas-turbine combined-cycle systems provide the lowest cost of solar electricity, with costs only 2.1 % higher than a reference, unmodified combined-cycle power plant. The integrated solar combined-cycle configuration has been shown to be economically unattractive.

Thermo-Economic Evaluation of Solar Thermal and Photovoltaic Hybridization Options for Combined-Cycle Power Plants

2014 ◽  
Vol 137 (3) ◽  
Author(s):  
James Spelling ◽  
Björn Laumert
Keyword(s):  
Power Plant ◽  
Solar Energy ◽  
Power Plants ◽  
First Generation ◽  
Combined Cycle ◽  
Solar Thermal ◽  
Hybrid Power ◽  
Hybrid Power Plant ◽  
Carbon Dioxide Co2 ◽  
Solar Electricity

The hybridization of combined-cycle power plants with solar energy is an attractive means of reducing carbon dioxide (CO2) emissions from gas-based power generation. However, the construction of the first generation of commercial hybrid power plants will present the designer with a large number of choices. To assist decision making, a thermo-economic study has been performed for three different hybrid power plant configurations, including both solar thermal and photovoltaic hybridization options. Solar photovoltaic combined-cycle (SPVCC) power plants were shown to be able to integrate up to 63% solar energy on an annual basis, whereas hybrid gas turbine combined-cycle (HGTCC) systems provide the lowest cost of solar electricity, with costs only 2.1% higher than a reference, unmodified combined-cycle power plant. The integrated solar combined-cycle (ISCC) configuration has been shown to be economically unattractive.

scholarly journals Assessment on Energy Conversion Efficiency and GHG Emissions Rate for Coal, Natural Gas and Biomass Power Plant in Malaysia

2021 ◽  
Vol 87 (2) ◽  
pp. 145-153
Author(s):  
Radin Diana R. Ahmad ◽  
Tiong Sieh Kiong ◽  
Sazalina Zakaria ◽  
Ahmad Rosly Abbas ◽  
Chen Chai Phing ◽  
...  
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Energy Conversion ◽  
Conversion Efficiency ◽  
Power Plants ◽  
Emission Rate ◽  
Energy Conversion Efficiency ◽  
Combined Cycle ◽  
Gas Power Plant ◽  
Biomass Power Plant

Three different power plants have been assessed in terms of energy conversion efficiency and GHGs emission rate. The power plants are coal power plant, natural gas power plant and biomass power plant. The assessments are made by collecting fuels consumption data and generated electricity data of each power plant. In addition to the data collection, observation on operational practices have also been carried out. The energy conversion efficiency and the GHGs emission rate for all power plants are recorded to be lower than the typical values proposed by the literature. The biomass power plant recorded the lowest energy conversion efficiency at 6.47 %. Meanwhile, the natural gas power plant utilizing the combined cycle gas turbine technology recorded the highest overall energy conversion efficiency at 48.35 % and rated to emit GHGs at 0.32 kg CO2e per kWh.

scholarly journals Inclusion of solar energy in iraq gas-turbine power plants as a method of solving the country's energy system shortage

2020 ◽  
Vol 22 (2) ◽  
pp. 98-107 ◽  
Author(s):  
A. Z. Abass ◽  
D. A. Pavlyuchenko ◽  
A. M. Balabanov ◽  
V. M. Less
Keyword(s):  
Power Plant ◽  
Solar Energy ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Energy System ◽  
Combustion Products ◽  
Combined Cycle ◽  
Solar Collectors ◽  
Technical Solutions

At high ambient temperatures, the performance of gas turbine power plants drops significantly. Technical solutions of compensation for losses associated with the constant injection of water into the air intake of a gas turbine. This approach is not acceptable in regions with limited fresh water reserves. Radical solutions are required to reduce the cost of generated energy. Integrated Combined Solar Cycle (ISCCS) technology has proven itself on many projects. The addition of a combined cycle gas cycle with solar energy can significantly increase the overall efficiency of the power plant. Despite the increase in costs during the construction of its solar part, the total cost of operating solar collectors is several times less than a turbine installation. Given the global trend to fight carbon emissions, switching to a hybrid scheme is economically attractive. Trading in carbon credits for CO2 emissions will significantly reduce the payback period for the construction of gas turbine modernization under the ISCCS scheme. This paper presents an option to modernize a gas turbine power plant in the city of Basra (Iraq), using the advantages of solar radiation and recycling of combustion products from gas turbines. It is proposed to equip the existing 200 MW gas turbine plant with two steam turbine units with a capacity of 75 and 65 MW, working in conjunction with solar collectors producing low pressure water vapor. Due to modernization, the efficiency of the power plant should increase from 38% to 55%. The revision of the schematic and technical solutions of Iraq power plants will allow producing sufficient energy for the region.

Automating attendance recording of contingent labours at a large construction site

2012 ◽  
Vol 2 (8) ◽  
pp. 1-9
Author(s):  
Saroj Koul
Keyword(s):  
Power Plant ◽  
Radio Frequency Identification ◽  
Power Plants ◽  
Subject Area ◽  
Management Control ◽  
Class Discussion ◽  
Construction Site ◽  
Large Power ◽  
Content Type

Subject area Operations and human resourcing. Study level/applicability This case study is intended for use in graduate, executive level management and doctoral programs. The case study illustrates a combined IT and HR driven participative management control system in a flexible organization structure. It is intended for a class discussion rather than to illustrate either effective or ineffective handling of an administrative situation. Case overview The case describes the situation of managing unskilled workforces (≥14,000 workers) during the construction phase of the 4 × 250MW power plants both for purposes of turnout as well as due compensation, in the event of an accident. The approved labour forces appointed for 45 × 8 h. Man-days after a rigorous fitness test and approvals of the safety officer are allocated housing and other necessary amenities and a commensurate compensation system. Expected learning outcomes These include: illustrating typical organizational responsibility structure at a construction site of a large power plant; illustrating the planning and administrative control mechanism in implementing strategy at a construction site of a large power plant; offering students the opportunity to understand and view a typical operational (project) structure; allowing students to speculate adaptations in the wake of an ever-changing business and company environment; and providing an opportunity to introduce a power scenario in India, Indian labour laws and radio frequency identification technology and to relate this to the case in context. Supplementary materials Teaching notes are available; please consult your librarian for access.

Output Power Correlation Between Nearby Wind Power Plants

2003 ◽  
Author(s):  
Yih-Huei Wan ◽  
Michael Milligan ◽  
Brian Parsons
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Power Output ◽  
High Frequency ◽  
Power Plants ◽  
Meteorological Data ◽  
Low Frequency ◽  
Spatial Separation ◽  
Wind Power Plant ◽  
Wind Power Plants

The National Renewable Energy Laboratory (NREL) started a project in 2000 to record long-term, high-frequency (1-Hz) wind power output data from large commercial wind power plants. Outputs from about 330 MW of wind generating capacity from wind power plants in Buffalo Ridge, Minnesota, and Storm Lake, Iowa, are being recorded. Analysis of the collected data shows that although very short-term wind power fluctuations are stochastic, the persistent nature of wind and the large number of turbines in a wind power plant tend to limit the magnitudes and rates of changes in the levels of wind power. Analyses of power data confirm that spatial separation greatly reduces variations in the combined wind power output relative to output from a single wind power plant. Data show that high frequency variations of wind power from two wind power plants 200 km apart are independent of each other, but low frequency power changes can be highly correlated. This fact suggests that time-synchronized power data and meteorological data can aid in the development of statistical models for wind power forecasting.

scholarly journals A countrywide analysis of 27 solar power plants installed at different climates

2022 ◽  
Vol 12 (1) ◽  
Author(s):  
Talat Ozden
Keyword(s):  
Power Plant ◽  
Alternative Energy ◽  
Power Plants ◽  
Solar Power ◽  
Meteorological Data ◽  
Energy Sources ◽  
Climate Classification ◽  
Climate Type ◽  
Monthly Average ◽  
The World

AbstractThe world is still heavily using nonconventional energy sources, which are worryingly based on carbon. The step is now alternative energy sources hoping that they will be more environmentally friendly. One of the important energy conversion forms by using these sources is photovoltaic solar systems. These type of power plants is on the increase in everyday on the world. Before investment a solar power plant in a specified region, a techno-economic analyse is performed for that power plant by using several meteorological data like solar irradiance and ambient temperature. However, this analyses generally lacks evaluation on effects of climatic and geographical conditions. In this work, 5 years of data of 27 grid-connected photovoltaic power plants are investigated, which are installed on seven different climate types in Turkey. Firstly, the power plants are categorized considering the tilt angles and Köppen–Gieger climate classification. The performance evaluations of the plants are mainly conducted using monthly average efficiencies and specific yields. The monthly average efficiencies, which were classified using the tilts and climate types were from 12 to 17%, from 12 to 16% and from 13 to 15% for tilts 30°/10°, 25° and 20°, respectively. The variation in the specific yields decrease with elevation as y(x) =  − 0.068x + 1707.29 (kWh/kWp). As the performances of photovoltaic systems for some locations within the Csb climatic regions may relatively lower than some other regions with same climate type. Thus, techno-economic performance for PVPP located in this climate classification should be carefully treated.

scholarly journals Improving the Efficiency of Solar Power Plants

2020 ◽  
Vol 30 (3) ◽  
pp. 480-497
Author(s):  
Dmitriy S. Strebkov ◽  
Yuriy Kh. Shogenov ◽  
Nikolay Yu. Bobovnikov
Keyword(s):  
Power Plant ◽  
Solar Radiation ◽  
Solar Energy ◽  
Power Plants ◽  
Solar Power ◽  
Horizontal Surface ◽  
Solar Power Plant ◽  
Utilization Factor ◽  
Working Surface ◽  
Solar Power Plants

Introduction. An urgent scientific problem is to increase the efficiency of using solar energy in solar power plants (SES). The purpose of the article is to study methods for increasing the efficiency of solar power plants. Materials and Methods. Solar power plants based on modules with a two-sided working surface are considered. Most modern solar power plants use solar modules. The reflection of solar radiation from the earth’s surface provides an increase in the production of electrical energy by 20% compared with modules with a working surface on one side. It is possible to increase the efficiency of using solar energy by increasing the annual production of electric energy through the creation of equal conditions for the use of solar energy by the front and back surfaces of bilateral solar modules. Results. The article presents a solar power plant on a horizontal surface with a vertical arrangement of bilateral solar modules, a solar power station with a deviation of bilateral solar modules from a vertical position, and a solar power plant on the southern slope of the hill with an angle β of the slope to the horizon. The formulas for calculating the sizes of the solar energy reflectors in the meridian direction, the width of the solar energy reflectors, and the angle of inclination of the solar modules to the horizontal surface are given. The results of computer simulation of the parameters of a solar power plant operating in the vicinity of Luxor (Egypt) are presented. Discussion and Conclusion. It is shown that the power generation within the power range of 1 kW takes a peak value for vertically oriented two-sided solar modules with horizontal reflectors of sunlight at the installed capacity utilization factor of 0.45. At the same time, when the solar radiation becomes parallel to the plane of vertical solar modules, there is a decrease in the output of electricity. The proposed design allows equalizing and increasing the output of electricity during the maximum period of solar radiation. Vertically oriented modules are reliable and easy to use while saving space between modules.

“Building as machine”: mental image of combined cycle power plants workers

Facilities ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mohammad Rezaee ◽  
Seyed Rahman Eghbali
Keyword(s):  
Data Collection ◽  
Power Plants ◽  
Thermal Power ◽  
Mental Image ◽  
Careful Analysis ◽  
Combined Cycle ◽  
Collection Method ◽  
Content Type ◽  
Environmental Threats ◽  
Data Collection Method

Purpose This paper aims to interpret the workers’ perception of combined cycle power plants through visual qualities. Design/methodology/approach In this qualitative research landscape image, the sketching technique is applied as a data collection method to extract participants’ mental images by asking them to draw sketches. The resulted sketches besides obtained verbal and written data were analyzed and coded in three stages to explain the workers’ perception. Visual qualities were studied as a mean which made it possible to interpret the workers’ perception of their workplace. Findings Careful analysis of the gathered data and the emerged concepts via open coding identify four axial categories of the concepts forming the workers’ perception of the power plants: “inconsistency with nature,” “emphasis on function and product,” “health and environmental threats” and “interpretation of the built form as a mass instead of space.” These four categories support the core category of the proposed theory which is “perceiving building as the machine.” This phrase explains how workers perceive power plants as machines, not as supportive and lively environments. This is followed by consequences, “precedence of building over human” is prominent among them. Originality/value In the relevant body of literature, visual impact and visual perception of conventional thermal power plants are largely missed, as well as visual relation to environment focusing on a single building or groups of adjacent buildings. This paper covers both areas via asking for sketches as a data collection method, in addition, to interview the participants to clarify their mental image of the work environment.

Thermo-Economic Assessment Under Electrical Market Uncertainties of a Combined Cycle Gas Turbine Integrated With a Flue Gas-Condensing Heat Pump

2020 ◽  
Author(s):  
Alberto Vannoni ◽  
Andrea Giugno ◽  
Alessandro Sorce
Keyword(s):  
Power Plant ◽  
Power Systems ◽  
Gas Turbine ◽  
Heat Pump ◽  
Flue Gas ◽  
Power Plants ◽  
Greenhouse Gas Emission ◽  
Capital Expenditure ◽  
Combined Cycle ◽  
Gas Turbine Power Plant

Abstract Renewable energy penetration is growing, due to the target of greenhouse-gas-emission reduction, even though fossil fuel-based technologies are still necessary in the current energy market scenario to provide reliable back-up power to stabilize the grid. Nevertheless, currently, an investment in such a kind of power plant might not be profitable enough, since some energy policies have led to a general decrease of both the average price of electricity and its variability; moreover, in several countries negative prices are reached on some sunny or windy days. Within this context, Combined Heat and Power systems appear not just as a fuel-efficient way to fulfill local thermal demand, but also as a sustainable way to maintain installed capacity able to support electricity grid reliability. Innovative solutions to increase both the efficiency and flexibility of those power plants, as well as careful evaluations of the economic context, are essential to ensure the sustainability of the economic investment in a fast-paced changing energy field. This study aims to evaluate the economic viability and environmental impact of an integrated solution of a cogenerative combined cycle gas turbine power plant with a flue gas condensing heat pump. Considering capital expenditure, heat demand, electricity price and its fluctuations during the whole system life, the sustainability of the investment is evaluated taking into account the uncertainties of economic scenarios and benchmarked against the integration of a cogenerative combined cycle gas turbine power plant with a Heat-Only Boiler.

Sign in / Sign up

Export Citation Format

Share Document