Neural Modeling of the Surface Acoustic Wave Resonator Admittance Parameters

2021 ◽  
Author(s):  
Zlatica Marinkovic ◽  
Giovanni Gugliandolo ◽  
Antonino Quattrocchi ◽  
Giovanni Crupi ◽  
Nicola Donato
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Neural Modeling ◽  
Wave Resonator

Surface acoustic wave resonator from thick MOVPE-grown layers of GaN(0001) on sapphire

2002 ◽  
Vol 743 ◽  
Author(s):  
Sverre V. Pettersen ◽  
Thomas Tybell ◽  
Arne Rønnekleiv ◽  
Stig Rooth ◽  
Veit Schwegler ◽  
...  
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Electromechanical Coupling ◽  
Film Surface ◽  
Center Frequency ◽  
Electromechanical Coupling Coefficient ◽  
Nitride Film ◽  
Wave Resonator ◽  
Lift Off ◽  
Definition Of

ABSTRACTWe report on fabrication and measurement of a surface acoustic wave resonator prepared on ∼10m thick GaN(0001) films. The films were grown by metal-organic vapor phase epitaxy on a c-plane sapphire substrate. The surface morphology of the films were examined with scanning electron and atomic force microscopy. A metallic bilayer of Al/Ti was subsequently evaporated on the nitride film surface. Definition of the resonator interdigital transducers, designed for a wavelength of λ=7.76m, was accomplished with standard UV lithography and lift-off. S-parameter measurements showed a resonator center frequency f0=495MHz at room temperature, corresponding to a surface acoustic wave velocity of 3844m/s. The insertion loss at center frequency was measured at 8.2dB, and the loaded Q-factor was estimated at 2200. Finally, measurements of the resonator center frequency for temperatures in the range 25–155°C showed a temperature coefficient of -18ppm/°C. The intrinsic GaN SAW velocity and electromechanical coupling coefficient were estimated at νSAW=383 1m/s and K2=1.8±0.4·10−3.

Computational Fluid Dynamics Simulation, Microelectromechanical System Fabrication, and Radio-Frequency Evaluation of the PM2.5 Fine Dust Sensor Based on the Surface Acoustic Wave Resonator

2021 ◽  
Vol 16 (5) ◽  
pp. 715-722
Author(s):  
Se-Yong Park ◽  
Min-Ji Kim ◽  
Hee-Chul Lee
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Surface Cleaning ◽  
Dynamics Simulation ◽  
Fine Dust ◽  
Computational Fluid Dynamics Simulation ◽  
Microelectromechanical System ◽  
Wave Resonator

To classify 2.5-µm-scale fine dust and measure its concentration, research was conducted to produce a fine-dust sensor utilizing computational fluid dynamics simulation and microelectromechanical system processes, and the measurement system was manufactured for the sensor. The virtual impactor was designed to classify particles in the air above and below 2.5 µm, and the cut-off diameter of 2.5 µm at an acceleration nozzle length of 83.2 µm was obtained by verifying this impactor through flow-analysis simulation. The microheater was then designed to measure the mass of the classified particle by adsorbing it onto the surface acoustic wave resonator placed on the lower part of the flow channel using thermophoretic force. The conditions where the classified particles are completely adsorbed on the surface acoustic wave resonator through the heater were calculated using numerical modeling and the results were verified through the simulation. The fine dust sensor based on the designed surface acoustic wave resonator is composed of the upper, middle, and lower parts including the heater, virtual impactor, and surface acoustic wave resonator and SMA connector, respectively, and the micro-fan controlling the total flow. Each part was produced using the microelectromechanical system process, assembled, and finally finished. Moreover, the evaluation system was produced in this study to assess the developed sensor. The flow of air controlled through the flowmeter was sprayed into a dust bottle filled with hollow silica powder to scatter the powder, which flowed into the system with the air, making the environment similar to one with fine dust present. The change in radio-frequency resonance characteristics, such as those before and after exposure to the fine dust environment, and insertion loss after the surface cleaning were observed, and a sensitivity of, detection limit of, and restoration rate after surface cleaning exceeding 99.9% were obtained.

Multilayer graphene electrodes for one-port surface acoustic wave resonator mass sensor

2017 ◽  
Vol 56 (2) ◽  
pp. 024301 ◽  
Author(s):  
Ainan Leong ◽  
Varghese Swamy ◽  
N. Ramakrishnan
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Multilayer Graphene ◽  
Mass Sensor ◽  
Wave Resonator

Monolithic surface acoustic wave resonator oscillator

1983 ◽  
Vol 54 (3) ◽  
pp. 1268-1272 ◽  
Author(s):  
T. A. Raju ◽  
N. G. Kurahatti ◽  
N. M. Dube ◽  
M. K. Roy
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Wave Resonator

Effects of Delay Lines on Surface Acoustic Wave Resonator Filters and Their Applications

1998 ◽  
Vol 37 (Part 1, No. 11) ◽  
pp. 6029-6033 ◽  
Author(s):  
Sheng-Yuan Chu ◽  
Walter Water
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Delay Lines ◽  
Wave Resonator ◽  
Resonator Filters
Sign in / Sign up

Export Citation Format

Share Document