Drug load and memory during intracarotid amobarbital procedure in epilepsy

Author(s):  
Alejandro Lozano‐García ◽  
Kevin G. Hampel ◽  
Mercedes Garcés‐Sánchez ◽  
Fernando Aparici‐Robles ◽  
Pilar Rubio‐Sánchez ◽  
...  
2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Lu Wang ◽  
Shuwei Liu ◽  
Chunxia Ren ◽  
Siyuan Xiang ◽  
Daowei Li ◽  
...  

AbstractNanomaterial-based drug sustainable release systems have been tentatively applied to bone regeneration. They, however, still face disadvantages of high toxicity, low biocompatibility, and low drug-load capacity. In view of the low toxicity and high biocompatibility of polymer nanomaterials and the excellent load capacity of hollow nanomaterials with high specific surface area, we evaluated the hollow polydopamine nanoparticles (HPDA NPs), in order to find an optimal system to effectively deliver the osteogenic drugs to improve treatment of bone defect. Data demonstrated that the HPDA NPs synthesized herein could efficiently load four types of osteogenic drugs and the drugs can effectively release from the HPDA NPs for a relatively longer time in vitro and in vivo with low toxicity and high biocompatibility. Results of qRT-PCR, ALP, and alizarin red S staining showed that drugs released from the HPDA NPs could promote osteogenic differentiation and proliferation of rat bone marrow mesenchymal stem cells (rBMSCs) in vitro. Image data from micro-CT and H&E staining showed that all four osteogenic drugs released from the HPDA NPs effectively promoted bone regeneration in the defect of tooth extraction fossa in vivo, especially tacrolimus. These results suggest that the HPDA NPs, the biodegradable hollow polymer nanoparticles with high drug load rate and sustainable release ability, have good prospect to treat the bone defect in future clinical practice.


2021 ◽  
Vol 122 ◽  
pp. 108191
Author(s):  
Rosemary Monaghan ◽  
Máire O'Dwyer ◽  
Retha Luus ◽  
Niamh Mulryan ◽  
Philip McCallion ◽  
...  

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4492
Author(s):  
Eric Ofosu Kissi ◽  
Robin Nilsson ◽  
Liebert Parreiras Nogueira ◽  
Anette Larsson ◽  
Ingunn Tho

Fused deposition modelling-based 3D printing of pharmaceutical products is facing challenges like brittleness and printability of the drug-loaded hot-melt extruded filament feedstock and stabilization of the solid-state form of the drug in the final product. The aim of this study was to investigate the influence of the drug load on printability and physical stability. The poor glass former naproxen (NAP) was hot-melt extruded with Kollidon® VA 64 at 10–30% w/w drug load. The extrudates (filaments) were characterised using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). It was confirmed that an amorphous solid dispersion was formed. A temperature profile was developed based on the results from TGA, DSC, and DMA and temperatures used for 3D printing were selected from the profile. The 3D-printed tablets were characterised using DSC, X-ray computer microtomography (XµCT), and X-ray powder diffraction (XRPD). From the DSC and XRPD analysis, it was found that the drug in the 3D-printed tablets (20 and 30% NAP) was amorphous and remained amorphous after 23 weeks of storage (room temperature (RT), 37% relative humidity (RH)). This shows that adjusting the drug ratio can modulate the brittleness and improve printability without compromising the physical stability of the amorphous solid dispersion.


2011 ◽  
Vol 20 (2) ◽  
pp. 209-213 ◽  
Author(s):  
Ashwini Sharan ◽  
Yinn Cher Ooi ◽  
John Langfitt ◽  
Michael R. Sperling

2015 ◽  
Vol 18 (1) ◽  
pp. 180-186 ◽  
Author(s):  
Maria Høtoft Michaelsen ◽  
Kishor M. Wasan ◽  
Olena Sivak ◽  
Anette Müllertz ◽  
Thomas Rades

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Marius Monschke ◽  
Kevin Kayser ◽  
Karl G. Wagner

AbstractAmong the great number of poorly soluble drugs in pharmaceutical development, most of them are weak bases. Typically, they readily dissolve in an acidic environment but are prone to precipitation at elevated pH. This was aimed to be counteracted by the preparation of amorphous solid dispersions (ASDs) using the pH-dependent soluble polymers methacrylic acid ethylacrylate copolymer (Eudragit L100–55) and hydroxypropylmethylcellulose acetate succinate (HPMCAS) via hot-melt extrusion. The hot-melt extruded ASDs were of amorphous nature and single phased with the presence of specific interactions between drug and polymer as revealed by X-ray powder diffraction (XRPD), differential scanning calorimetry (DSC), and Fourier-transform infrared spectroscopy (FT-IR). The ASDs were milled and classified into six particle size fractions. We investigated the influence of particle size, drug load, and polymer type on the dissolution performance. The best dissolution performance was achieved for the ASD made from Eudragit L100–55 at a drug load of 10%, whereby the dissolution rate was inversely proportional to the particle size. Within a pH-shift dissolution experiment (from pH 1 to pH 6.8), amorphous-amorphous phase separation occurred as a result of exposure to acidic medium which caused markedly reduced dissolution rates at subsequent higher pH values. Phase separation could be prevented by using enteric capsules (Vcaps Enteric®), which provided optimal dissolution profiles for the Eudragit L100–55 ASD at a drug load of 10%.


2019 ◽  
Vol 20 (8) ◽  
Author(s):  
Moshe Honick ◽  
Kanika Sarpal ◽  
Alaadin Alayoubi ◽  
Ahmed Zidan ◽  
Stephen W. Hoag ◽  
...  

Addiction ◽  
2009 ◽  
Vol 104 (11) ◽  
pp. 1874-1880 ◽  
Author(s):  
Caleb J. Banta-Green ◽  
Jennifer A. Field ◽  
Aurea C. Chiaia ◽  
Daniel L. Sudakin ◽  
Laura Power ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document