Three-Dimensional Dry/Wet Contact Analysis of Multilayered Elastic/Plastic Solids With Rough Surfaces

2005 ◽  
Vol 128 (1) ◽  
pp. 18-31 ◽  
Author(s):  
Shaobiao Cai ◽  
Bharat Bhushan
Keyword(s):  
Contact Area ◽  
Microelectromechanical Systems ◽  
Rough Surfaces ◽  
Three Dimensional ◽  
Multilayered Structure ◽  
Contact Analysis ◽  
Maximum Displacement ◽  
Elastic Plastic ◽  
Surface Displacements ◽  
Dry And Wet Conditions

Friction/stiction and wear are among the main issues in microelectromechanical systems (MEMS/NEMS) devices having contact interfaces. Relevant parameters, i.e., layers thickness, need to be optimized. The contact analyses of multilayered structure under both dry and wet conditions are necessary to optimize these parameters. This study presents a first attempt to perform three-dimensional contact analysis of multilayered solids with rough surfaces in both dry and wet conditions. The surface displacements and contact pressure distributions are obtained based on variational principle with fast Fourier transform scheme. The effective hardness is modeled and plays a role when the local displacement meets the maximum displacement criterion. Simulations are performed to obtain the contact pressures, fractional total contact area, fractional plastic contact area, surface/subsurface stresses. Relative meniscus forces are obtained with the presence of an ultrathin liquid film for different loads and layers properties. These contact statistics and meniscus forces are analyzed to study the effects of layer-to-substrate ratios of stiffness and hardness, and the layers thickness of rough, two-layered elastic/plastic solids. The methods to decrease friction/stiction and wear are investigated, and the optimum layer parameters are identified.

Contact Analysis of Multilayered Elastic/Plastic Solids With Rough Surfaces for Decreasing Friction and Wear

2005 ◽  
Author(s):  
Shaobiao Cai ◽  
Bharat Bhushan
Keyword(s):  
Surface Roughness ◽  
Contact Area ◽  
Yield Criterion ◽  
Rough Surfaces ◽  
Three Dimensional ◽  
Surface Displacement ◽  
Maximum Displacement ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Von Mises

A numerical three-dimensional contact model is presented to investigate the contact behavior of multilayered elastic-perfectly plastic solids with rough surfaces. The surface displacement and contact pressure distributions are obtained based on the variational principle with fast Fourier transform (FFT)-based scheme. Von Mises yield criterion is used to determine the onset of yield. The effective hardness is modeled and plays role when the local displacement meet the maximum displacement criterion. Simulations are performed to obtain the contact pressures, fractional total contact area, fractional plastic contact area, and surface/subsurface stresses. These contact statistics are analyzed to study the effects of the layer-to-substrate ratios of stiffness and hardness, surface roughness, and layers thickness of rough, two-layered elastic/plastic solids. The results yield insight into the effects of stiffness and hardness of layers and substrates, surface roughness, and applied load on the contact performance. The layer parameters leading to low friction, stiction, and wear are investigated and identified.

Strongly Anisotropic Rough Surfaces

1979 ◽  
Vol 101 (1) ◽  
pp. 15-20 ◽  
Author(s):  
A. W. Bush ◽  
R. D. Gibson ◽  
G. P. Keogh
Keyword(s):  
Random Process ◽  
Rough Surface ◽  
Contact Area ◽  
Process Model ◽  
Rough Surfaces ◽  
Plasticity Index ◽  
Real Contact Area ◽  
Elastic Contact ◽  
Elastic Plastic ◽  
Real Contact

The statistics of a strongly anisotropic rough surface are briefly described. The elastic contact of rough surfaces is treated by approximating the summits of a random process model by parabolic ellipsoids and applying the Hertzian solution for their deformation. Load and real contact area are derived as functions of the separation and for all separations the load is found to be approximately proportional to the contact area. The limits of elastic/plastic contact are discussed in terms of the plasticity index.

Three-Dimensional Elastic-Plastic Fractal Analysis of Surface Adhesion in Microelectromechanical Systems

1998 ◽  
Vol 120 (4) ◽  
pp. 808-813 ◽  
Author(s):  
K. Komvopoulos ◽  
W. Yan
Keyword(s):  
Microelectromechanical Systems ◽  
Van Der Waals ◽  
Three Dimensional ◽  
Surface Adhesion ◽  
Restoring Force ◽  
Elastic Plastic ◽  
Surface Separation ◽  
High Adhesion ◽  
Interfacial Force ◽  
Asperity Deformation

High adhesion is often encountered at contact interfaces of miniaturized devices, known as microelectromechanical systems, due to the development of capillary, electrostatic, and van der Waals attractive forces. In addition, deformation of contacting asperities on opposing surfaces produces a repulsive interfacial force. Permanent surface adhesion (referred to as stiction) occurs when the total interfacial force is attractive and exceeds the micromachine restoring force. In the present study, a three-dimensional fractal topography description is incorporated into an elastic-plastic contact mechanics analysis of asperity deformation. Simulation results revealing the contribution of capillary, electrostatic, van der Waals, and asperity deformation forces to the total interfacial force are presented for silicon/silicon and aluminum/aluminum material systems and different mean surface separation distances. Results demonstrate a pronounced effect of surface roughness on the micromachine critical stiffness required to overcome interfacial adhesion.

scholarly journals A Finite Element-Based Elastic-Plastic Model for the Contact of Rough Surfaces

2011 ◽  
Vol 2011 ◽  
pp. 1-11 ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Finite Element ◽  
Contact Force ◽  
Contact Area ◽  
Rough Surfaces ◽  
Constitutive Relations ◽  
Element Model ◽  
Tangential Component ◽  
Asperity Contact ◽  
Elastic Plastic ◽  
Force Components

Three-dimensional elastic-plastic contact of two nominally flat rough surfaces is considered. Equations governing the shoulder-shoulder contact of asperities are derived based on the asperity constitutive relations from a finite element model of the elastic-plastic interaction proposed by Kogut and Etsion (2002), in which asperity scale constitutive relations are derived using piecewise approximate functions. An analytical fusion technique is developed to combine the piecewise asperity level constitutive relations. Shoulder-shoulder asperity contact yields a slanted contact force consisting of two components, one in the normal direction and a half-plane tangential component. Statistical summation of the asperity level contact force components and asperity level contact area results in the total contact force and total contact area formulae between two rough surfaces. Approximate equations are developed in closed form for contact force components and contact area.

Closed-Form Equations for Three Dimensional Elastic-Plastic Contact of Nominally Flat Rough Surfaces

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Closed Form ◽  
Contact Force ◽  
Rough Surfaces ◽  
Tangential Force ◽  
Three Dimensional ◽  
Tangential Direction ◽  
Asperity Contact ◽  
Force Component ◽  
Elastic Plastic ◽  
Functional Forms

Approximate closed-form equations governing the shoulder-shoulder contact of asperities are derived based on a generalization by Chang, Etsion, and Bogy. The work entails the consideration of asperity shoulder-shoulder contact in which the volume conservation is assumed in the plastic flow regime. Shoulder-shoulder asperity contact gives rise to a slanted contact force comprising tangential and normal components. Each force component comprises elastic and plastic terms, which upon statistical summation yields the force component for the elastic and plastic forces for the contact of two rough surfaces. Half-plane tangential force due to elastic-plastic contact is derived through the statistical summation of tangential force component along an arbitrary tangential direction. Two sets of equations are found. In the first set of equations the functional forms are simpler and provide approximation of contact force to within 9%. The second set is enhanced equations derived from the first set of approximate equations that achieve an accuracy of within 0.2%.

scholarly journals EFFECT OF RATIO OF MATERIAL HARDNESSES, AVERAGE PRESSURE AND ROUGHNESS PARAMETERS ON ACTUAL CONTACT AREA OF ASSEMBLED SURFACES

2021 ◽  
pp. 32-36
Author(s):  
M. M. Matlin ◽  
V. A. Kazankin ◽  
E. N. Kazankina ◽  
E. V. Kapinosova
Keyword(s):  
Contact Area ◽  
Rough Surfaces ◽  
Average Pressure ◽  
Roughness Parameters ◽  
Actual Contact ◽  
Actual Contact Area ◽  
Elastic Plastic

The paper describes the influence of various factors, including the ratio of hardness, average pressure, radius of microasperities of the surface, affecting the value of the actual contact area of rough surfaces of flat parts mated in fixed joints. The study was carried out using the dependences obtained by the authors describing the elastic-plastic contact of rough surfaces.

A Three-Dimensional Thermomechanical Model of Contact Between Non-Conforming Rough Surfaces

2000 ◽  
Vol 123 (1) ◽  
pp. 17-26 ◽  
Author(s):  
Shuangbiao Liu ◽  
Qian Wang
Keyword(s):  
Rough Surfaces ◽  
Frictional Heating ◽  
Three Dimensional ◽  
Point Contact ◽  
Numerical Algorithms ◽  
Normal Surface ◽  
Thermomechanical Model ◽  
Influence Coefficients ◽  
Surface Displacements ◽  
Thermomechanical Contact

A necessary step in understanding failure problems of tribological elements is to investigate the contact performance of rough surfaces subjected to frictional heating. It is essential that the interfacial variables are obtained through solving the interactive thermomechanical contact problem. This paper studies the three dimensional thermomechanical contact of non-conforming rough surfaces, the model of which includes the normal surface displacements caused by the contact pressure, frictional shear, and frictional heating. Influence coefficients and frequency response functions for elastic and thermoelastic displacements, as well as those for temperature rises, are investigated for model construction. In order to develop an accurate and efficient solver, the numerical algorithms with the discrete convolution and fast Fourier transform techniques and the single-loop conjugated gradient method are used. The model modules are numerically verified and the thermomechanical performance of the rough surfaces in a point contact is studied.

A three-dimensional fractal theory based on thermal contact conductance model of rough surfaces

2017 ◽  
Vol 232 (5) ◽  
pp. 528-539 ◽  
Author(s):  
Yongsheng Zhao ◽  
Cui Fang ◽  
Ligang Cai ◽  
Zhifeng Liu
Keyword(s):  
Rough Surfaces ◽  
Fractal Theory ◽  
Thermal Contact ◽  
Three Dimensional ◽  
Thermal Conductance ◽  
Engineering Application ◽  
Thermal Contact Conductance ◽  
Real Contact Area ◽  
Contact Conductance ◽  
Elastic Plastic

The thermal contact conductance is an important problem in the field of heat transfer. In this research, a three-dimensional fractal theory based on the thermal contact conductance model is presented. The topography of the contact surfaces was fractal featured and determined by fractal parameters. The asperities in the microscale were considered as elastic, elastic-plastic, or plastic deformations. The real contact area of the asperities could be obtained based on the Hertz contact theory. It was assumed that the rough contact surface was composed of numerous discrete and parallel microcontact cylinders. Consequently, the thermal contact conductance of the surface roughness was composed of the thermal constriction conductance of microcontacts and the air medium thermal conductance of microgaps. The thermal contact conductance of rough surfaces could be calculated by the microasperities integration. An experimental set-up with annular interface was designed to verify the presented thermal contact conductance model. Three materials were used for the thermal contact conductance analysis with different fractal dimensions D and fractal roughness parameters G. The numerical results demonstrated that the thermal contact conductance could be affected by the elastic-plastic deformation of the asperities and the gap thermal conductance should not be ignored under the lower contact load. The presented model would provide a theoretical basis for thermal transfer engineering application.

Sign in / Sign up

Export Citation Format

Share Document