Optimum Surface Profile for the Enclosed Pocket Hydrodynamic Gas Thrust Bearing

1970 ◽  
Vol 92 (2) ◽  
pp. 318-324 ◽  
Author(s):  
C. Y. Chow ◽  
H. S. Cheng ◽  
D. F. Wilcock
Keyword(s):  
Finite Difference Method ◽  
Carrying Capacity ◽  
Geometrical Parameter ◽  
Thrust Bearing ◽  
Surface Profile ◽  
Design Procedure ◽  
Load Carrying Capacity ◽  
Relative Importance ◽  
Load Carrying ◽  
The Finite Difference Method

The relative importance, with respect to load-carrying capacity, of each geometrical parameter in a self-lubricated thrust bearing, with an enclosed pocket, is examined at Λ = 0.55. The bearing geometries, including the pocket configurations, for three types of film profiles are optimized. The film profiles in the pocket considered are flat-step, tapered, and taper-step, Fig. 1. Of these three profiles of film, the taper-step film, in an enclosed-pocket bearing, offers the best load-carrying capacity. The variations of load versus each geometrical parameter are shown graphically to facilitate design procedure. These results are obtained from the solution of Reynold’s equation for a compressible fluid film as approximated by the finite-difference method [5]. The load-carrying capacity of an enclosed-pocket bearing with taper-step profile can be significantly higher than that of a bearing with the spiral-grooved pattern under the conditions investigated.

Density Variation Effects in Stepped-Thrust Bearings

1959 ◽  
Vol 26 (3) ◽  
pp. 337-340
Author(s):  
C. F. Kettleborough
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Density Variation ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
The Coefficient Of Friction

Abstract The problem of the stepped-thrust bearing is considered but, whereas normally volumetric continuity is assumed, the equations are solved assuming mass continuity; i.e., the variation of density is also considered as well as the effect of the stepped discontinuity on the load-carrying capacity and the coefficient of friction. Computed theoretical curves illustrate the importance of the density on the operation of this bearing and, in part, explain results already published.

Deformation Effects on the Load Carrying Capacity of the Barrel Bearing in Axial Piston Pumps and Motors

2006 ◽  
Author(s):  
Peter A. J. Achten ◽  
Marc P. A. Schellekens
Keyword(s):  
Elastic Deformation ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Pressure Profile ◽  
Load Carrying Capacity ◽  
Axial Piston Pumps ◽  
Load Carrying ◽  
Face Seals ◽  
Axial Piston Machine ◽  
Axial Piston

Most hydrostatic pumps and motors apply mechanical face seals, often also acting as a thrust bearing. The load carrying capacity of these bearings is very much dependent on the pressure profile generated in the sealing gap. Previous research, outside pumps and motors, has already shown that the gap pressure profile is largely influenced by small radial deformations of the seal lands. This paper discusses the elastic deformation of pump components and the effects of these deformations on the load carrying capacity of a barrel in an axial piston machine.

Performance characteristics of rectangular aerostatic thrust bearing by conformal mapping

2018 ◽  
Vol 70 (8) ◽  
pp. 1457-1475
Author(s):  
Shang-Han Gao ◽  
Sheng-Long Nong
Keyword(s):  
Conformal Mapping ◽  
Pressure Distribution ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Performance Characteristics ◽  
Load Carrying Capacity ◽  
Möbius Transform ◽  
Content Type ◽  
Air Supply ◽  
Load Carrying

Purpose This paper aims to analyze the pressure distribution of rectangular aerostatic thrust bearing with a single air supply inlet using the complex potential theory and conformal mapping. Design/methodology/approach The Möbius transform is used to map the interior of a rectangle onto the interior of a unit circle, from which the pressure distribution and load carrying capacity are obtained. The calculation results are verified by finite difference method. Findings The constructed Möbius formula is very effective for the performance characteristics researches for the rectangular thrust bearing with a single air supply inlet. In addition, it is also noted that to obtain the optimized load carrying capacity, the square thrust bearing can be adopted. Originality/value The Möbius transform is found suitable to describe the pressure distribution of the rectangular thrust bearing with a single air supply inlet.

Matching the relationship between rotational speed and load-carrying capacity on high-speed and heavy-load hydrostatic thrust bearing

2018 ◽  
Vol 70 (1) ◽  
pp. 8-14 ◽  
Author(s):  
Xiao-dong Yu ◽  
Lei Geng ◽  
Xiao-jun Zheng ◽  
Zi-xuan Wang ◽  
Xiao-gang Wu
Keyword(s):  
Carrying Capacity ◽  
Rotational Speed ◽  
Thrust Bearing ◽  
Lubricating Oil ◽  
Load Carrying Capacity ◽  
Average Pressure ◽  
Content Type ◽  
Oil Film ◽  
Hydrostatic Bearing ◽  
Load Carrying

Purpose Rotational speed and load-carrying capacity are two mutual coupling factors which affect high precision and stable operation of a hydrostatic thrust bearing. The purpose of this paper is to study reasonable matching relationship between the rotational speed and the load-carrying capacity. Design/methodology/approach A mathematical model of relationship between the rotational speed and the load-carrying capacity of the hydrostatic bearing with double-rectangle recess is set up on the basis of the tribology theory and the lubrication theory, and the load and rotational speed characteristics of an oil film temperature field and a pressure field in the hydrostatic bearing are analyzed, reasonable matching relationship between the rotational speed and the load-carrying capacity is deduced and a verification experiment is conducted. Findings By increasing the rotational speed, the oil film temperature increases, the average pressure decreases and the load-carrying capacity decreases. By increasing the load-carrying capacity, the oil film temperature and the average pressure increases and the rotational speed decreases; corresponding certain reasonable matching values are available. Originality/value The load-carrying capacity can be increased and the rotational speed improved by means of reducing the friction area of the oil recess by using low-viscosity lubricating oil and adding more oil film clearance; but, the stiffness of the hydrostatic bearing decreases.

Performance investigation of micro-pocketed textured pad thrust bearing

2018 ◽  
Vol 70 (8) ◽  
pp. 1388-1395 ◽  
Author(s):  
Shipra Aggarwal ◽  
R.K. Pandey
Keyword(s):  
Coefficient Of Friction ◽  
Cross Sections ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Load Carrying Capacity ◽  
Temperature Relation ◽  
Cross Sectional ◽  
Content Type ◽  
Load Carrying ◽  
Coupled Solution

Purpose The purpose of this paper is to conceive a new surface texture incorporating a tiny shape among the micro-pockets (with circular, rectangular, trapezoidal and triangular cross-sections) and dimples (cylindrical, hemispherical and ellipsoidal) for exploring to enhance the maximum possible performance behaviors of sector shape pad thrust bearing. Design/methodology/approach Numerical simulation of hydrodynamically lubricated sector shape textured pad thrust bearing has been presented incorporating thermal and cavitation effects. The coupled solution of governing equations (Reynolds equation, film thickness expression, viscosity–temperature relation, energy equation and Laplace equation) has been achieved using finite difference method and Gauss–Seidel iterative scheme. Findings With new textured pads, higher load-carrying capacity and lower coefficient of friction are obtained in comparison to plain sector shape pad. Texture pattern comprising square cross-sectional pockets yields higher load-carrying capacity and lower coefficient of friction in comparison to other cross-sectional shapes (circular, trapezoidal and triangular) of pockets considered herein. Originality/value This study reports a new texture, which involves micro-pockets of square cross-sectional shapes to improve the performance behavior of sector shape pad thrust bearing. About 75 per cent increase in load carrying capacity and 42 per cent reduction in coefficient of friction have been achieved with pad having new texture in comparison to conventional pad.

scholarly journals Appearance of Hysteresis Phenomena on Hydrodynamic Lubrication in a Seal-Type Thrust Bearing with Dimples

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5222
Author(s):  
Reo Miwa ◽  
Norifumi Miyanaga ◽  
Jun Tomioka
Keyword(s):  
Carrying Capacity ◽  
Thrust Bearing ◽  
Hydrodynamic Lubrication ◽  
Frictional Torque ◽  
Hysteresis Phenomenon ◽  
Load Carrying Capacity ◽  
Cavitation Bubbles ◽  
Load Carrying ◽  
The Difference ◽  
Hysteresis Phenomena

This paper described unique hysteresis phenomena that appear in the hydrodynamic lubrication properties of dimpled thrust bearings. A seal-type thrust bearing specimen was textured with dimples. The load-carrying capacity and frictional torque were measured with a constant film thickness and compared to those of a dimple-free specimen. For examining the size of cavitation bubbles that occurred in various conditions, the lubricating area was observed during experiments. The used dimpled specimen produced the load-carrying capacity, and it exhibited an interesting hysteresis phenomenon, the difference in the values in the increasing and decreasing processes of rotational speed. The visualization test results revealed that the size of cavitation bubbles occurring within the dimples strongly affected this phenomenon. In addition, the dimpled specimen was able to reduce the frictional torque compared to the dimple-free specimen. However, the frictional torque did not show the hysteresis loop similar to that shown in the load-carrying capacity.

The Impact of Linear Deformations on Stationary Hydrostatic Thrust Bearings

2002 ◽  
Vol 124 (4) ◽  
pp. 874-877 ◽  
Author(s):  
Noah D. Manring ◽  
Robert E. Johnson ◽  
Harish P. Cherukuri
Keyword(s):  
Pressure Distribution ◽  
Closed Form ◽  
Flow Rate ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Number Flow ◽  
The Impact

In this work, the operating sensitivity of the hydrostatic thrust bearing with respect to pressure-induced deformations will be studied in a stationary setting. Using the classical lubrication equations for low Reynold’s number flow, closed-form expressions are generated for describing the pressure distribution, the flow rate, and the load carrying capacity of the bearing. These expressions are developed to consider deformations of the bearing that result in either concave or convex shapes relative to a flat thrust surface. The impact of both shapes is compared, and the sensitivity of the flow rate and the load carrying capacity of the bearing with respect to the magnitude of the deformation is discussed. In summary, it is shown that all deformations increase the flow rate of the bearing and that concave deformations increase the load carrying capacity while convex deformations decrease this same quantity relative to a non-deformed bearing condition.

Analytical Solutions for Incompressible Spiral Groove Viscous Pumps

1974 ◽  
Vol 96 (3) ◽  
pp. 365-369 ◽  
Author(s):  
F. C. Hsing
Keyword(s):  
Carrying Capacity ◽  
Thrust Bearing ◽  
Present Theory ◽  
Load Carrying Capacity ◽  
Governing Equations ◽  
Spiral Groove ◽  
Design Charts ◽  
Load Carrying ◽  
Analytical Expressions ◽  
Dynamic Perturbation

Exact solutions for a class of incompressible spiral-grooved viscous pumps were obtained by solving the dynamic perturbation equations based on the governing equations of the well-known narrow groove theory. The resulting closed-form analytical expressions contain two integration constants which can be determined by appropriate boundary conditions pertinent to a specific application and design. A flat thrust bearing was chosen to illustrate the application of these results. The load-carrying capacity calculated from present theory was compared with those obtained by other investigator [2]. The agreement is extremely good. No attempt was made to generate design charts for various designs since the resulting expressions obtained in this work can be used quite easily in a straightforward fashion.

The Effect of Rotational Speed on Fluid Compressibility and Gap Pressure of a Partially Porous Aerostatic Thrust Bearing

2015 ◽  
Vol 642 ◽  
pp. 311-316
Author(s):  
Te Yen Huang ◽  
Sheam Chyun Lin ◽  
Song Chiang Shen ◽  
Shao Yu Hsu
Keyword(s):  
Carrying Capacity ◽  
Thrust Bearing ◽  
Stokes Equations ◽  
Air Flow ◽  
Air Gap ◽  
Spindle Speed ◽  
Positive Pressure ◽  
Coupling Scheme ◽  
Load Carrying Capacity ◽  
Load Carrying

This study investigated the effect of the spindle speed on pressure distribution in the air gap and the load carrying capacity of a porous aerostatic annular thrust bearing. Based on the finite volume method and the pressure-velocity coupling scheme of the SIMPLE algorithm with the standard k-ε turbulent model, a CFD software was used to solve the Navier-Stokes equations to calculate pressure and velocity of the air flow. The results revealed there were positive pressure zones and vacuum pressure zones in the air gap between the thrust disk and the bearing. Under the same spindle speed, the pressure difference between the positive peak and the negative peak in the case of incompressible air was greater than that in the case of compressible air. The averaged pressure on the surface of the thrust disk with compressible air flow was higher than that with incompressible air flow. So was the load carrying capacity of the bearing, which increased when the spindle rotated faster.

The Dual Action Gas Thrust Bearing—A New High Load Bearing Concept

1977 ◽  
Vol 99 (1) ◽  
pp. 89-94
Author(s):  
I. Etsion
Keyword(s):  
Numerical Solution ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Load Capacity ◽  
High Load ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Dual Action ◽  
Hydrodynamic Effects

The principle of utilizing hydrodynamic effects in diverging films for improving load capacity in gas thrust bearings is discussed. A new concept of dual action bearing based on that principle is described and analyzed. The potential of the new bearing is demonstrated both analytically for an infinitely long slider and by numerical solution for a flat sector shaped thrust bearing. It is shown that the dual action bearing can extend substantially the range of load carrying capacity in gas lubricated thrust bearings and improve their efficiency.

Sign in / Sign up

Export Citation Format

Share Document