Adiabatic and Overall Effectiveness for the Showerhead Film Cooling of a Turbine Vane

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Marc L. Nathan ◽  
Thomas E. Dyson ◽  
David G. Bogard ◽  
Sean D. Bradshaw
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Internal Heat ◽  
Flux Ratio ◽  
Coolant Temperature ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Turbine Vane ◽  
Dynamics Simulations ◽  
Overall Effectiveness

There have been a number of previous studies of the adiabatic film effectiveness for the showerhead region of a turbine vane, but no previous studies of the overall cooling effectiveness. The overall cooling effectiveness is a measure of the external surface temperature relative to the mainstream temperature and the inlet coolant temperature, and consequently is a direct measure of how effectively the surface is cooled. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components, and the internal cooling is designed so that the ratio of the external to internal heat transfer coefficient is matched to that of the engine. In this study, the overall effectiveness was experimentally measured on a model turbine vane constructed of a material to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. The cooling design consisted of a showerhead composed of five rows of holes with one additional row on both pressure and suction sides of the vane. An identical model was also constructed out of low conductivity foam to measure adiabatic film effectiveness. Of particular interest in this study was to use the overall cooling effectiveness measurements to identify local hot spots which might lead to failure of the vane. Furthermore, the experimental measurements provided an important database for evaluation of computational fluid dynamics simulations of the conjugate heat transfer effects that occur in the showerhead region. Continuous improvement in both measures of performance was demonstrated with increasing momentum flux ratio.

Adiabatic and Overall Effectiveness for the Showerhead Film Cooling of a Turbine Vane

2012 ◽  
Author(s):  
Marc L. Nathan ◽  
Thomas E. Dyson ◽  
David G. Bogard ◽  
Sean D. Bradshaw
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Internal Heat ◽  
Flux Ratio ◽  
Coolant Temperature ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Turbine Vane ◽  
Engine Components ◽  
Overall Effectiveness

There have been a number of previous studies of the adiabatic film effectiveness for the showerhead region of a turbine vane, but no previous studies of the overall cooling effectiveness. The overall cooling effectiveness is a measure of the external surface temperature relative to the mainstream temperature and the inlet coolant temperature, and consequently is a direct measure of how effectively the surface is cooled. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components, and the internal cooling is designed so that the ratio of the external to internal heat transfer coefficient is matched to that of the engine. In this study, the overall effectiveness was experimentally measured on a model turbine vane constructed of a material to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. The cooling design consisted of a showerhead composed of five rows of holes with one additional row on both pressure and suction sides of the vane. An identical model was also constructed out of low conductivity foam to measure adiabatic film effectiveness. Of particular interest in this study was to use the overall cooling effectiveness measurements to identify local hot spots which might lead to failure of the vane. Furthermore, the experimental measurements provided an important database for evaluation of CFD simulations of the conjugate heat transfer effects that occur in the showerhead region. Continuous improvement in both measures of performance was demonstrated with increasing momentum flux ratio.

Adiabatic and Overall Effectiveness for a Fully Cooled Turbine Vane

2013 ◽  
Author(s):  
Thomas E. Dyson ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Sean D. Bradshaw
Keyword(s):  
Biot Number ◽  
Film Cooling ◽  
Large Scale ◽  
Internal Heat ◽  
Coolant Temperature ◽  
Internal Cooling ◽  
Impingement Cooling ◽  
Turbine Vane ◽  
Cooling Design ◽  
Overall Effectiveness

Adiabatic and overall effectiveness data were measured for a fully cooled, scaled up turbine vane model in a low speed linear cascade with a chord-exit Reynolds number of 700,000. The overall effectiveness is a measure of the external surface temperature relative to the mainstream temperature and the inlet coolant temperature, and consequently is a direct measure of how effectively the surface is cooled. This can be determined experimentally when the experimental model is constructed so that the Biot number of the model and the ratio of the external to internal heat transfer coefficient are chosen so that the model has a similar thermal behavior to that of an actual engine component. The model used in this study had a cooling design that consisted of 149 total coolant holes in 13 rows, including a showerhead containing five rows of holes. The model also incorporated an internal impingement cooling configuration. An identical model was also constructed out of low conductivity foam to measure adiabatic effectiveness. This is the first study to use a large scale, matched Biot number model to measure engine representative overall effectiveness for a vane employing full coverage film cooling. The focus of this research was to determine the relative contributions of the external and internal cooling, and to serve as a baseline for validation of computational simulations. Additionally, a simplified model using measurements of overall effectiveness with internal cooling alone was used to predict overall effectiveness downstream of the showerhead.

Influence of Coolant on Cooling Performance Sensitivity of Internally Convective Turbine Vane

2021 ◽  
Author(s):  
Thanapat Chotroongruang ◽  
Prasert Prapamonthon ◽  
Rungsimun Thongdee ◽  
Thanapat Thongmuenwaiyathon ◽  
Zhenxu Sun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Turbine Engine ◽  
Performance Sensitivity ◽  
Turbine Vane ◽  
Cooling Air

Abstract Based on the Brayton cycle for gas-turbine engines, the high thermal efficiency and power output of a gas-turbine engine can be obtainable when the gas-turbine engine operates at high turbine inlet temperatures. However, turbine components e.g., inlet guide vane, rotor blade, and stator vane request high cooling performance. Typically, internal cooling and film cooling are two effective techniques that are widely used to protect high thermal loads for the turbine components in a state-of-the-art gas turbine. Consequently, the high thermal efficiency and power output can be obtained, and the turbine lifespan can be prolonged, also. On top of that, a comprehensive understanding of flow and heat transfer phenomena in the turbine components is very important. As a result, both experiments and simulations have been used to improve the cooling performance of the turbine components. In fact, the cooling air used in the internal cooling and film cooling is partially extracted from the compressor. Therefore, variations in the cooling air affect the cooling performance of the turbine components directly. This paper presents a numerical study on the influence of the cooling air on cooling-performance sensitivity of an internally convective turbine vane, MARK II using the computational fluid dynamics (CFD)/conjugate heat transfer (CHT) with the SST k-ω turbulence model. Result comparisons are conducted in terms of pressure, temperature, and cooling effectiveness under the effects of the inlet temperature, mass flow rate, turbulence intensity, and flow direction of the cooling air. The cooling-performance sensitivity to the coolant parameters is shown through variations of local cooling effectiveness, and area and volume-weighted average cooling effectiveness.

Adiabatic Film Cooling Effectiveness From Heat Transfer Measurements in Compressible, Variable-Property Flow

1985 ◽  
Vol 107 (2) ◽  
pp. 313-320 ◽  
Author(s):  
P. M. Ligrani ◽  
C. Camci
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Velocity Ratio ◽  
Flux Ratio ◽  
Coolant Temperature ◽  
Transfer Coefficients ◽  
Constant Property ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Variable Property

A variable property correction is given for turbulent boundary layers that are film-cooled using staggered rows of injection holes inclined at 35 deg. With the correction, a relation is provided between the adiabatic film cooling effectiveness for constant property flow and heat transfer coefficients for variable property flow, which are based on the difference between the freestream recovery temperature and wall temperature. The variable property correction was determined from heat transfer measurements for a range of injection parameters at different values of the nondimensional coolant temperature and from results in the literature. Because the flow is compressible, the importance of the injection mass flux ratio, momentum flux ratio, and velocity ratio are considered in the determination of effectiveness.

Full Thermal Experimental Assessment of a Dendritic Turbine Vane Cooling Scheme

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
S. Luque ◽  
J. Batstone ◽  
D. R. H. Gillespie ◽  
T. Povey ◽  
E. Romero
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Pressure Ratio ◽  
Internal Heat ◽  
Flux Ratio ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Experimental Assessment ◽  
Film Cooling Effectiveness ◽  
Internal Heat Transfer

A full thermal experimental assessment of a novel dendritic cooling scheme for high-pressure turbine vanes has been conducted and is presented in this paper, including a comparison to the current state-of-the-art cooling arrangement for these components. The dendritic cooling system consists of cooling holes with multiple internal branches that enhance internal heat transfer and reduce the blowing ratio at hole exit. Three sets of measurements are presented, which describe, first, the local internal heat transfer coefficient of these structures and, secondly, the cooling flow capacity requirements and overall cooling effectiveness of a highly engine-representative dendritic geometry. Full-coverage surface maps of overall cooling effectiveness were acquired for both dendritic and baseline vanes in the Annular Sector Heat Transfer Facility, where scaled near-engine conditions of Mach number, Reynolds number, inlet turbulence intensity, and coolant-to-mainstream pressure ratio (or momentum flux ratio) are achieved. Engine hardware was used, with laser-sintered metal counterparts for the novel cooling geometry (their detailed configuration, design, and manufacture are discussed). The dendritic system will be shown to offer improved overall cooling effectiveness at a reduced cooling mass flow rate due to a more uniform film cooling effectiveness, a decreased tendency for films to lift off in regions of low external cross flow, improved through-wall heat transfer and internal cooling efficiency, increased internal wetted surface area of the cooling holes, and the enhanced turbulence induced in them.

Sensitivity of the Overall Effectiveness to Film Cooling and Internal Cooling on a Turbine Vane Suction Side

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Randall P. Williams ◽  
Thomas E. Dyson ◽  
David G. Bogard ◽  
Sean D. Bradshaw
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Suction Side ◽  
Coolant Temperature ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Impingement Cooling ◽  
Turbine Vane ◽  
Cooling Effects ◽  
Engine Components

The overall cooling effectiveness for a turbine airfoil was quantified based on the external surface temperature relative to the mainstream temperature and the inlet coolant temperature. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components. In this study, the overall cooling effectiveness was experimentally measured on a model turbine vane constructed of a material deigned to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. Overall cooling effectiveness and adiabatic film effectiveness were measured downstream of a single row of round holes positioned on the suction side of the vane. Experiments were conducted to evaluate the cooling effects of internal cooling alone, and then the combined effects of film cooling and internal cooling for a range of coolant flow rates. While the adiabatic film effectiveness decreased when using high momentum flux ratios for the film cooling, due to coolant jet separation, the overall cooling effectiveness increased at higher momentum flux ratios. This increase was due to increased internal cooling effects. Overall cooling effectiveness measurements were also compared to analytical predictions based on a 1D thermal analysis using measured adiabatic film effectiveness and overall cooling effectiveness without film cooling.

Full Thermal Experimental Assessment of a Dendritic Turbine Vane Cooling Scheme

2012 ◽  
Author(s):  
S. Luque ◽  
J. Batstone ◽  
D. R. H. Gillespie ◽  
T. Povey ◽  
E. Romero
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Pressure Ratio ◽  
Internal Heat ◽  
Flux Ratio ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Experimental Assessment ◽  
Film Cooling Effectiveness ◽  
Internal Heat Transfer

A full thermal experimental assessment of a novel dendritic cooling scheme for high-pressure turbine vanes has been conducted and is presented in this paper, including comparisons to the conventional cooling arrangement for these components. The dendritic cooling system consists of cooling holes with multiple internal branches which enhance internal heat transfer and reduce the blowing ratio at hole exit. Three sets of measurements are presented, which describe, first, the local internal heat transfer coefficient of these structures, and, secondly, the cooling flow capacity requirements and overall cooling effectiveness of a highly engine-representative dendritic geometry. Full-coverage surface maps of overall cooling effectiveness were acquired for both dendritic and baseline vanes in the Annular Sector Heat Transfer Facility, where scaled near-engine conditions of Mach number, Reynolds number, inlet turbulence intensity and coolant-to-mainstream pressure ratio (or momentum flux ratio) are achieved. Engine hardware was used, with laser-sintered metal counterparts for the novel cooling geometry (their detailed configuration, design, and manufacture are discussed). The dendritic system will be shown to offer improved overall cooling effectiveness at a reduced cooling mass flow rate due to a more uniform film cooling effectiveness, a decreased tendency for films to lift off in regions of low external cross flow, improved through-wall heat transfer and internal cooling efficiency, increased internal wetted surface area of the cooling holes, and the enhanced turbulence induced in them.

Sensitivity of the Overall Effectiveness to Film Cooling and Internal Cooling on a Turbine Vane Suction Side

2012 ◽  
Author(s):  
Randall P. Williams ◽  
Thomas E. Dyson ◽  
David G. Bogard ◽  
Sean D. Bradshaw
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Suction Side ◽  
Coolant Temperature ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Impingement Cooling ◽  
Turbine Vane ◽  
Cooling Effects ◽  
Engine Components

The overall cooling effectiveness for a turbine airfoil was quantified based on the external surface temperature relative to the mainstream temperature and the inlet coolant temperature. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components. In this study, the overall cooling effectiveness was experimentally measured on a model turbine vane constructed of a material deigned to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. Overall cooling effectiveness and adiabatic film effectiveness were measured downstream of a single row of round holes positioned on the suction side of the vane. Experiments were conducted to evaluate the cooling effects of internal cooling alone, and then the combined effects of film cooling and internal cooling for a range of coolant flow rates. While the adiabatic film effectiveness decreased when using high momentum flux ratios for the film cooling, due to coolant jet separation, the overall cooling effectiveness increased at higher momentum flux ratios. This increase was due to increased internal cooling effects. Overall cooling effectiveness measurements were also compared to analytical predictions based on a 1D thermal analysis using measured adiabatic film effectiveness and overall cooling effectiveness without film cooling.

Overall Cooling Effectiveness Characteristic and Influence Mechanism on an Endwall With Film Cooling and Impingement

2015 ◽  
Author(s):  
Mingfei Li ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Internal Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
One Dimensional ◽  
Influence Mechanism ◽  
Endwall Cooling ◽  
Internal Heat Transfer

The cooling system is required to ensure gas turbine can work at high temperature, which has exceeded the material limitation. An endwall cooling test rig was built up to conduct the endwall cooling research. A detailed work was done for analyzing characteristics of endwall heat transfer and discussing the multi-parameter influence mechanism of overall cooling effectiveness. The main flow side heat transfer coefficient, adiabatic film cooling effectiveness and overall cooling effectiveness were measured in the experiments. The effects of coolant mass flowrate ratio (MFR) were considered through the measurement. In order to analyze how each of the parameters works on overall cooling effectiveness, a one-dimensional correlation was developed. The results showed that obvious enhancement could be found in cooling effectiveness by increasing coolant MFR, and the film jet can be easily attached to the surface after the acceleration of the main flow in the nozzle channel. Comparing with film cooling effectiveness, overall cooling effectiveness distribution is more uniform, which is due to the influence of internal cooling. The verified one-dimensional analysis method showed that the improvement in film cooling would be most efficient to heighten overall cooling effectiveness. The improvement in film cooling would be more efficient when film cooling effectiveness is in high level than in low level. However, the enhancement of internal heat transfer is more efficient when internal heat transfer coefficient is low.

Experimental Evaluations of the Relative Contributions to Overall Effectiveness in Turbine Blade Leading Edge Cooling

2018 ◽  
Author(s):  
Carol E. Bryant ◽  
Connor J. Wiese ◽  
James L. Rutledge ◽  
Marc D. Polanka
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Leading Edge ◽  
Internal Surface ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Impingement Cooling ◽  
External Cooling ◽  
Turbine Component ◽  
Overall Effectiveness

Gas turbine hot gas path components are protected through a combination of internal cooling and external film cooling. The coolant typically travels through internal passageways, which may involve impingement on the internal surface of a turbine component, before being ejected as film cooling. Internal cooling effects have been studied in facilities that allow measurement of heat transfer coefficients within models of the internal cooling paths, with large heat transfer coefficients generally desirable. External film cooling is typically evaluated through measurements of the adiabatic effectiveness and its effect on the external heat transfer coefficient. Efforts aimed at improving cooling are often focused on either only the internal cooling or the film cooling; however, the common coolant flow means the internal and external cooling schemes are linked and the coolant holes themselves provide another convective path for heat transfer to the coolant. Recently, measurements of overall cooling effectiveness using matched Biot number turbine component models allow evaluation of the nondimensional wall temperature achieved for the fully cooled component. However, the relative contributions of internal cooling, external cooling, and convection within the film cooling holes is not well understood. Large scale, matched Biot number experiments, complemented by CFD simulations, were performed on a fully film cooled cylindrical leading edge model to evaluate the effects of various alterations in the cooling design on the overall effectiveness. The relative influence of film cooling and cooling within the holes was evaluated by selectively disabling individual holes and quantifying how the overall effectiveness changed. Several internal impingement cooling schemes in addition to a baseline case without impingement cooling were also tested. In general, impingement cooling is shown to have a negligible influence on the overall effectiveness in the showerhead region. This indicates that the cost and pressure drop penalties for implementing impingement cooling may not be compensated by an increase in thermal performance. Instead, the internal cooling provided by convection within the holes themselves was shown, along with external film cooling, to be a dominant contribution to the overall cooling effectiveness. Indeed, the numerous holes within the showerhead region impede the ability of internal surface cooling schemes to influence the outside surface temperature. The results of this research may allow improved focus of future efforts on the forms of cooling with the greatest potential to improve cooling performance.

Sign in / Sign up

Export Citation Format

Share Document