Operability Limits of Tubular Injectors With Vortex Generators for a Hydrogen-Fueled Recuperated 100 kW Class Gas Turbine

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Stefan Bauer ◽  
Balbina Hampel ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Bulk Flow ◽  
Vortex Generators ◽  
Inlet Temperature ◽  
Test Rig ◽  
Temperature Range ◽  
Wide Range

Abstract Vortex generators are known to be effective in augmenting the mixing of fuel jets with air. The configuration investigated in this study is a tubular air passage with fuel injection from one single orifice placed in the side wall. In the range of typical gas turbine combustor inlet temperatures, the performance vortex generator premixers (VGPs) have already been investigated for natural gas as well as for blends of natural gas and hydrogen. However, for highly reactive fuels, the application of VGPs in recuperated gas turbines is particularly challenging because the high combustor inlet temperature leads to potential risk with regard to premature self-ignition and flame flashback. As the current knowledge does not cover the temperature range far above the self-ignition temperature, an experimental investigation of the operational limits of VGPs is currently being conducted at the Thermodynamics Institute of the Technical University of Munich, Garching, Germany, which is particularly focused on reactive fuels and the thermodynamic conditions present in recuperated gas turbines with pressure ratios of 4–5. For the study presented in this paper, an atmospheric combustion VGP test rig has been designed, which facilitates investigations in a wide range of operating conditions in order to comply with the situation in recuperated microgas turbines (MGT), namely, global equivalence ratios between 0.2 and 0.7, air preheating temperatures between 288 K and 1100 K, and air bulk flow rates between 6 and 16 g/s. Both the entire mixing zone in the VGP and the primary combustion zone of the test rig are optically accessible. High-speed OH* chemiluminescence imaging is used for the detection of the flashback and blow-off limits of the investigated VGPs. Flashback and blow-off limits of hydrogen in a wide temperature range covering the autoignition regime are presented, addressing the influences of equivalence ratio, air preheating temperature, and momentum ratio between air and hydrogen on the operational limits in terms of bulk flow velocity. It is shown that flashback and blow-off limits are increasingly influenced by autoignition in the ultrahigh temperature regime.

Operability Limits of Tubular Injectors With Vortex Generators for a Hydrogen Fuelled Recuperated 100kW Class Gas Turbine

2016 ◽  
Author(s):  
Stefan Bauer ◽  
Balbina Hampel ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Bulk Flow ◽  
Vortex Generators ◽  
Test Rig ◽  
Temperature Range ◽  
Auto Ignition ◽  
Wide Range

Vortex generators are known to be effective in augmenting the mixing of fuel jets with air. The configuration investgated in this study is a tubular air passage with fuel injection from one single orifice placed in the side wall. In the range of typical gas turbine combustor inlet temperatures, the performance vortex generator premixers (VGPs) have already been investigated for natural gas as well as for blends of natural gas and hydrogen. However, for highly reactive fuels, the application of VGPs in recuperated gas turbines is particularly challenging because the high combustor inlet temperature leads to potential risk with regard to premature self-ignition and flame flashback. As the current knowledge does not cover the temperature range far above the self-ignition temperature, an experimental investigation of the operational limits of VGPs is currently being conducted at the Thermodynamics Institute of the Technical University of Munich, which is particularly focused on reactive fuels and the thermodynamic conditions present in recuperated gas turbines with pressure ratios of 4–5. For the study presented in the paper, an atmospheric combustion VGP test rig has been designed, which facilitates investigations in a wide range of operating conditions in order to comply with the situation in recuperated micro gas turbines, namely global equivalence ratios between 0.2 and 0.7, air preheating temperatures between 288K and 1100K, and air bulk flow rates between 6–16 g/s. Both the entire mixing zone in the VGP and the primary combustion zone of the test rig are optically accessible. High speed OH* chemiluminescence imaging is used for the detection of the flashback and blow-off limits of the investigated VGPs. Flashback and blow-off limits of hydrogen in a wide temperature range covering the auto-ignition regime are presented, addressing the influences of equivalence ratio, air preheating temperature and momentum ratio between air and hydrogen on the operational limits in terms of bulk flow velocity. It is shown that flashback and blow-off limits are increasingly influenced by auto-ignition in the ultra-high temperature regime.

Flameholding Tendencies of Natural Gas and Hydrogen Flames at Gas Turbine Premixer Conditions

2014 ◽  
Author(s):  
Elliot Sullivan-Lewis ◽  
Vincent McDonell
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
High Reliability ◽  
Elevated Pressure ◽  
Inlet Temperature ◽  
Increased Risk ◽  
Wide Range ◽  
Lean Premixed

Ground based gas turbines are responsible for generating a significant amount of electric power as well as providing mechanical power for a variety of applications. This is due to their high efficiency, high power density, high reliability, and ability to operate on a wide range of fuels. Due to increasingly stringent air quality requirements, stationary power gas turbines have moved to lean-premixed operation. Lean-premixed operation maintains low combustion temperatures for a given turbine inlet temperature, resulting in low NOx emissions while minimizing emissions of CO and hydrocarbons. In addition, to increase overall cycle efficiency, engines are being operated at higher pressure ratios and/or higher combustor inlet temperatures. Increasing combustor inlet temperatures and pressures in combination with lean-premixed operation leads to increased reactivity of the fuel/air mixture, leading to increased risk of potentially damaging flashback. Curtailing flashback on engines operated on hydrocarbon fuels requires care in design of the premixer. Curtailing flashback becomes more challenging when fuels with reactive components such as hydrogen are considered. Such fuels are gaining interest because they can be generated from both conventional and renewable sources and can be blended with natural gas as a means for storage of renewably generated hydrogen. The two main approaches for coping with flashback are either to design a combustor that is resistant to flashback, or to design one that will not anchor a flame if a flashback occurs. An experiment was constructed to determine the flameholding tendencies of various fuels on typical features found in premixer passage ways (spokes, steps, etc.) at conditions representative of a gas turbine premixer passage way. In the present work tests were conducted for natural gas and hydrogen between 3 and 9 atm, between 530 K and 650K, and free stream velocities from 40 to 100 m/s. Features considered in the present study include a spoke in the center of the channel and a step at the wall. The results are used in conjunction with existing blowoff correlations to evaluate flameholding propensity of these physical features over the range of conditions studied. The results illustrate that correlations that collapse data obtained at atmospheric pressure do not capture trends observed for spoke and wall step features at elevated pressure conditions. Also, a notable fuel compositional effect is observed.

Gas Turbine Fouling: The Influence of Climate and Part-Load Operating Conditions

2019 ◽  
Author(s):  
Nicola Aldi ◽  
Nicola Casari ◽  
Mirko Morini ◽  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
...  
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Environmental Influence ◽  
Electrical Power ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Continuous Increase ◽  
Part Load

Abstract Energy and climate change policies associated with the continuous increase in natural gas costs pushed governments to invest in renewable energy and alternative fuels. In this perspective, the idea to convert gas turbines from natural gas to syngas from biomass gasification could be a suitable choice. Biogas is a valid alternative to natural gas because of its low costs, high availability and low environmental impact. Syngas is produced with the gasification of plant and animal wastes and then burnt in gas turbine combustor. Although synfuels are cleaned and filtered before entering the turbine combustor, impurities are not completely removed. Therefore, the high temperature reached in the turbine nozzle can lead to the deposition of contaminants onto internal surfaces. This phenomenon leads to the degradation of the hot parts of the gas turbine and consequently to the loss of performance. The amount of the deposited particles depends on mass flow rate, composition and ash content of the fuel and on turbine inlet temperature (TIT). Furthermore, compressor fouling plays a major role in the degradation of the gas turbine. In fact, particles that pass through the inlet filters, enter the compressor and could deposit on the airfoil. In this paper, the comparison between five (5) heavy-duty gas turbines is presented. The five machines cover an electrical power range from 1 MW to 10 MW. Every model has been simulated in six different climate zones and with four different synfuels. The combination of turbine fouling, compressor fouling, and environmental conditions is presented to show how these parameters can affect the performance and degradation of the machines. The results related to environmental influence are shown quantitatively, while those connected to turbine and compressor fouling are reported in a more qualitative manner. Particular attention is given also to part-load conditions. The power units are simulated in two different operating conditions: 100 % and 80 % of power rate. The influence of this variation on the intensity of fouling is also reported.

Flameholding Tendencies of Natural Gas and Hydrogen Flames at Gas Turbine Premixer Conditions

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Elliot Sullivan-Lewis ◽  
Vince McDonell
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
High Reliability ◽  
Elevated Pressure ◽  
Inlet Temperature ◽  
Increased Risk ◽  
Wide Range ◽  
Lean Premixed

Ground-based gas turbines are responsible for generating a significant amount of electric power as well as providing mechanical power for a variety of applications. This is due to their high efficiency, high power density, high reliability, and ability to operate on a wide range of fuels. Due to increasingly stringent air quality requirements, stationary power gas turbines have moved to lean-premixed operation. Lean-premixed operation maintains low combustion temperatures for a given turbine inlet temperature, resulting in low NOx emissions while minimizing emissions of CO and hydrocarbons. In addition, to increase overall cycle efficiency, engines are being operated at higher pressure ratios and/or higher combustor inlet temperatures. Increasing combustor inlet temperatures and pressures in combination with lean-premixed operation leads to increased reactivity of the fuel/air mixture, leading to increased risk of potentially damaging flashback. Curtailing flashback on engines operated on hydrocarbon fuels requires care in design of the premixer. Curtailing flashback becomes more challenging when fuels with reactive components such as hydrogen are considered. Such fuels are gaining interest because they can be generated from both conventional and renewable sources and can be blended with natural gas as a means for storage of renewably generated hydrogen. The two main approaches for coping with flashback are either to design a combustor that is resistant to flashback, or to design one that will not anchor a flame if a flashback occurs. An experiment was constructed to determine the flameholding tendencies of various fuels on typical features found in premixer passage ways (spokes, steps, etc.) at conditions representative of a gas turbine premixer passage way. In the present work, tests were conducted for natural gas and hydrogen between 3 and 9 atm, between 530 K and 650 K, and free stream velocities from 40 to 100 m/s. Features considered in the present study include a spoke in the center of the channel and a step at the wall. The results are used in conjunction with existing blowoff correlations to evaluate flameholding propensity of these physical features over the range of conditions studied. The results illustrate that correlations that collapse data obtained at atmospheric pressure do not capture trends observed for spoke and wall step features at elevated pressure conditions. Also, a notable fuel compositional effect is observed.

Engine Testing of a Natural Gas-Fired, Low-NOx, Variable Geometry Gas Turbine Combustor for a Small Gas Turbine

1996 ◽  
Author(s):  
Shigeru Hayashi ◽  
Hideshi Yamada ◽  
Kazuo Shimodaira
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Nox Emissions ◽  
Variable Geometry ◽  
Wide Range ◽  
Lean Premixed ◽  
Full Power ◽  
Engine Testing

The development of a variable geometry lean-premixed combustor is in progress at NAL. Engine testing has been cooducted by using a natural gas-fueled 210-kW gas turbine to demonstrate the capability of ultra-low NOx emissions over a wide range of eogine operation. This paper describes the effort of engine testing of the combustor to achieve NOx emissions of the 10-ppm level. Fuel was staged to the non-premixed pilot and premixed main burners. A butterfly valve air splitting system was employed to maintain both low NOx emissions and high efficieocy over a wide operating range of the engine. The engioe was operated in the lean-premixed, low NOx emissions mode from idle to full power. Over the whole operating conditions from idle to full power, NOx emissions were reduced to levels less than 25 ppm (15% O2 dry). The NOx emissions level for a nearly constant combustion efficiency decreased with increasing power or turbine inlet temperature. At operating conditions of 90% to full power, NOx emissions levels of 12 to 8 ppm (15% O2 dry) were measured with combustion efficiencies of 99.7 to 99.1%.

Uncertainty Analysis of Inflow Conditions on an HPT Gas Turbine Nozzle: Effect on Particle Deposition

2020 ◽  
Author(s):  
R. Friso ◽  
N. Casari ◽  
M. Pinelli ◽  
A. Suman ◽  
F. Montomoli
Keyword(s):  
Gas Turbine ◽  
Energy Efficient ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Operating Conditions ◽  
Wide Range ◽  
And Performance ◽  
Gas Turbine Nozzle ◽  
The Impact ◽  
Inflow Conditions

Abstract Gas turbines (GT) are often forced to operate in harsh environmental conditions. Therefore, the presence of particles in their flow-path is expected. With this regard, deposition is a problem that severely affects gas turbine operation. Components’ lifetime and performance can dramatically vary as a consequence of this phenomenon. Unfortunately, the operating conditions of the machine can vary in a wide range, and they cannot be treated as deterministic. Their stochastic variations greatly affect the forecasting of life and performance of the components. In this work, the main parameters considered affected by the uncertainty are the circumferential hot core location and the turbulence level at the inlet of the domain. A stochastic analysis is used to predict the degradation of a high-pressure-turbine (HPT) nozzle due to particulate ingestion. The GT’s component analyzed as a reference is the HPT nozzle of the Energy-Efficient Engine (E3). The uncertainty quantification technique used is the probabilistic collocation method (PCM). This work shows the impact of the operating conditions uncertainties on the performance and lifetime reduction due to deposition. Sobol indices are used to identify the most important parameter and its contribution to life. The present analysis enables to build confidence intervals on the deposit profile and on the residual creep-life of the vane.

Ignition Studies of C1-C7 Natural Gas Blends At Gas-Turbine Relevant Conditions

2021 ◽  
Author(s):  
Amrit Sahu ◽  
A.A.E.S Mohamed ◽  
Snehashish Panigrahy ◽  
Gilles Bourque ◽  
Henry Curran
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Mixtures ◽  
Rapid Compression Machine ◽  
Temperature Range ◽  
Auto Ignition ◽  
Wide Range ◽  
Model Predictions ◽  
Detailed Kinetic Model ◽  
Sensitization Effect

Abstract New ignition delay time measurements (IDT) of natural gas mixtures enriched with small amounts of n-hexane and n-heptane were performed in a rapid compression machine to interpret the sensitization effect of heavier hydrocarbons on auto-ignition at gas-turbine relevant conditions. The experimental data of natural gas mixtures containing alkanes from methane to n-heptane were carried out over a wide range of temperatures (840-1050 K), pressures (20-30 bar), and equivalence ratios (f = 0.5 and 1.5). The experiments were complemented with numerical simulations using a detailed kinetic model developed to investigate the effect of n-hexane and n-heptane additions. Model predictions show that the addition of even small amounts (1-2%) of n-hexane and n-heptane can lead to an increase in reactivity by ~40-60 ms at a temperature of 700 K. The IDTs of these mixtures decrease rapidly with an increase in the concentration of up to 7.5% but becomes almost independent of the C6/C7 concentration >10%. This sensitization effect of C6 and C7 is also found to be more pronounced in the temperature range 700-900 K compared to that at higher temperatures (>900 K). The reason is attributed to the dependence of IDT primarily on H2O2(+M)??H+?H (+M) at higher temperatures while the fuel-dependent reactions such as H-atom abstraction, RO2 dissociation, or Q OOH+O2 reactions are less important compared to the temperature range 700-900 K, where they are very important.

Evaluation of GT Outboard Bleed Air on Overall Engine Efficiency and CO2e Emission in Natural Gas Compressor Stations

2013 ◽  
Author(s):  
K. K. Botros ◽  
H. Golshan ◽  
D. Rogers ◽  
B. Sloof
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Heat Rate ◽  
Operating Conditions ◽  
Process Conditions ◽  
Inlet Temperature ◽  
Predictive Tool ◽  
Valve Opening ◽  
Overall Efficiency ◽  
Engine Emission

Gas turbine (GT) engines employed in natural gas compressor stations operate in different modes depending on the power, turbine inlet temperature and shaft speeds. These modes apply different sequencing of bleed valve opening on the air compressor side of the engine. Improper selection of the GT and the driven centrifugal gas compressor operating conditions can lead to larger bleed losses due to wider bleed valve openings. The bleed loss inevitably manifests itself in the form of higher overall heat rate of the GT and greater engine emission. It is therefore imperative to determine and understand the engine and process conditions that drive the GT to operate in these different modes. The ultimate objective is to operate the engine away from the inefficient modes by adjusting the driven gas compressor parameters as well as the overall station operating conditions (i.e. load sharing, control set points, etc.). This paper describes a methodology to couple the operating conditions of the gas compressor to the modes of GT bleed valve opening (and the subsequent air bleed rates) leading to identification of the operating parameters for optimal performance (i.e., best overall efficiency and minimum CO2e emission). A predictive tool is developed to quantify the overall efficiency loss as a result of the different bleed opening modes, and map out the condition on the gas compressor characteristics. One year’s worth of operating data taken from two different compressor stations on TransCanada Pipelines’ Alberta system were used to demonstrate the methodology. The first station employs GE-LM1600 gas turbine driving a Cooper Rolls-RFBB-30 centrifugal compressor. The second station employs GE-LM-2500+ gas turbine driving NP PCL-800/N compressor. The analysis conclusively indicates that there are operating regions on the gas compressor maps where losses due to bleed valves are reduced and hence CO2 emissions are lowered, which presents an opportunity for operation optimization.

Experimental Investigations of Pressure Drop in the Combustion Chamber of Gas Turbine

1989 ◽  
Author(s):  
Marek Dzida ◽  
Krzysztof Kosowski
Keyword(s):  
Pressure Drop ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Relative Pressure ◽  
Wide Range ◽  
Few Data

In bibliography we can find many methods of determining pressure drop in the combustion chambers of gas turbines, but there is only very few data of experimental results. This article presents the experimental investigations of pressure drop in the combustion chamber over a wide range of part-load performances (from minimal power up to take-off power). Our research was carried out on an aircraft gas turbine of small output. The experimental results have proved that relative pressure drop changes with respect to fuel flow over the whole range of operating conditions. The results were then compared with theoretical methods.

Analysis of Indirectly Fired Gas Turbine Power Systems

2007 ◽  
Author(s):  
J. E. Donald Gauthier
Keyword(s):  
Power Generation ◽  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Turbine Engine ◽  
Engine Design ◽  
Wide Range ◽  
System Configurations

This paper describes the results of modelling the performance of several indirectly fired gas turbine (IFGT) power generation system configurations based on four gas turbine class sizes, namely 5 kW, 50 kW, 5 MW and 100 MW. These class sizes were selected to cover a wide range of installations in residential, commercial, industrial and large utility power generation installations. Because the IFGT configurations modelled consist of a gas turbine engine, one or two recuperators and a furnace; for comparison purpose this study also included simulations of simple cycle and recuperated gas turbine engines. Part-load, synchronous-speed simulations were carried out with generic compressor and turbine maps scaled for each engine design point conditions. The turbine inlet temperature (TIT) was varied from the design specification to a practical value for a metallic high-temperature heat exchanger in an IFGT system. As expected, the results showed that the reduced TIT can have dramatic impact on the power output and thermal efficiency when compared to that in conventional gas turbines. However, the simulations also indicated that several configurations can lead to higher performance, even with the reduced TIT. Although the focus of the study is on evaluation of thermodynamic performance, the implications of varying configurations on cost and durability are also discussed.

Sign in / Sign up

Export Citation Format

Share Document