Experimental Rotordynamic Coefficient Results for: (a) A Labyrinth Seal With and Without Shunt Injection and (b) A Honeycomb Seal

1998 ◽  
Author(s):  
Elias A. Soto A. ◽  
Dara W. Childs
Keyword(s):  
Pressure Ratio ◽  
Injection Pressure ◽  
Labyrinth Seal ◽  
Surface Velocity ◽  
Labyrinth Seals ◽  
Honeycomb Seal ◽  
Radial Injection ◽  
Rotor Surface ◽  
Rotordynamic Coefficient ◽  
Better Than

Centrifugal compressors are increasingly required to operate at higher pressures, speeds, and fluid density. In these conditions, compressors are susceptible to rotordynamic instabilities. To remedy this situation, labyrinth seals have sometimes been modified by using shunt injection. In shunt injection, the gas is taken from the diffuser or discharge volute and injected into an upstream chamber of the balance-piston labyrinth seal. The injection direction can be radial or against rotation. This study contains the first measured rotordynamic data for labyrinth seals with shunt injection. A comparison has been made between conventional labyrinth seals, labyrinth seal with shunt injection (radial and against rotation), and a honeycomb seal. Labyrinth seals with injection against rotation are better able to control rotordynamic instabilities than labyrinth seals with radial injection; however, the leakage is slightly higher. The leakage comparison for all seals demonstrates that the honeycomb seal has the best flow control. Test data are presented for a top rotor surface velocity of 110 m/sec, a supply pressure of 13.7 bars, and IPr = 0.95 (injection pressure is 1.05 = 1/0.95 times the seal inlet pressure). For these conditions, and considering effective damping, the labyrinth seal with injection against rotation is better than the honeycomb seal when the pressure ratio across the seal PR<0.45. On the other hand, the honeycomb seal is better when PR>0.45. The effectiveness of the shunt-injection against rotation in developing effective damping is reduced with increasing rotor surface velocity.

Experimental Rotordynamic Coefficient Results for (a) a Labyrinth Seal With and Without Shunt Injection and (b) a Honeycomb Seal

1999 ◽  
Vol 121 (1) ◽  
pp. 153-159 ◽  
Author(s):  
E. A. Soto ◽  
D. W. Childs
Keyword(s):  
Pressure Ratio ◽  
Injection Pressure ◽  
Labyrinth Seal ◽  
Surface Velocity ◽  
Labyrinth Seals ◽  
Honeycomb Seal ◽  
Radial Injection ◽  
Rotor Surface ◽  
Rotordynamic Coefficient ◽  
Better Than

Centrifugal compressors are increasingly required to operate at higher pressures, speeds, and fluid density. In these conditions, compressors are susceptible to rotordynamic instabilities. To remedy this situation, labyrinth seals have sometimes been modified by using shunt injection. In shunt injection, the gas is taken from the diffuser or discharge volute and injected into an upstream chamber of the balance-piston labyrinth seal. The injection direction can be radial or against rotation. This study contains the first measured rotordynamic data for labyrinth seals with shunt injection. A comparison has been made between conventional labyrinth seals, labyrinth seals with shunt injection (radial and against rotation), and a honeycomb seal. Labyrinth seals with injection against rotation are better able to control rotordynamic instabilities than labyrinth seals with radial injection; however, the leakage is slightly higher. The leakage comparison for all seals demonstrates that the honeycomb seal has the best flow control. Test data are presented for a top rotor surface velocity of 110 m/sec, a supply pressure of 13.7 bars, and IPr = 0.95 (injection pressure is 1.05 = 1/0.95 times the seal inlet pressure). For these conditions, and considering effective damping, the labyrinth seal with injection against rotation is better than the honeycomb seal when the pressure ratio across the seal PR < 0.45. On the other hand, the honeycomb seal is better when PR > 0.45. The effectiveness of the shunt-injection against rotation in developing effective damping is reduced with increasing rotor surface velocity.

Impact of Frequency Dependence of Gas Labyrinth Seal Rotordynamic Coefficients on Centrifugal Compressor Stability

2010 ◽  
Author(s):  
Giuseppe Vannini ◽  
Manish R. Thorat ◽  
Dara W. Childs ◽  
Mirko Libraschi
Keyword(s):  
Molecular Weight ◽  
Numerical Model ◽  
Control Volume ◽  
Labyrinth Seal ◽  
Labyrinth Seals ◽  
Frequency Dependent ◽  
Rotordynamic Coefficients ◽  
Frequency Independent ◽  
Rotor Surface ◽  
Independent Model

A numerical model developed by Thorat & Childs [1] has indicated that the conventional frequency independent model for labyrinth seals is invalid for rotor surface velocities reaching a significant fraction of Mach 1. A theoretical one-control-volume (1CV) model based on a leakage equation that yields a reasonably good comparison with experimental results is considered in the present analysis. The numerical model yields frequency-dependent rotordynamic coefficients for the seal. Three real centrifugal compressors are analyzed to compare stability predictions with and without frequency-dependent labyrinth seal model. Three different compressor services are selected to have a comprehensive scenario in terms of pressure and molecular weight (MW). The molecular weight is very important for Mach number calculation and consequently for the frequency dependent nature of the coefficients. A hydrogen recycle application with MW around 8, a natural gas application with MW around 18, and finally a propane application with molecular weight around 44 are selected for this comparison. Useful indications on the applicability range of frequency dependent coefficients are given.

scholarly journals Annular Honeycomb Seals: Test Results for Leakage and Rotordynamic Coefficients; Comparisons to Labyrinth and Smooth Configurations

1989 ◽  
Vol 111 (2) ◽  
pp. 293-300 ◽  
Author(s):  
D. Childs ◽  
D. Elrod ◽  
K. Hale
Keyword(s):  
Labyrinth Seal ◽  
Test Results ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Shaft Rotation ◽  
Honeycomb Seal ◽  
Cell Dimensions ◽  
Honeycomb Seals ◽  
Rotordynamic Coefficient

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals shows the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluids entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

Leakage and Cavity Pressures in an Interlocking Labyrinth Gas Seal: Measurements vs. Predictions

2019 ◽  
Author(s):  
Luis San Andrés ◽  
Tingcheng Wu ◽  
Jose Barajas-Rivera ◽  
Jiaxin Zhang ◽  
Rimpei Kawashita
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Inlet Pressure ◽  
Steam Turbines ◽  
Rotor Speed ◽  
Labyrinth Seals ◽  
Gas Seals

Abstract Gas labyrinth seals (LS) restrict secondary flows (leakage) in turbomachinery and their impact on the efficiency and rotordynamic stability of high-pressure compressors and steam turbines can hardly be overstated. Amongst seal types, the interlocking labyrinth seal (ILS), having teeth on both the rotor and on the stator, is able to reduce leakage up to 30% compared to other LSs with either all teeth on the rotor or all teeth on the stator. This paper introduces a revamped facility to test gas seals for their rotordynamic performance and presents measurements of the leakage and cavity pressures in a five teeth ILS. The seal with overall length/diameter L/D = 0.3 and small tip clearance Cr/D = 0.00133 is supplied with air at T = 298 K and increasing inlet pressure Pin = 0.3 MPa ∼ 1.3 MPa, while the exit pressure/inlet pressure ratio PR = Pout/Pin is set to range from 0.3 to 0.8. The rotor speed varies from null to 10 krpm (79 m/s max. surface speed). During the tests, instrumentation records the seal mass flow (ṁ) and static pressure in each cavity. In parallel, a bulk-flow model (BFM) and a computational fluid dynamics (CFD) analysis predict the flow field and deliver the same performance characteristics, namely leakage and cavity pressures. Both measurements and predictions agree closely (within 5%) and demonstrate the seal mass flow rate is independent of rotor speed. A modified flow factor Φ¯=m.T/PinD1-PR2 characterizes best the seal mass flow with a unique magnitude for all pressure conditions, Pin and PR.

scholarly journals Rotordynamic Coefficient and Leakage Test Results for Interlock and Tooth-on-Stator Labyrinth Seals

1988 ◽  
Author(s):  
Dara W. Childs ◽  
David A. Elrod ◽  
Keith Hale
Keyword(s):  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Leakage Test ◽  
Stiffness And Damping ◽  
Rotordynamic Coefficient

Test results (leakage and rotordynamic coefficients) are presented for an interlock and tooth-on-stator labyrinth seals. Tests were carried out with air at speeds out to 16,000 cpm and supply pressures up to 7.5 bars. The rotordynamic coefficients consist of direct and cross-coupled stiffness and damping coefficients. Damping-coefficient data have not previously been presented for interlock seals. The test results support the following conclusions: (a) The interlock seal leaks substantially less than labyrinth seals. (b) Destabilizing forces are lower for the interlock seal. (c) The labyrinth seal has substantially greater direct damping values than the interlock seal. A complete rotordynamics analysis is needed to determine which type of seal would yield the best stability predictions for a given turbomachinery unit.

Numerical Analysis of Honeycomb Labyrinth Seals: Cell Geometry and Fin Tip Thickness Impact on the Discharge Coefficient

2015 ◽  
Author(s):  
Alessio Desando ◽  
Andrea Rapisarda ◽  
Elena Campagnoli ◽  
Roberto Taurino
Keyword(s):  
Discharge Coefficient ◽  
New Technologies ◽  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Pollutant Emissions ◽  
Cell Diameter ◽  
Labyrinth Seals ◽  
Cell Pattern ◽  
Divergent Flow ◽  
Impact Reduction

The design of the newest aircraft propulsion systems is focused on environmental impact reduction. Extensive research is being carried out with the purpose of improving engine efficiency, enhancing crucial features, in order to decrease both fuel consumption and pollutant emissions. A lot of improvements to fulfill these objectives must be made, focusing on the optimization of the main engine parts through the utilization of new technologies. The leakage flow reduction in the turbo machinery rotor-stator interaction is one of the main topics to which numerous efforts are being devoted. Labyrinth seals, widely employed in the aerospace field thanks to their simple assembly process and maintenance, can be the means to achieve these objectives. This paper mainly focuses on the optimization of the labyrinth seal stator part, characterized, in modern Low Pressure Turbines (LPT), by a honeycomb cell pattern. The first phase of this study deals with the implementation and validation of a Computational Fluid Dynamics (CFD) numerical model, by using the experimental data available in the literature. Discharge coefficients obtained by numerical simulations, performed at different clearances and pressure ratios on both smooth and honeycomb non-rotating labyrinth seals, are presented and compared to the literature data. Then, for both convergent and divergent flow conditions, the effects on the discharge coefficient due to variations in several cell pattern parameters (i.e. cell diameter, depth and wall thickness) and fin tip thickness are shown. For these analyses the values of clearance and pressure ratio are set at a constant value.

Numerical and Experimental Investigation on the Effect of Swirl Brakes on the Labyrinth Seals

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Dan Sun ◽  
Shuang Wang ◽  
Cheng-Wei Fei ◽  
Yan-Ting Ai ◽  
Ke-Ming Wang
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Impedance Method ◽  
Swirl Ratio ◽  
Labyrinth Seals ◽  
Rotating Speed ◽  
Simulation And Experiment ◽  
Computational Fluid Dynamics Cfd ◽  
Static Flow

Swirl brake influences the static and rotordynamic characteristics of labyrinth seal which are important in the prediction of turbomachine stability. To study the influence of the swirl brakes on improving seal stability, the effects of swirl brakes on the static and rotordynamic characteristics of labyrinth seals were investigated by the combination of numerical simulation and experiment. First, it was performed to the effects of swirl brake on the static flow characteristics of labyrinth seal with swirl ratio and pressure distribution based on computational fluid dynamics (CFD). And then a comparison between leakage predicted by the CFD model and measurement was presented to verify the accuracy of the simulation. Moreover, an experiment was implemented to analyze the rotordynamic characteristics of labyrinth seal using an improved impedance method based on an unbalanced synchronous excitation method on a rotor test rig. The influences of swirl brake density, length, inlet/outlet pressure ratio, and rotating speed were measured and discussed, respectively. The CFD numerical results show that the swirl brake effectively reduces the seal swirl ratio (∼60–75% less), circumferential pressure difference (∼25–85% less) so that the seal destabilizing forces decrease. With the increasing of the swirl vanes density and length, the seal leakage drops (∼8–20% less). The experimental rotordynamic characteristics results show that it is more obvious to reduce the cross-couple stiffness (∼50–300% less) and increase the direct damping (∼50–60% larger) with the increasing in the number and length of the swirl vanes, and thus the swirl brake improves the seal rotordynamic stability. The efforts of this paper provide a useful insight to clearly understand the effects of swirl brakes on the labyrinth seal static and rotordynamic characteristics, which is beneficial to improve the design of annular seals.

Leakage and Windage Heating in Stepped Labyrinth Seals

2019 ◽  
Author(s):  
Kali Charan Nayak ◽  
Nomesh P. Kandaswamy ◽  
Syed Faheemulla
Keyword(s):  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Vital Role ◽  
Step Height ◽  
Axial Position ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Geometric Factors ◽  
Pitch Ratio ◽  
Computational Fluid Dynamics Cfd

Abstract Stepped labyrinth seals are used in multiple locations in the gas turbine with the intent to reduced leakage compared to straight labyrinth seals. However the selection of geometric factors in stepped labyrinth seals is critical to allow lower leakage in its operating envelope. Particularly the step height and axial position during the running condition play a vital role. The influence of these factors on the leakage, swirl development and windage heating in stepped labyrinth seal has not been thoroughly investigated in the previously published work. This paper focuses to study above effects with numerical simulations in a smooth four-fin stepped labyrinth seal. Specifically, a 2D axi-symmetric computational fluid dynamics (CFD) model is developed utilizing commercial finite volume-based software incorporating the standard k-ε turbulence model. Using this model, a broad parametric study is conducted by varying step height, axial position of the knife from the step, radial clearance and pressure ratio for a four-teeth stepped labyrinth seal. It has been observed that the seal leakage reduces with increase in step height to pitch ratio up to 0.35 and with further increase it tails off. The axial position of the tooth has strong influence on the flow structure and swirl development in the seal pocket.

Effects of Pressure Ratio and Sealing Clearance on Leakage Flow Characteristics in the Rotating Honeycomb Labyrinth Seal

2007 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Guojun Li ◽  
Zhenping Feng
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Aerodynamic Efficiency ◽  
Flow Losses ◽  
Leakage Flow Rate ◽  
Swirl Velocity

Honeycomb stepped labyrinth seals in turbomachinery enhance aerodynamic efficiency by reducing leakage flow losses through the clearance between rotating and stationary components. The influence of pressure ratio and sealing clearance on the leakage flow characteristics in the honeycomb stepped labyrinth seal is numerically determined. The geometries investigated represent designs of the honeycomb labyrinth seal typical for modern turbomachinery. The leakage flow fields in the honeycomb and smooth stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT. Numerical simulations covered a range of pressure ratio and three sizes of sealing clearance for the honeycomb and smooth stepped labyrinth seals. The numerical discharge coefficients of the non-rotating honeycomb and smooth stepped labyrinth seals are in good agreement with previous experimental data. In addition rotational effects are also taken into account in numerical computations. The numerical results show that the leakage flow rate increases with the increasing pressure ratio at the fixed sealing clearance for the rotating and non-rotating honeycomb labyrinth seal. The influence of the sealing clearance on the leakage flow pattern for the rotating and non-rotating honeycomb labyrinth seal are observed. Moreover, the similar leakage flow rates are obtained at the same flow condition between the rotating and non-rotating honeycomb labyrinth seal due to the honeycomb acts to kill swirl velocity development for the rotating honeycomb labyrinth seal.

Influence of Honeycomb Land Geometry on Seal Performance

2016 ◽  
Author(s):  
Daniel Frączek ◽  
Krzysztof Bochon ◽  
Włodzimierz Wróblewski
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Labyrinth Seal ◽  
Qualitative Assessment ◽  
Labyrinth Seals ◽  
Leakage Flows ◽  
Ansys Cfx ◽  
Cell Shapes ◽  
Geometrical Data ◽  
Three Dimensional Models

The aim of this study was to identify the best structures of the honeycomb (or structures used instead of it) that can be applied to a seal cavity labyrinth in order to improve the sealing performance. The problem was investigated numerically using the ANSYS CFX commercial software. The paper presents geometrical data concerning the proposed solutions to the labyrinth seal land structure. A simple straight-through labyrinth geometry with two leaned fins is analysed. Such a simple structure of the flow conditions was chosen to reduce the influence of other effects on the seal performance. Three-dimensional models of the labyrinth seal were elaborated for each honeycomb or honeycomb-like land structure. The following concepts were analysed: an inclination of the honeycomb cells, a land with different cell shapes (squeezed honeycomb) and honeycomb cells filled with a porous material. The labyrinth seals with different land structures were compared with two reference cases: a seal with a standard honeycomb land (with 1/8-inch cell size) and a seal with a smooth land. Calculations were performed for the pressure ratio values ranging from 1.08 to 1.8 and for varied sizes of the clearance. Main parameters of the leakage flows are discussed. Additionally, the influence of the inlet narrowing on the seal performance is investigated. A qualitative assessment of the seal concepts is made and the most promising solutions are pointed out.

Sign in / Sign up

Export Citation Format

Share Document