Conjugate Heat Transfer Analysis for Film Cooling Configurations With Different Hole Geometries

2003 ◽  
Author(s):  
Dieter Bohn ◽  
Jing Ren ◽  
Karsten Kusterer
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Secondary Flows ◽  
Heat Transfer Analysis ◽  
Transfer Condition ◽  
Film Cooling Effectiveness

Secondary flows in the cooling jets are the main reason for the degradation of the cooling performance of a film-cooled blade. The formation of kidney vortices can significantly be reduced for shaped holes instead of cylindrical holes. For the determination of the film cooling heat transfer, the design of a turbine blade relies on the conventional determination of the adiabatic film cooling effectiveness and heat transfer conditions for test configurations. Thus, additional influences by the interaction of fluid flow and heat transfer and influences by additional convective heat transfer cannot be taken into account with sufficient accuracy. Within this paper, calculations of a film-cooled duct wall with application of the adiabatic and a conjugate heat transfer condition have been performed for different configurations with cylindrical and shaped holes. It can be shown that the application of the conjugate calculation method comprises the influence of heat transfer on the velocity field within the cooling film. In particular, the secondary flow velocities are affected by the local heat transfer, which varies significantly depending on the local position.

scholarly journals Systematic Investigation on Conjugate Heat Transfer Rates of Film Cooling Configurations

2005 ◽  
Vol 2005 (3) ◽  
pp. 211-220 ◽  
Author(s):  
Dieter Bohn ◽  
Jing Ren ◽  
Karsten Kusterer
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Systematic Investigation ◽  
Transfer Condition ◽  
Film Cooling Effectiveness ◽  
Conjugate Calculation

For the determination of the film-cooling heat transfer, the design of a turbine blade relies on the conventional determination of the adiabatic film-cooling effectiveness and heat transfer conditions for test configurations. Thus, additional influences by the interaction of fluid flow and heat transfer and influences by additional convective heat transfer cannot be taken into account with sufficient accuracy. Within this paper, calculations of a film-cooled duct wall and a film-cooled real blade with application of the adiabatic and a conjugate heat transfer condition have been performed for different configurations. It can be shown that the application of the conjugate calculation method comprises the influence of heat transfer within the cooling film. The local heat transfer rate varies significantly depending on the local position.

Conjugate Heat Transfer Analysis to Assess Overall Cooling Effectiveness of High Pressure Turbine Nozzle With Optimized Film Cooling Hole Arrangements

2019 ◽  
Author(s):  
Young Seok Kang ◽  
Dong-Ho Rhee ◽  
Sanga Lee ◽  
Bong Jun Cha
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Analysis ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Baseline Design ◽  
Pressure Surface

Abstract Conjugate heat transfer analysis method has been highlighted for predicting heat exchange between fluid domain and solid domain inside high-pressure turbines, which are exposed to very harsh operating conditions. Then it is able to assess the overall cooling effectiveness considering both internal cooling and external film cooling at the cooled turbine design step. In this study, high-pressure turbine nozzles, which have three different film cooling holes arrangements, were numerically simulated with conjugate heat transfer analysis method for predicting overall cooling effectiveness. The film cooling holes distributed over the nozzle pressure surface were optimized by minimizing the peak temperature, temperature deviation. Additional internal cooling components such as pedestals and rectangular rib turbulators were modeled inside the cooling passages for more efficient heat transfer. The real engine conditions were given for boundary conditions to fluid and solid domains for conjugate heat transfer analysis. Hot combustion gas properties such as specific heat at constant pressure and other transport properties were given as functions of temperature. Also, the conductivity of Inconel 718 was also given as a function of temperature to solve the heat equation in the nozzle solid domain. Conjugate heat transfer analysis results showed that optimized designs showed better cooling performance, especially on the pressure surface due to proper staggering and spacing hole-rows compared to the baseline design. The overall cooling performances were offset from the adiabatic film cooling effectiveness. Locally concentrated heat transfer and corresponding high cooling effectiveness region appeared where internal cooling effects were overlapped in the optimized designs. Also, conjugate heat transfer analysis results for the optimized designs showed more uniform contours of the overall cooling effectiveness compared to the baseline design. By varying the coolant mass flow rate, it was observed that pressure surface was more sensitive to the coolant mass flow rate than nozzle leading edge stagnation region and suction surface. The CHT results showed that optimized designs to improve the adiabatic film cooling effectiveness also have better overall cooling effectiveness.

Film Cooling on Highly Loaded Blades With Main Flow Separation—Part I: Heat Transfer

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Film cooling experiments were run at the high speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out with a linear cascade of highly loaded turbine blades. The main objectives of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. Therefore, the blades were designed to force the flow to detach on the pressure side shortly downstream of the leading edge and reattach at about half of the axial chord. In this zone, film cooling rows are placed among others for a reduction of the size of the separation bubble. The analyzed region on the blade is critical due to the high heat transfer present at the leading edge and at the reattachment line after the main flow separation. Film cooling can contribute to a reduction of the size of the separation bubble reducing aerodynamic losses, however, in general, it increases heat transfer due to turbulent mixing. The reduction of the size of the separation bubble might also be twofold, since it acts like a thermal insulator on the blade and reducing the size of the bubble might lead to a stronger heating of the blade. Film cooling should, therefore, take both into account: first, a proper protection of the surface and second, reducing aerodynamic losses, diminishing the extension of the main flow separation. While experimental results of the adiabatic film cooling effectiveness were shown in previous publications, the local heat transfer is analyzed in this paper. Emphasis is also placed upon analyzing, in detail, the flow separation process. Furthermore, the tests comprise the analysis of the effect of different outlet Mach and Reynolds numbers and film cooling. In part two of this paper, the overall film cooling effectiveness is addressed. Local heat transfer is still difficult to predict with modern numerical tools and this is especially true for complex flows with flow separation. Some numerical results with the Reynolds averaged Navier-Stokes (RANS) and large eddy simulation (LES) show the capability of a commercial solver in predicting the heat transfer.

Effect of Surface Roughness on Local Heat Transfer and Film Cooling Effectiveness

1995 ◽  
Author(s):  
Douglas N. Barlow ◽  
Yong W. Kim
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Smooth Surface ◽  
Rough Surfaces ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients

An experimental investigation of film cooling on rough surfaces has been accomplished at a Reynolds number and dimensionless boundary layer momentum thickness found in current high performance first stage turbine vanes. A transient experimental method using thermochromic liquid crystals is employed to determine both local heat transfer coefficients and film cooling effectiveness values on planar rough surfaces. Two surface roughness configurations are investigated with a single row of cooling holes spaced three diameters apart and inclined 30° to the mainstream flow. The mainstream turbulence level at the point of film injection is 8.5% and the density ratio considered is approximately 1.0. The influence of roughness on the centerline film cooling effectiveness, laterally averaged film cooling effectiveness, laterally averaged heat transfer coefficients, as well as area averaged values are presented. It is found that the presence of roughness causes a decrease in the film cooling effectiveness over that of the smooth surface for the range of experimental parameters considered in this study. In addition, significant lateral smoothing in film cooling effectiveness distribution is observed for the rougher surfaces. Measured heat transfer coefficients on rough surfaces show a trend of monotonic increase with blowing ratio. However, such increase is not as great as that for the case of smooth surface.

Film-Cooling Characteristics of Pressure-Side Discharge Slots in an Accelerating Mainstream Flow

2005 ◽  
Author(s):  
Yong W. Kim ◽  
Chad Coon ◽  
Hee-Koo Moon
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Mainstream Flow

Pressure-side discharge is commonly employed in turbine blades and nozzle guide vanes to keep the trailing edge metal temperatures within an allowable limit while minimizing aerodynamic penalties. Despite its widespread use, film-cooling data of the discharge slot are scarce in open literature. The objectives of the present experimental study were to measure detailed local heat transfer and film-cooling effectiveness from a 10x scale trailing-edge model of an industrial gas turbine airfoil in a low speed wind tunnel. To simulate the mainstream flow acceleration in vane and blade row passages, a linear velocity gradient was imposed using an adjustable top wall. The present work employed the composite slab quasi-steady liquid crystal method that allows measurements of local heat transfer coefficients and film-cooling effectiveness from two related tests. With this technique, the heat transfer measurement can be performed in a cold wind tunnel. The coolant-to-mainstream blowing ratio was varied between 0.25 and 1.0. The slot hydraulic diameter based Reynolds number ranged from 4,760 to 19,550. The coolant-to-mainstream density ratio was fixed at 0.95. Slot discharge coefficients were also measured with mainstream acceleration. Both local heat transfer coefficients and film-cooling effectiveness displayed a strong dependency on blowing ratio and mainstream acceleration. However, the discharge coefficients showed little dependency on the mainstream acceleration.

Film Cooling on Highly Loaded Blades With Main Flow Separation—Part II: Overall Film Cooling Effectiveness

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Film cooling experiments were run at the high speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out with a linear cascade of highly loaded turbine blades. The main targets of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. Therefore the blades were designed to force the flow to detach on the pressure side shortly downstream of the leading edge and it reattaches at about half of the axial chord. In this zone, film cooling rows are placed among others for reduction of the size of the separation bubble. The analyzed region on the blade is critical due to the high heat transfer present at the leading edge and at the reattachment line after main flow separation. Film cooling can contribute to a reduction of the size of the separation bubble reducing aerodynamic losses but increases in general heat transfer due to turbulent mixing. The reduction of the size of the separation bubble might also be two-fold since it acts like a thermal insulator on the blade and reducing the size of the bubble might lead to stronger heating of the blade. Film cooling should therefore take into account both: firstly, a proper protection of the surface, and secondly, reduce aerodynamic losses diminishing the extension of the main flow separation. The overall effectiveness of film cooling for a real engine has to combine heat transfer with film cooling effect. In this paper, the overall effectiveness of film cooling, combining results from measurements of the adiabatic film cooling effectiveness and the local heat transfer coefficient are shown. The tests comprise the analysis of the effect of different outlet Mach and Reynolds numbers at engine relevant values and film cooling ratio. A new parameter is introduced which allows for the evaluation of the effect of film cooling accounting at the same time for the change of local heat transfer coefficient. To the authors’ opinion this parameter allows a better, physically based assessment than the strategy using the so-called heat flux ratio. A parameter study is carried out in order to benchmark the effect of changes of the blade design.

scholarly journals Conjugate Heat Transfer Analysis of Flat Plate Subjected to Impingement and Film Cooling

2021 ◽  
Vol 9 (9) ◽  
pp. 1667-1678
Author(s):  
Devaraj K
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flat Plate ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Jet Impingement ◽  
Heat Transfer Analysis ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Abstract: The present computational study involves a flat plate subjected to combined effect of jet impingement and film cooling. A conjugate heat transfer model in conjunction with k-ω SST turbulence model is employed to study the turbulence effects. The effect of Reynolds number varying from 389 to 2140 on static temperature, Nusselt number and film cooling effectiveness has be discussed for the blowing ratios of 0.6, 0.8, 1.0. The variation in the size of vortices formed on the impinging surface with Reynolds number is studied. It has been observed that the local Nusselt number shows a rising trend with the increase in Reynolds number, while the static temperatures follow the downfall in its values. As a result, an enhancement in the effectiveness is observed, which is credited to the capabilities of combined impingement and film cooling. At Reynolds number of 972, the coolant jet is found to be attached to the surface, for this condition the heat transfer phenomena for blowing ratios of 0.6, 0.8, 1.0, 1.2, 1.6, 2.0, 2.4, 2.6 are studied to understand the flow distribution on the plate surface. Keywords: Jet impingement, film cooling, effectiveness, conjugate heat transfer

Turbulence and Heat Transfer Measurements in an Inclined Large Scale Film Cooling Array: Part II—Temperature and Heat Transfer Measurements

2011 ◽  
Author(s):  
Douglas R. Thurman ◽  
Lamyaa A. El-Gabry ◽  
Philip E. Poinsatte ◽  
James D. Heidmann
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Large Scale ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Surface Heat ◽  
Transfer Coefficients ◽  
Film Cooling Effectiveness ◽  
Surface Heat Transfer ◽  
Film Cooling Holes

The second of a two-part paper, this study focuses on the temperature field and surface heat transfer measurements on a large-scale models of an inclined row of film cooling holes. Detailed surface and flow field measurements were taken and presented in Part I. The model consists of three holes of 1.9-cm diameter that are spaced 3 hole diameters apart and inclined 30° from the surface. Additionally, another model with an anti-vortex adaptation to the film cooling holes is also tested. The coolant stream is metered and cooled to 20°C below the mainstream temperature. A thermocouple is used to obtain the flow temperatures along the jet centerline and at various streamwise locations. Steady state liquid crystal thermography is used to obtain surface heat transfer coefficients. Results are obtained for blowing ratios of up to 2 in order to capture off-design conditions in which the jet is lifted. Film cooling effectiveness values of 0.4 and 0.15 were found along the centerline for blowing ratios of 1 and 2 respectively. In addition, an anti-vortex design was tested and found to have improved film effectiveness. This paper presents the detailed temperature contours showing the extent of mixing between the coolant and freestream and the local heat transfer results.

Conjugate Heat Transfer Analysis of Turbine Rotor-Stator System

2002 ◽  
Author(s):  
Yoji Okita ◽  
Shigemichi Yamawaki
Keyword(s):  
Heat Transfer ◽  
Conjugate Heat Transfer ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Turbine Rotor ◽  
Heat Transfer Analysis ◽  
Disk System ◽  
Computational Resources ◽  
Good Agreement

A fluid-solid conjugate solver has been newly developed and applied to an actual engine disk system. Most of the currently available conjugate solvers lack the special thermal modeling for turbomachinery disk system applications. In the present new code, these special models are implemented to expand the applicability of the conjugate method and to reduce the required computational resources. Most of the conjugate analysis work so far were limited to the axisymmetric framework. However, the actual disk system includes several non-axisymmetric components which inevitably affect the local heat transfer phenomena. This paper presents 3D conjugate analysis of a single stage high pressure turbine rotor-stator disk system to assess these three-dimensional effects. The predicted temperatures shows good agreement with measured data. The calculated results revealed the three-dimensional analysis is crucial to predict the correct heat transfer field which is especially important in transient situations.

Film Cooling on Highly Loaded Blades With Main Flow Separation: Part 1—Heat Transfer

2011 ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Film cooling experiments were run at the high speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out with a linear cascade of highly loaded turbine blades. The main targets of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. Therefore the blades were designed to force the flow to detach on the pressure side shortly downstream of the leading edge and it reattaches at about half of the axial chord. In this zone film cooling rows are placed among others for reduction of the size of the separation bubble. The analyzed region on the blade is critical due to the high heat transfer present at the leading edge and at the reattachment line after main flow separation. Film cooling can contribute to a reduction of the size of the separation bubble reducing aerodynamic losses but increases in general heat transfer due to turbulent mixing. The reduction of the size of the separation bubble might also be twofold since it acts like a thermal insulator on the blade and reducing the size of the bubble might lead to stronger heating of the blade. Film cooling should therefore take into account both: firstly a proper protection of the surface and secondly reduce aerodynamic losses diminishing the extension of the main flow separation. While experimental results of the adiabatic film cooling effectiveness were shown in previous publications, the local heat transfer is analyzed in this paper. Emphasis is also put in analyzing in detail the flow separation process. The tests comprise furthermore the analysis of the effect of different outlet Mach and Reynolds numbers and film cooling. In part two of this paper the overall film cooling effectiveness is addressed. Local heat transfer is still difficult to predict with modern numerical tools and this is especially true for complex flows with flow separation. Some numerical results with RANS and LES show the capability of a commercial solver in predicting the heat transfer.

Sign in / Sign up

Export Citation Format

Share Document