Dynamic Analysis and Sliding Mode Impedance Control of a Robot Manipulator Subject to Impact/Contact With an Arbitrary Environment

2010 ◽  
Author(s):  
Masih Mahmoodi ◽  
Mehrdad Farid ◽  
Mohammad Eghtesad
Keyword(s):  
Abrupt Change ◽  
Sliding Mode ◽  
Robot Manipulator ◽  
Impedance Control ◽  
Contact Dynamics ◽  
Simulation Studies ◽  
Environment Impact ◽  
Contact Phenomenon ◽  
Simulation Results ◽  
Contact Impact

In this paper, dynamic equations of a robot manipulator subject to compliant contact/impact with the environment are derived using nonlinear elastodynamic approach. Then, a sliding mode impedance algorithm is proposed to control compliant impact/contact dynamics of the robot manipulator with an arbitrary environment. Impact/contact phenomenon can be regarded as a perturbation due to an abrupt change of system’s velocity. Thus the need to have robust characteristics in such systems especially after impact seems to be evident. The performance of the proposed controller is compared against standard second order impedance controller through numerical simulation studies. Finally, simulation results are provided to show the effectiveness of the proposed algorithm.

A Modular 2-DOF Serial Robot Manipulator for Education in Robot Control

2016 ◽  
Author(s):  
Stephen Mascaro
Keyword(s):  
Robot Control ◽  
Inverse Dynamics ◽  
Position Control ◽  
Sliding Mode ◽  
Feedforward Control ◽  
Robot Manipulator ◽  
Impedance Control ◽  
Force Sensor ◽  
Control Techniques ◽  
Serial Robot

This paper describes a modular 2-DOF serial robot manipulator and accompanying experiments that have been developed to introduce students to the fundamentals of robot control. The robot is designed to be safe and simple to use, and to have just enough complexity (in terms of nonlinear dynamics) that it can be used to showcase and compare the performance of a variety of textbook robot control techniques including computed torque feedforward control, inverse dynamics control, robust sliding-mode control, and adaptive control. These various motion control schemes can be easily implemented in joint space or operational space using a MATLAB/Simulink real-time interface. By adding a simple 2-DOF force sensor to the end-effector, the robot can also be used to showcase a variety of force control techniques including impedance control, admittance control, and hybrid force/position control. The 2-DOF robots can also be used in pairs to demonstrate control architectures for multi-arm coordination and master/slave teleoperation. This paper will describe the 2-DOF robot and control hardware/software, illustrate the spectrum of robot control methods that can be implemented, and show sample results from these experiments.

scholarly journals Robust Control for a Two DOF Robot Manipulator

2019 ◽  
Vol 2019 ◽  
pp. 1-11
Author(s):  
Fatma Massaoudi ◽  
Dorsaf Elleuch ◽  
Tarak Damak
Keyword(s):  
Robust Control ◽  
Sliding Mode Control ◽  
Sliding Mode ◽  
Robot Manipulator ◽  
Model Uncertainties ◽  
Robot System ◽  
Control Techniques ◽  
Simulation Results ◽  
Manipulator Robot

In this paper, we present robust control techniques applied on a manipulator robot system: modified sliding mode control (MSMC) and backstepping control (BSC). The purpose is to evaluate SMC and BSC performances, taking into account the model uncertainties. Then, the obtained results of MSMC technique are compared with those of the adaptive sliding mode. Both methods have comparable simulation results which show a good quality of robustness. However, simulation results prove that the modified SMC is more robust, mostly under the effect of external variations and uncertainties.

Sliding Mode Hybrid Impedance Control of Robot Manipulators Interacting With Unknown Environments Using VSMRC Method

2012 ◽  
Author(s):  
Aghil Jafari ◽  
Reza Monfaredi ◽  
Mehdi Rezaei ◽  
Ali Talebi ◽  
Saeed Shiry Ghidary
Keyword(s):  
Control System ◽  
Hybrid Control ◽  
Sliding Mode ◽  
Robot Manipulator ◽  
Impedance Control ◽  
Variable Structure ◽  
Structure Model ◽  
Robust Controller ◽  
Control Approach ◽  
Chattering Effect

In the present paper, the objective of hybrid impedance control is specified and a robust hybrid impedance control approach is proposed. Based on the concept of hybrid control, the task space is decomposed into position and force controlled subspaces. Impedance control is used in the position controlled subspace. Desired inertia and damping are applied in the force controlled subspace to meliorate the dynamic behavior of robot manipulator. Robust controller using the variable structure model reaching control (VSMRC) is introduced that can realize the objective impedance in the sliding mode in finite time. In order to overcome the chattering effect due to sliding mode approach, fuzzy logic methodology is employed in the control system. In addition, the reaching transient response is undertaken with prescribed quality. Simulating the control system for a 6DOF PUMA560 robot confirms the validity and effectiveness of the proposed control system.

Impedance Control Based Sliding Mode for Lower Limb Rehabilitation Robot

2014 ◽  
Vol 672-674 ◽  
pp. 1770-1773 ◽  
Author(s):  
Fu Cheng Cao ◽  
Li Min Du
Keyword(s):  
Dynamic Response ◽  
Sliding Mode Control ◽  
Lower Limb ◽  
Control Method ◽  
Sliding Mode ◽  
Impedance Control ◽  
Rehabilitation Robot ◽  
Active Rehabilitation ◽  
Limb Rehabilitation ◽  
Lower Limb Rehabilitation

Aimed at improving the dynamic response of the lower limb for patients, an impedance control method based on sliding mode was presented to implement an active rehabilitation. Impedance control can achieve a target-reaching training without the help of a therapist and sliding mode control has a robustness to system uncertainty and vary limb strength. Simulations demonstrate the efficacy of the proposed method for lower limb rehabilitation.

scholarly journals Optimization of sliding mode control with PID surface for robot manipulator by Evolutionary Algorithms

2020 ◽  
Vol 10 (1) ◽  
pp. 396-407
Author(s):  
Fatiha Loucif ◽  
Sihem Kechida
Keyword(s):  
Sliding Mode ◽  
Robot Manipulator ◽  
Absolute Error ◽  
Grey Wolf Optimizer ◽  
Optimal Parameters ◽  
Error Criterion ◽  
Trajectory Tracking Control ◽  
Integral Time ◽  
Sine Cosine Algorithm ◽  
Antlion Optimization

AbstractIn this paper, a sliding mode controller (SMC) with PID surface is designed for the trajectory tracking control of a robot manipulator using different optimization algorithms such as, Antlion Optimization Algorithm (ALO) Sine Cosine Algorithm (SCA) Grey Wolf Optimizer (GWO) and Whale Optimizer Algorithm (WOA). The aim of this work is to introduce a novel SMC-PID-ALO to control nonlinear systems, especially the position of two of the joints of a 2DOF robot manipulator. The basic idea is to determinate four optimal parameters (Kp, Ki, Kd and lamda) ensuring the best performance of a robot manipulator system, minimizing the integral time absolute error criterion (ITAE) and the integral time square error criterion (ISTE). The robot manipulator is modeled in Simulink and the control is implemented using the MATLAB environment. The obtained simulation results prove the robustness of ALO in comparison with other algorithms.

Speed regulation control of tractors’ new dual-flow transmission system based on slip rate resistance classification

2021 ◽  
pp. 095440702110105
Author(s):  
Guang Xia ◽  
Yan Xia ◽  
Xiwen Tang ◽  
Linfeng Zhao ◽  
Baoqun Sun
Keyword(s):  
Control Strategy ◽  
Control Algorithm ◽  
Production Efficiency ◽  
Sliding Mode ◽  
Slip Rate ◽  
Speed Control ◽  
Working Environment ◽  
Vehicle Speed ◽  
Speed Change ◽  
Simulation Results

Fluctuations in operation resistance during the operating process lead to reduced efficiency in tractor production. To address this problem, the project team independently developed and designed a new type of hydraulic mechanical continuously variable transmission (HMCVT). Based on introducing the mechanical structure and transmission principle of the HMCVT system, the priority of slip rate control and vehicle speed control is determined by classifying the slip rate. In the process of vehicle speed control, the driving mode of HMCVT system suitable for the current resistance state is determined by classifying the operation resistance. The speed change rule under HMT and HST modes is formulated with the goal of the highest production efficiency, and the displacement ratio adjustment surfaces under HMT and HST modes are determined. A sliding mode control algorithm based on feedforward compensation is proposed to address the problem that the oil pressure fluctuation has influences on the adjustment accuracy of hydraulic pump displacement. The simulation results of Simulink show that this algorithm can not only accurately follow the expected signal changes, but has better tracking stability than traditional PID control algorithm. The HMCVT system and speed control strategy models were built, and simulation results show that the speed control strategy can restrict the slip rate of driving wheels within the allowable range when load or road conditions change. When the tractor speed is lower than the lower limit of the high-efficiency speed range, the speed change law formulated in this paper can improve the tractor speed faster than the traditional rule, and effectively ensure the production efficiency. The research results are of great significance for improving tractor’s adaptability to complex and changeable working environment and promoting agricultural production efficiency.

Comprehensive Analysis for Influence of Controllable Damper Time Delay on Semi-Active Suspension Control Strategies

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Yechen Qin ◽  
Feng Zhao ◽  
Zhenfeng Wang ◽  
Liang Gu ◽  
Mingming Dong
Keyword(s):  
Time Delay ◽  
Dynamic Characteristics ◽  
Ride Comfort ◽  
Hybrid Control ◽  
Sliding Mode ◽  
Control Strategies ◽  
Active Suspension ◽  
Test System ◽  
Suspension Control ◽  
Simulation Results

This paper presents a comprehensive comparison and analysis for the effect of time delay on the five most representative semi-active suspension control strategies, and refers to four unsolved problems related to semi-active suspension performance and delay mechanism that existed. Dynamic characteristics of a commercially available continuous damping control (CDC) damper were first studied, and a material test system (MTS) load frame was used to depict the velocity-force map for a CDC damper. Both inverse and boundary models were developed to determine dynamic characteristics of the damper. In addition, in order for an improper damper delay of the form t+τ to be corrected, a delay mechanism of controllable damper was discussed in detail. Numerical simulation for five control strategies, i.e., modified skyhook control SC, hybrid control (HC), COC, model reference sliding mode control (MRSMC), and integrated error neuro control (IENC), with three different time delays: 5 ms, 10 ms, and 15 ms was performed. Simulation results displayed that by changing control weights/variables, performance of all five control strategies varied from being ride comfort oriented to being road handling oriented. Furthermore, increase in delay time resulted in deterioration of both ride comfort and road handling. Specifically, ride comfort was affected more than road handling. The answers to all four questions were finally provided according to simulation results.

scholarly journals Software Sensor to Enhance Online Parametric Identification for Nonlinear Closed-Loop Systems for Robotic Applications

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3653
Author(s):  
Lilia Sidhom ◽  
Ines Chihi ◽  
Ernest Nlandu Kamavuako
Keyword(s):  
Degrees Of Freedom ◽  
Closed Loop ◽  
Sliding Mode ◽  
Robot Manipulator ◽  
Parametric Identification ◽  
Recursive Least Squares ◽  
Unknown Parameters ◽  
Closed Loop Identification ◽  
Input Variables ◽  
Robotic Applications

This paper proposes an online direct closed-loop identification method based on a new dynamic sliding mode technique for robotic applications. The estimated parameters are obtained by minimizing the prediction error with respect to the vector of unknown parameters. The estimation step requires knowledge of the actual input and output of the system, as well as the successive estimate of the output derivatives. Therefore, a special robust differentiator based on higher-order sliding modes with a dynamic gain is defined. A proof of convergence is given for the robust differentiator. The dynamic parameters are estimated using the recursive least squares algorithm by the solution of a system model that is obtained from sampled positions along the closed-loop trajectory. An experimental validation is given for a 2 Degrees Of Freedom (2-DOF) robot manipulator, where direct and cross-validations are carried out. A comparative analysis is detailed to evaluate the algorithm’s effectiveness and reliability. Its performance is demonstrated by a better-quality torque prediction compared to other differentiators recently proposed in the literature. The experimental results highlight that the differentiator design strongly influences the online parametric identification and, thus, the prediction of system input variables.

scholarly journals Compliant Human–Robot Collaboration with Accurate Path-Tracking Ability for a Robot Manipulator

2021 ◽  
Vol 11 (13) ◽  
pp. 5914
Author(s):  
Daniel Reyes-Uquillas ◽  
Tesheng Hsiao
Keyword(s):  
Sliding Mode ◽  
Robot Manipulator ◽  
Industrial Robot ◽  
Path Following ◽  
Path Tracking ◽  
Control Loop ◽  
Loop Control ◽  
Tracking Ability ◽  
The Difference ◽  
Human Robot Collaboration

In this article, we aim to achieve manual guidance of a robot manipulator to perform tasks that require strict path following and would benefit from collaboration with a human to guide the motion. The robot can be used as a tool to increase the accuracy of a human operator while remaining compliant with the human instructions. We propose a dual-loop control structure where the outer admittance control loop allows the robot to be compliant along a path considering the projection of the external force to the tangential-normal-binormal (TNB) frame associated with the path. The inner motion control loop is designed based on a modified sliding mode control (SMC) law. We evaluate the system behavior to forces applied from different directions to the end-effector of a 6-DOF industrial robot in a linear motion test. Next, a second test using a 3D path as a tracking task is conducted, where we specify three interaction types: free motion (FM), force-applied motion (FAM), and combined motion with virtual forces (CVF). Results show that the difference of root mean square error (RMSE) among the cases is less than 0.1 mm, which proves the feasibility of applying this method for various path-tracking applications in compliant human–robot collaboration.

CONTROLLING THE UNCERTAIN MULTI-SCROLL CRITICAL CHAOTIC SYSTEM WITH INPUT NONLINEAR USING SLIDING MODE CONTROL

2009 ◽  
Vol 23 (16) ◽  
pp. 2021-2034 ◽  
Author(s):  
XINGYUAN WANG ◽  
DA LIN ◽  
ZHANJIE WANG
Keyword(s):  
Chaotic System ◽  
Sliding Mode ◽  
Equilibrium Points ◽  
Dead Zone ◽  
Variable Structure ◽  
Sliding Mode Controller ◽  
Global Stabilization ◽  
Structure Control ◽  
Control Scheme ◽  
Simulation Results

In this paper, control of the uncertain multi-scroll critical chaotic system is studied. According to variable structure control theory, we design the sliding mode controller of the uncertain multi-scroll critical chaotic system, which contains sector nonlinearity and dead zone inputs. For an arbitrarily given equilibrium point of the uncertain multi-scroll chaotic system, we achieve global stabilization for the equilibrium points. Particularly, a class of proportional integral (PI) switching surface is introduced for determining the convergence rate. Furthermore, the proposed control scheme can be extended to complex multi-scroll networks. Finally, simulation results are presented to demonstrate the effectiveness of the proposed control scheme.

Sign in / Sign up

Export Citation Format

Share Document