Detailed numerical simulation and experimental investigation on micromixers with serpentine Koch fractal microchannels

2021 ◽  
pp. 2150228
Author(s):  
Yue Tian ◽  
Xueye Chen ◽  
Xiangwei Zeng ◽  
Xiangyang Wang ◽  
Xingxing Yu ◽  
...  
Keyword(s):  
Cross Section ◽  
Molecular Diffusion ◽  
Continuous Optimization ◽  
Fluid Mixing ◽  
Mixing Efficiency ◽  
Channel Spacing ◽  
Section Shape ◽  
Passive Micromixer ◽  
Koch Fractal ◽  
Fractal Number

Micromixer is a kind of microfluidic chip for fast mixing and analysis. Mixing in a micromixer is usually a micron scale. At low Reynolds number, the fluid in the channel is laminar flow, which mainly depends on molecular diffusion as the main mixing mode. Fluid mixing in microchannels is very difficult, especially when the viscosity of the fluid is high. In this paper, we design a novel passive micromixer. The effects of fractal number, Koch fractal channel spacing, microchannel depth and cross-section shape on mixing efficiency were studied. Through a large number of numerical simulations, we continue to optimize the structure of the micromixer and improve the mixing efficiency. Finally, through the continuous optimization of the structure of the micromixer, the mixing efficiency of the micromixer can reach more than 95%.

Numerical simulation of three-dimensional passive micromixer based on the principle of Koch fractal

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Siyue Xiong ◽  
Xueye Chen
Keyword(s):  
Numerical Simulation ◽  
Fluid Flow ◽  
Cross Section ◽  
Three Dimensional ◽  
Mixing Efficiency ◽  
Mixing Performance ◽  
Chaotic Convection ◽  
Passive Micromixer ◽  
Koch Fractal ◽  
Koch Fractal Principle

Abstract In this paper, We arrange the obstacles based on the Koch fractal principle (OKF) in the micromixer. By changing the fluid flow and folding the fluid, a better mixing performance is achieved. We improve the mixing efficiency by placing OKF and changing the position of OKF, then we studied the influence of the number of OKF and the height of the micromixer on the mixing performance. The results show that when eight OKF are staggered in the microchannel and the height is 0.2 mm, the mixing efficiency of the OKF micromixer can reach 97.1%. Finally, we compared the velocity cross section and velocity streamline of the fluid, and analyzed the influence of OKF on the concentration trend. Through analysis, it is concluded that OKF can generate chaotic convection in the fluid, and enhance the mixing of fluids by generating vortices and folding the fluid. It can effectively improve the mixing efficiency of the micromixer.

scholarly journals Toward the Next Generation of Passive Micromixers: A Novel 3-D Design Approach

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 372
Author(s):  
Mahmut Burak Okuducu ◽  
Mustafa M. Aral
Keyword(s):  
Molecular Diffusion ◽  
Diffusion Constant ◽  
Interfacial Area ◽  
Laminar Flows ◽  
Fluid Mixing ◽  
Mixing Efficiency ◽  
Maximum Pressure ◽  
Small Diffusion ◽  
Passive Micromixer ◽  
Injection Type

Passive micromixers are miniaturized instruments that are used to mix fluids in microfluidic systems. In microchannels, combination of laminar flows and small diffusion constants of mixing liquids produce a difficult mixing environment. In particular, in very low Reynolds number flows, e.g., Re < 10, diffusive mixing cannot be promoted unless a large interfacial area is formed between the fluids to be mixed. Therefore, the mixing distance increases substantially due to a slow diffusion process that governs fluid mixing. In this article, a novel 3-D passive micromixer design is developed to improve fluid mixing over a short distance. Computational Fluid Dynamics (CFD) simulations are used to investigate the performance of the micromixer numerically. The circular-shaped fluid overlapping (CSFO) micromixer design proposed is examined in several fluid flow, diffusivity, and injection conditions. The outcomes show that the CSFO geometry develops a large interfacial area between the fluid bodies. Thus, fluid mixing is accelerated in vertical and/or horizontal directions depending on the injection type applied. For the smallest molecular diffusion constant tested, the CSFO micromixer design provides more than 90% mixing efficiency in a distance between 260 and 470 µm. The maximum pressure drop in the micromixer is found to be less than 1.4 kPa in the highest flow conditioned examined.

scholarly journals Novel 3-D T-Shaped Passive Micromixer Design with Helicoidal Flows

Processes ◽  
2019 ◽  
Vol 7 (9) ◽  
pp. 637 ◽  
Author(s):  
Mahmut Burak Okuducu ◽  
Mustafa M. Aral
Keyword(s):  
Fluid Flow ◽  
Fluid Mixing ◽  
Mixing Efficiency ◽  
Flow Profile ◽  
Complex Flow ◽  
Mixing Index ◽  
Micro Channels ◽  
Mixing Dynamics ◽  
Passive Micromixer ◽  
Novel Design

Laminar fluid flow and advection-dominant transport produce ineffective mixing conditions in micromixers. In these systems, a desirable fluid mixing over a short distance may be achieved using special geometries in which complex flow paths are generated. In this paper, a novel design, utilizing semi-circular ridges, is proposed to improve mixing in micro channels. Fluid flow and scalar transport are investigated employing Computational Fluid Dynamics (CFD) tool. Mixing dynamics are investigated in detail for alternative designs, injection, and diffusivity conditions. Results indicate that the convex alignment of semi-circular elements yields a specific, helicoidal-shaped fluid flow along the mixing channel which in turn enhances fluid mixing. In all cases examined, homogenous concentration distributions with mixing index values over 80% are obtained. When it is compared to the classical T-shaped micromixer, the novel design increases mixing index and mixing performance values by the factors of 8.7 and 3.3, respectively. It is also shown that different orientations of ridges adversely affect the mixing efficiency by disturbing the formation of helicoidal-shaped flow profile.

scholarly journals Designing for People’s Safety on Flooded Streets: Uncertainties and the Influence of the Cross-Section Shape, Roughness and Slopes on Hazard Criteria

Water ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2119
Author(s):  
Luís Mesquita David ◽  
Rita Fernandes de Carvalho
Keyword(s):  
Cross Section ◽  
Overland Flow ◽  
Rectangular Cross Section ◽  
Safety Hazard ◽  
Cross Section Shape ◽  
Section Shape ◽  
Flood Flows ◽  
The Cross ◽  
Flooding Risk

Designing for exceedance events consists in designing a continuous route for overland flow to deal with flows exceeding the sewer system’s capacity and to mitigate flooding risk. A review is carried out here on flood safety/hazard criteria, which generally establish thresholds for the water depth and flood velocity, or a relationship between them. The effects of the cross-section shape, roughness and slope of streets in meeting the criteria are evaluated based on equations, graphical results and one case study. An expedited method for the verification of safety criteria based solely on flow is presented, saving efforts in detailing models and increasing confidence in the results from simplified models. The method is valid for 0.1 m2/s 0.5 m2/s. The results showed that a street with a 1.8% slope, 75 m1/3s−1 and a rectangular cross-section complies with the threshold 0.3 m2/s for twice the flow of a street with the same width but with a conventional cross-section shape. The flow will be four times greater for a 15% street slope. The results also highlighted that the flood flows can vary significantly along the streets depending on the sewers’ roughness and the flow transfers between the major and minor systems, such that the effort detailing a street’s cross-section must be balanced with all of the other sources of uncertainty.

scholarly journals On the shape of cicada’s wing leading-edge cross section

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Rachel M. Starkweather ◽  
Svetlana V. Poroseva ◽  
David T. Hanson
Keyword(s):  
Cross Section ◽  
Insect Flight ◽  
Leading Edge ◽  
Flight Performance ◽  
Cross Section Shape ◽  
Section Shape ◽  
First Time

AbstractAn important role that the leading-edge cross-section shape plays in the wing flight performance is well known in aeronautics. However, little is known about the shape of the leading-edge cross section of an insect’s wing and its contribution to remarkable qualities of insect flight. In this paper, we reveal, in the first time, the shape of the leading-edge cross section of a cicada’s wing and analyze its variability along the wing. We also identify and quantify similarities in characteristic dimensions of this shape in the wings of three different cicada species.

Oxidation of Suspended Stacked Silicon Nanowire for Sub-10nm Cross-Section Shape Optimization

2019 ◽  
Vol 13 (1) ◽  
pp. 195-199 ◽  
Author(s):  
Alexandre Hubert ◽  
Jean-Philippe Colonna ◽  
Stéphane Bécu ◽  
Cécilia Dupré ◽  
Virginie Maffini-Alvaro ◽  
...  
Keyword(s):  
Shape Optimization ◽  
Cross Section ◽  
Silicon Nanowire ◽  
Cross Section Shape ◽  
Section Shape

Finite-size analysis and the influence of the cross-section shape of the granular column collapses

2021 ◽  
Author(s):  
Teng Man ◽  
Herbert Huppert ◽  
Ling Li ◽  
Sergio Galindo-Torres
Keyword(s):  
Size Effect ◽  
Cross Section ◽  
Finite Size ◽  
Size Analysis ◽  
Cross Section Shape ◽  
Section Shape ◽  
The Cross ◽  
Shape Influence ◽  
Deposition Morphology ◽  
Granular Column

&lt;p&gt;The collapse of granular columns, which sheds light on the kinematics, dynamics, and deposition morphology of mass-driven flows, is crucial for understanding complex flows in both natural and engineering systems, such as debris flows and landslides. However, our research shows that a strong size effect and cross-section shape influence exist in this test. Thus, it is essential to better understand these effects. In this study, we explore the influence of both relative column sizes and cross-section shapes on the run-out behavior of collapsed granular columns and analyze their influence on the deposition morphology with the discrete element method (DEM) with Voronoi-based spheropolyhedron particles. We link the size effect that occurs in granular column collapse problems to the finite-size scaling functions and investigate the characteristic correlation length associated with the granular column collapses. The collapsing behavior of granular columns with different cross-section shapes is also studied, and we find that particles tend to accumulate in the direction normal to the edge of the cross-section instead of the vertex of it. The differences in the run-out behavior in different directions when the cross-section is no longer a circle can also be explained by the finite-size analysis we have performed in this study. We believe that such a study is crucial for us to better understand how granular material flows, how it deposits, and how to consider the size effect in the rheology of granular flows.&lt;/p&gt;

Numerical analysis of non-aligned inputs M-type micromixers with different shaped obstacles for biomedical applications

2021 ◽  
pp. 095440892110516
Author(s):  
Muhammad Irfan ◽  
Imran Shah ◽  
Usama M Niazi ◽  
Muhsin Ali ◽  
Sadaqat Ali ◽  
...  
Keyword(s):  
Structural Design ◽  
Biomedical Applications ◽  
Structural Changes ◽  
Nanoparticle Synthesis ◽  
Fluid Mixing ◽  
The Novel ◽  
Flow Conditions ◽  
Mixing Index ◽  
Mixing Performance ◽  
Passive Micromixer

Fluid mixing in lab-on-a-chip devices at laminar flow conditions result in a low mixing index. The reason is dominant diffusion over the convection process. The mixing index can be improved by certain changes in the micromixer structural design like introducing obstacles in the path of fluid flow. These obstacles will make dominant the advection process over the diffusion process. The main contribution of this work is based on proposing the novel hybrid type micromixer design for enhancing the mixing quality. Three non-aligned M-type and non-aligned M-type with obstacles passive type micromixers are analyzed by COMSOL5.5. These designs are hybrid types because different structural changes are combined in a single design for mixing improvement. First of all the straight non-aligned inlets, M-type passive micromixer (SMTM) is analyzed. It is observed that mixing performance is improved because of M-shaped mixing units and non-aligned inlets. This improvement is deemed to be not enough so different shaped obstacles are introduced in the micromixer design. These designs based on obstacles are named horizontal rectangular M-type micromixer, square M-type micromixer, and vertical rectangular M-type micromixer. The mixing index for SMTM, square M-type micromixer, horizontal rectangular M-type micromixer, and vertical rectangular M-type micromixer at Reynolds number Re = 60 is respectively given by 71.1%, 83.21%, 84.45%, and 89.99%. The mixing index of vertical rectangular M-type micromixer was 59.34% − 87.65% for Re = 0.5–100. Vertical rectangular M-type micromixer is concluded with the better-mixing capability design among the proposed ones. Based on these simulation results, the vertical rectangular M-type micromixer design can be utilized for mixing purposes in biomedical applications like nanoparticle synthesis and biomedical sample preparation for drug delivery.

scholarly journals High Mixing Efficiency by Modulating Inlet Frequency of Viscoelastic Fluid in Simplified Pore Structure

Processes ◽  
2018 ◽  
Vol 6 (11) ◽  
pp. 210 ◽  
Author(s):  
Meng Zhang ◽  
Yunfeng Cui ◽  
Weihua Cai ◽  
Zhengwei Wu ◽  
Yongyao Li ◽  
...  
Keyword(s):  
Viscoelastic Fluid ◽  
Essential Role ◽  
Fluid Flows ◽  
Fluid Mixing ◽  
Modulation Method ◽  
Mixing Efficiency ◽  
Microscale Flow ◽  
Pressure Modulation ◽  
Active Mixing ◽  
Junction Structure

Fluid mixing plays an essential role in microscale flow systems. Here, we propose an active mixing approach which enhances the mixing of viscoelastic fluid flow in a simplified pore T-junction structure. Mixing is actively controlled by modulating the driving pressure with a sinusoidal signal at the two inlets of the T-junction. The mixing effect is numerically investigated for both Newtonian and viscoelastic fluid flows under different pressure modulation conditions. The result shows that a degree of mixing as high as 0.9 is achieved in viscoelastic fluid flows through the T-junction mixer when the phase difference between the modulated pressures at the two inlets is 180°. This modulation method can also be used in other fluid mixing devices.

Sign in / Sign up

Export Citation Format

Share Document