DESIGN OF MODIFIED FOUR-PHASE CMOS CHARGE PUMPS FOR LOW-VOLTAGE FLASH MEMORIES

2002 ◽  
Vol 11 (04) ◽  
pp. 393-403 ◽  
Author(s):  
HONGCHIN LIN ◽  
NAI-HSIEN CHEN ◽  
JAINHAO LU
Keyword(s):  
Power Efficiency ◽  
Design Methodology ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Clock Frequency ◽  
Flash Memories ◽  
Clock Generation ◽  
Charge Pumps ◽  
Main Charge

A new four-phase clock scheme for the four-phase charge pumping circuits using standard 0.5 μm CMOS technology at low supply voltages to generated high boosted voltages is proposed. Boosted clocks without high drivability are applied on the capacitors coupled to the gates of the main charge transfer transistors to compensate body effects. Thus, the high-voltage clock generation circuit can be easily achieved for clock frequency of 10 MHz. Due to the nearly ideal pumping gain per stage, the design methodology to optimize power efficiency is also presented. With the new clock scheme, it can efficiently pump to 9 V at supply voltage of 1 V using 10 stages by simulations, while pump to 4.7 V at supply voltage of 1.5 V using four stages by measurements.

scholarly journals A Design Methodology Using the Inversion Coefficient for Low-Voltage Low-Power CMOS Voltage References

2011 ◽  
Vol 6 (1) ◽  
pp. 7-17
Author(s):  
Dalton Colombo ◽  
Christian Fayomi ◽  
Frederic Nabki ◽  
Luiz F. Ferreira ◽  
Gilson Wirth ◽  
...  
Keyword(s):  
Low Power ◽  
Design Methodology ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Analog Design ◽  
Voltage Reference ◽  
Inversion Coefficient ◽  
Low Power Cmos ◽  
Traditional Approaches

This paper presents an analog design methodology, which uses the selection of the inversion coefficient of MOS devices, to design low-voltage and low-power (LVLP) CMOS voltage references. The motivation of this work comes from the demand for analog design methods that optimize the sizing process of transistors working in subthreshold operation. The advantage of the presented method – compared to the traditional approaches for circuit design – is the reduction of design cycle time and the minimization of simulation iterations when the proposed equations are used. As a case study, a LVLP voltage reference based on subthreshold MOSFETs with a supply voltage of 0.7 V was designed in a 0.18-μm CMOS technology.

scholarly journals The Demonstration of S2P (Serial-to-Parallel) Converter with Address Allocation Method Using 28 nm CMOS Technology

2021 ◽  
Vol 11 (1) ◽  
pp. 429
Author(s):  
Min-Su Kim ◽  
Youngoo Yang ◽  
Hyungmo Koo ◽  
Hansik Oh
Keyword(s):  
Integrated Circuits ◽  
Embedded System ◽  
Low Power ◽  
High Speed ◽  
Cmos Technology ◽  
Clock Frequency ◽  
Clock Generation ◽  
Allocation Method ◽  
Evaluation Board ◽  
28 Nm

To improve the performance of analog, RF, and digital integrated circuits, the cutting-edge advanced CMOS technology has been widely utilized. We successfully designed and implemented a high-speed and low-power serial-to-parallel (S2P) converter for 5G applications based on the 28 nm CMOS technology. It can update data easily and quickly using the proposed address allocation method. To verify the performances, an embedded system (NI-FPGA) for fast clock generation on the evaluation board level was also used. The proposed S2P converter circuit shows extremely low power consumption of 28.1 uW at 0.91 V with a core die area of 60 × 60 μm2 and operates successfully over a wide clock frequency range from 5 M to 40 MHz.

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

scholarly journals Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters

Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2931
Author(s):  
Waldemar Jendernalik ◽  
Jacek Jakusz ◽  
Grzegorz Blakiewicz
Keyword(s):  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Low Frequency ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Biomedical Sensors ◽  
Filter Synthesis ◽  
Cascade Method

Buffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more general method for buffer-based filter synthesis is developed and presented. The method uses RLC ladder prototypes to obtain filters of arbitrary orders. In addition, a set of novel circuit solutions with ultra-low voltage and power are proposed. The introduced circuits were synthesized and simulated using 180-nm CMOS technology of X-FAB. One of the designed circuits is a fourth-order, low-pass filter that features: 100-Hz passband, 0.4-V supply voltage, power consumption of less than 5 nW, and dynamic range above 60 dB. Moreover, the total capacitance of the proposed filter (31 pF) is 25% lower compared to the structure synthesized using a conventional cascade method (40 pF).

A CMOS Automatic Gain Control Circuit for Biomedical Applications

2015 ◽  
Vol 645-646 ◽  
pp. 1308-1313
Author(s):  
Zhi Qiang Gao ◽  
Fu Xiang Huang ◽  
Jing Li ◽  
Liang Yin ◽  
Xiao Wei Liu
Keyword(s):  
Exponential Function ◽  
Biomedical Applications ◽  
Low Voltage ◽  
Supply Voltage ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Cmos Technology ◽  
Chip Area ◽  
Gain Variation ◽  
Linearity Error

In this paper, a low-voltage automatic gain control (AGC) circuits is presented. The proposed circuit uses a novel approximated exponential function to increase the dB-linear output range. The three-stage AGC is fabricated in 0.18μm CMOS technology and shows the maximum gain variation of more than 100dB and a 67dB linear range with linearity error of less than ±1dB. The range of gain variation can be controlled from 34 to 101dB. The AGC dissipates less than 2.3mA under 1.8V supply voltage while occupying 0.4mm2 of chip area.

scholarly journals A 2.5-GHz 1-V High Efficiency CMOS Power Amplifier IC with a Dual-Switching Transistor and Third Harmonic Tuning Technique

Electronics ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 69 ◽  
Author(s):  
Taufiq Alif Kurniawan ◽  
Toshihiko Yoshimasu
Keyword(s):  
Power Amplifier ◽  
High Efficiency ◽  
Low Voltage ◽  
Supply Voltage ◽  
Drain Current ◽  
Cmos Technology ◽  
Back Gate ◽  
Third Harmonic ◽  
Power Added Efficiency ◽  
Switching Transistor

This paper presents a 2.5-GHz low-voltage, high-efficiency CMOS power amplifier (PA) IC in 0.18-µm CMOS technology. The combination of a dual-switching transistor (DST) and a third harmonic tuning technique is proposed. The DST effectively improves the gain at the saturation power region when the additional gain extension of the secondary switching transistor compensates for the gain compression of the primary one. To achieve high-efficiency performance, the third harmonic tuning circuit is connected in parallel to the output load. Therefore, the flattened drain current and voltage waveforms are generated, which in turn reduce the overlapping and the dc power consumption significantly. In addition, a 0.5-V back-gate voltage is applied to the primary switching transistor to realize the low-voltage operation. At 1 V of supply voltage, the proposed PA has achieved a power added efficiency (PAE) of 34.5% and a saturated output power of 10.1 dBm.

scholarly journals A Novel Highly Linear Voltage-To-Time Converter (VTC) Circuit for Time-Based Analog-To-Digital Converters (ADC) Using Body Biasing

Electronics ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 2033
Author(s):  
Ahmed Elgreatly ◽  
Ahmed Dessouki ◽  
Hassan Mostafa ◽  
Rania Abdalla ◽  
El-sayed El-Rabaie
Keyword(s):  
Power Consumption ◽  
Software Defined Radio ◽  
Dynamic Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
The Body ◽  
Analog To Digital Converters ◽  
Clock Frequency ◽  
Analog To Digital ◽  
Operation Speed

Time-based analog-to-digital converter is considered a crucial part in the design of software-defined radio receivers for its higher performance than other analog-to-digital converters in terms of operation speed, input dynamic range and power consumption. In this paper, two novel voltage-to-time converters are proposed at which the input voltage signal is connected to the body terminal of the starving transistor rather than its gate terminal. These novel converters exhibit better linearity, which is analytically proven in this paper. The maximum linearity error is reduced to 0.4%. In addition, the input dynamic range of these converters is increased to 800 mV for a supply voltage of 1.2 V by using industrial hardware-calibrated TSMC 65 nm CMOS technology. These novel designs consist of only a single inverter stage, which results in reducing the layout area and the power consumption. The overall power consumption is 18 μW for the first proposed circuit and 15 μW for the second proposed circuit. The novel converter circuits have a resolution of 5 bits and operate at a maximum clock frequency of 500 MHz.

A High-Linear CMOS Down Conversion Mixer Using Adjusting the Second and Third-Order Harmonic in Transconductance Stage

2014 ◽  
Vol 24 (01) ◽  
pp. 1550002 ◽  
Author(s):  
Mina Amiri ◽  
Adib Abrishamifar
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Circuit Simulation ◽  
Cmos Technology ◽  
Conversion Gain ◽  
Third Order ◽  
Cmos Mixer ◽  
Simulation Results ◽  
Down Conversion ◽  
Pmos Transistor

In this paper a new high-linear CMOS mixer is proposed. A well-known low voltage CMOS multiplier structure is used for mixer application in this paper and its linearity is provided by adjusting the value of a resistor, sizing the aspect ratio of a PMOS transistor and adding a proper value of inductor at the input stage. In simulation, a supply voltage as low as 1 V is applied to the circuit. Simulation results of improved mixer in a 0.18-μm CMOS technology illustrate 14 dB increases in IIP3 and also an increase around 1.4 dB is obtained in conversion gain. Furthermore, additional components which are used for improving linearity would not increase the power consumption and area significantly.

Design methodology for a switching-mode RF CMOS power amplifier with an output transformer

2015 ◽  
Vol 8 (3) ◽  
pp. 471-477
Author(s):  
Changhyun Lee ◽  
Changkun Park
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Design Methodology ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Rf Cmos ◽  
Power Transistor ◽  
Voltage Output ◽  
Switching Mode ◽  
Output Transformer

In this study, we propose a design methodology for a switching-mode RF CMOS power amplifier with an output transformer. For a given supply voltage, output power, and target efficiency, the initial values of the transistor size, output inductance, and capacitance can be sequentially determined during the design of the power amplifier. The breakdown voltage of the power transistor is considered in the design methodology. To prove the feasibility of the proposed design methodology, we provide the design example of a 2.4-GHz switching-mode CMOS power amplifier with 180-nm RF CMOS technology. From the measured results, the feasibility of the proposed design methodology is proved.

Sign in / Sign up

Export Citation Format

Share Document