An experimental study & analysis of effects of different parameters of microwave in production of bio-diesel

2020 ◽  
Vol 234 (4) ◽  
pp. 394-401
Author(s):  
Naveen Kumar Garg ◽  
Amit Pal
Keyword(s):  
Reaction Time ◽  
Input Power ◽  
Microwave Oven ◽  
Molar Ratio ◽  
Small Scale ◽  
Domestic Microwave Oven ◽  
Cooling Fan ◽  
Optimum Parameters ◽  
Cooling Speed ◽  
Fan Speed

A novel and rapid method for transesterifying cottonseed oil into bio-diesel using a domestic microwave oven (MW) has been developed in the present study. Five parameters were investigated to see their effect on bio-diesel yield output. These were input power, reaction time, oil-to-methanol molar ratio, turntable speed, and fan cooling speed. The respective values used for experimentation were 200 W to 500 W, 4 to 11 minutes, 1:4.5 to 1:12, 10 to 40 rpm, and 800 to 1500 rpm and the volume of the catalyst was kept constant at 1%. The experimental results of microwave study were compared to the traditional magnetic stirrer (MS) approach for the same molar ratio and catalyst amount. The optimum parameters for the transesterification process assisted by the domestic microwave oven were obtained such as methanol to oil molar ratio (1:4.5), potassium hydroxide catalyst concentration (1% (w/w)), reaction time (11 minutes), turntable speed (40 rpm) and cooling fan speed (1500 rpm). The corresponding yield of cottonseed bio-diesel (CBD (MW)) was 99.5 percent. Compared with the contemporary MS approach for the same molar ratio and catalyst number, the yield of CBD (MS) was recorded in 25 minutes as 61.23 percent. It was also found that the turntable speed and cooling fan rpm of the improved microwave oven greatly, influenced the yield of bio-diesel and facilitated better utilization of microwave energy in mixing and avoid overheating of the sample mixture. A drastic reduction in microwave input power consumption was observed as compared to the pragmatic MS approach. The findings of this study have established the utility of energy-efficient, updated domestic microwave oven in the generation of bio-diesel on a small scale.

scholarly journals A Green Synthesis of a Novel Calix[4]Resorcinarene from 7-Hydroxycitronellal Using Microwave Irradiation

2018 ◽  
Vol 18 (1) ◽  
pp. 53
Author(s):  
Ratnaningsih Eko Sardjono ◽  
Iqbal Musthapa ◽  
Iis Rosliana ◽  
Fitri Khoerunnisa ◽  
Galuh Yuliani
Keyword(s):  
Energy Consumption ◽  
Reaction Time ◽  
Microwave Irradiation ◽  
Irradiation Time ◽  
Microwave Oven ◽  
Conventional Heating ◽  
Heating Method ◽  
Microwave Assisted ◽  
Domestic Microwave Oven ◽  
Waste Production

A new versatile macromolecule cyclic C-3,7-dimethyl-7-hydroxycalix[4]resorcinarene (CDHHK4R) has been synthesized from a fragrance agent, 7-hydroxycitronellal, via microwave irradiation. The reaction utilized a domestic microwave oven at various irradiation time and power to yield an optimum condition. As a comparison, the conventional heating method was also employed for the synthesis of the same calix[4]resorcinarene. Compared to the conventional method, microwave-assisted reaction effectively reduced the reaction time, the amount of energy consumption and the waste production. It is found that the synthesis of CDHHK4R by microwave irradiation yielded 77.55% of product, higher than by conventional heating which was only 62.17%.

scholarly journals Biodiesel Production Optimization using Heterogeneous Catalyst (Al2O3) in Karanja oil by Taguchi Method

2019 ◽  
Vol 8 (4) ◽  
pp. 5555-5558
Keyword(s):  
Reaction Time ◽  
Taguchi Method ◽  
Heterogeneous Catalyst ◽  
Reaction Temperature ◽  
Production Optimization ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Small Scale ◽  
Experimental Yield ◽  
Karanja Oil

Biodiesel is renewable and environmental friendly fuel which has the potential to obtain considerable performance of engine. The aim of this work is to optimize the transesterification process for production of biodiesel using Taguchi method. In this experimental work, the Karanja oil transesterification is done to produce biodiesel using Al2O3 as a heterogeneous catalyst, using five parameters and five levels. Orthogonal array obtained by Minitab to analyze the interaction effect by using Taguchi method for the transesterification reaction. The parameters such as molar ratio of methanol to oil, catalyst concentration, reaction temperature, reaction time and stirring speed are effect on biodiesel yield. Effect of these parameters is investigated on small scale. Experimental yield obtained at optimal conditions i.e. are 20:1 molar ratio of methanol to oil, addition of 3% Al2O3 catalyst, reaction temperature 65ºC, reaction time 60 min and 600 rpm stirring speed is 80%.

scholarly journals Optimization of Biodiesel Synthesis using Heterogeneous Catalyst (SiO2) from Karanja Oil by Taguchi Method

2019 ◽  
Vol 9 (2) ◽  
pp. 5597-5600 ◽  
Keyword(s):  
Reaction Time ◽  
Taguchi Method ◽  
Heterogeneous Catalyst ◽  
Reaction Temperature ◽  
Engine Performance ◽  
Molar Ratio ◽  
Small Scale ◽  
Biodiesel Synthesis ◽  
Speed Effect ◽  
Karanja Oil

Biodiesel is renewable and environmental friendly fuel which has the capable to gain comparable engine performance. In this experimental study, Karanja oil synthesized by using Transesterification process. Transesterification of Karanja oil to biodiesel using SiO2 as a heterogeneous catalyst is studied using five different parameters and levels each. Minitab is used to fix the orthogonal arrays and Taguchi method is used to analyze the interaction effect for the transesterification reaction. The five different parameters responsible for biodiesel yield are molar ratio of methanol to oil, catalyst concentration, reaction temperature, reaction time and stirring speed. Effect of these parameters has studied on small scale. The biodiesel yield obtained experimentally at optimum conditions are 20% methanol to oil molar ratio, 3% SiO2 catalyst addition, 65ºC reaction temperature, 180 min reaction time and 500 rpm stirring speed is 77%.

scholarly journals Photocatalytic Reduction of CO2 to Methanol Using a Copper-Zirconia Imidazolate Framework

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 346
Author(s):  
Sonam Goyal ◽  
Maizatul Shima Shaharun ◽  
Ganaga Suriya Jayabal ◽  
Chong Fai Kait ◽  
Bawadi Abdullah ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalyst Support ◽  
Oxidation Potential ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Optimum Parameters ◽  
Reduction Of Co2 ◽  
Enhanced Yield

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.

scholarly journals Modified sodium molybdate as an efficient high yielding heterogeneous catalyst for biodiesel from Ghanaian indigenous Camelina sativa as a non-edible resource

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Mohammed Takase ◽  
Paul Kwame Essandoh ◽  
Rogers Kipkoech
Keyword(s):  
Reaction Time ◽  
Sodium Molybdate ◽  
Normal Pressure ◽  
Camelina Sativa ◽  
International Standards ◽  
Lewis Acidity ◽  
Molar Ratio ◽  
Solid Catalyst ◽  
Atmospheric Conditions ◽  
Heterogeneous Solid

AbstractSodium molybdate (Na2MoO4) has been synthesized and investigated as a heterogeneous solid catalyst for biodiesel from Camelina sativa seed oil. Transesterification reactions occurred under atmospheric conditions with relatively, low temperature short reaction time and normal pressure. The prepared catalyst was characterised by means of SEM, TGA, UV, XRD and FTIR. The properties of the biodiesel were compared with international standards. The transesterification reaction was very efficient with the optimum yield higher than 95% at methanol to oil molar ratio of 17:1, catalyst amount of 6%, reaction temperature of 60 °C and reaction time of 2.5 h. The molybdate complex had a high Lewis acidity and most certainly act as alcohol O–H bond leading to a transient species which has high nucleophilic character. The catalyst was easily recovered and after being washed for three times, showed capacity of recyclability for another catalytic reaction of five cycles with similar activity. The properties of the biodiesel were comparable to international standards.

scholarly journals Canard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds

2020 ◽  
Vol 37 ◽  
pp. 63-71
Author(s):  
Yui-Chuin Shiah ◽  
Chia Hsiang Chang ◽  
Yu-Jen Chen ◽  
Ankam Vinod Kumar Reddy
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Optimum Parameters ◽  
Low Wind Speeds

ABSTRACT Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.

scholarly journals Feasibility of fly ash as fluxing agent in mid- and low-grade phosphate rock carbothermal reduction and its reaction kinetics

2021 ◽  
Vol 10 (1) ◽  
pp. 157-168
Author(s):  
Biwei Luo ◽  
Pengfei Li ◽  
Yan Li ◽  
Jun Ji ◽  
Dongsheng He ◽  
...  
Keyword(s):  
Particle Size ◽  
Fly Ash ◽  
Reaction Time ◽  
Carbothermal Reduction ◽  
Industrial Waste ◽  
Phosphate Rock ◽  
Molar Ratio ◽  
Low Grade ◽  
Carbon Excess ◽  
Fluxing Agent

Abstract The feasibility of industrial waste fly ash as an alternative fluxing agent for silica in carbothermal reduction of medium-low-grade phosphate ore was studied in this paper. With a series of single-factor experiments, the reduction rate of phosphate rock under different reaction temperature, reaction time, particle size, carbon excess coefficient, and silicon–calcium molar ratio was investigated with silica and fly ash as fluxing agents. Higher reduction rates were obtained with fly ash fluxing instead of silica. The optimal conditions were derived as: reaction temperature 1,300°C, reaction time 75 min, particle size 48–75 µm, carbon excess coefficient 1.2, and silicon–calcium molar ratio 1.2. The optimized process condition was verified with other two different phosphate rocks and it was proved universally. The apparent kinetics analyses demonstrated that the activation energy of fly ash fluxing is reduced by 31.57 kJ/mol as compared with that of silica. The mechanism of better fluxing effect by fly ash may be ascribed to the fact that the products formed within fly ash increase the amount of liquid phase in the reaction system and promote reduction reaction. Preliminary feasibility about the recycling of industrial waste fly ash in thermal phosphoric acid industry was elucidated in the paper.

Degradation of chlorpyriphos in water by advanced oxidation processes

2010 ◽  
Vol 10 (1) ◽  
pp. 1-6 ◽  
Author(s):  
R. Murillo ◽  
J. Sarasa ◽  
M. Lanao ◽  
J. L. Ovelleiro
Keyword(s):  
Reaction Time ◽  
Light Source ◽  
Advanced Oxidation Processes ◽  
Advanced Oxidation ◽  
The Other ◽  
Molar Ratio ◽  
Optimum Conditions ◽  
Oxidation Processes ◽  
Other Hand ◽  
Initial Ph

The degradation of chlorpyriphos by different advanced oxidation processes such as photo-Fenton, TiO2, TiO2/H2O2, O3 and O3/H2O2 was investigated. The photo-Fenton and TiO2 processes were optimized using a solar chamber as light source. The optimum dosages of the photo-Fenton treatment were: [H2O2]=0.01 M; [Fe3 + ]=10 mg l−1; initial pH = 3.5. With these optimum conditions total degradation was observed after 15 minutes of reaction time. The application of sunlight was also efficient as total degradation was achieved after 60 minutes. The optimum dosage using only TiO2 as catalyst was 1,000 mg l−1, obtaining the maximum degradation at 20 minutes of reaction time. On the other hand, the addition of 0.02 M of H2O2 to a lower dosage of TiO2 (10 mg l−1) provides the same degradation. The ozonation treatment achieved complete degradation at 30 minutes of reaction time. On the other hand, it was observed that the degradation was faster by adding H2O2 (H2O2/O3 molar ratio = 0.5). In this case, total degradation was observed after 20 minutes.

scholarly journals Thermal treatment of superconductor thin film of the BSCCO system using domestic microwave oven

2012 ◽  
Vol 478 ◽  
pp. 56-59 ◽  
Author(s):  
J.B. Silveira ◽  
C.L. Carvalho ◽  
G.B. Torsoni ◽  
H.A. Aquino ◽  
R. Zadorosny
Keyword(s):  
Thin Film ◽  
Thermal Treatment ◽  
Microwave Oven ◽  
Bscco System ◽  
Domestic Microwave Oven
Sign in / Sign up

Export Citation Format

Share Document