A review on the corrosion resistance of electroless Ni-P based composite coatings and electrochemical corrosion testing methods

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Imtiaz Ahmed Shozib ◽  
Azlan Ahmad ◽  
Ahmad Majdi Abdul-Rani ◽  
Mohammadali Beheshti ◽  
Abdul’Azeez Abdu Aliyu
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Electrochemical Corrosion ◽  
Kelvin Probe ◽  
Corrosive Media ◽  
Measuring Techniques ◽  
Electroless Ni ◽  
The Impact ◽  
Electrode Technique

Abstract This paper aims to review the impact of different factors influencing the corrosion resistance of electroless Ni-P based coatings. Emphasis has been given onto the impact of phosphorus content, incorporation of alloying elements, addition of particles and heat treatment which have been discussed in detail and critically reviewed. The effect of corrosive media and coating process parameters on corrosion resistance are studied concisely. Furthermore, the role of the incorporation of various elements and particles’ contents on the corrosion resistance of electroless Ni-P coating are studied systematically. This paper also presents an overview of the latest electrochemical corrosion measuring techniques. The following approaches deserve special attention in the analysis: localized electrochemical impedance spectroscopy (LEIS), scanning vibrating electrode technique (SVET), scanning ion-selective electrode technique (SIET), scanning droplet cell (SDC), scanning electrochemical microscopy (SECM), scanning Kelvin probe (SKP) and novel contactless technique (NCT).

scholarly journals Zn-Co-CeO2 vs. Zn-Co Coatings: Effect of CeO2 Sol in the Enhancement of the Corrosion Performance of Electrodeposited Composite Coatings

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 704
Author(s):  
Marija Riđošić ◽  
Nebojša D. Nikolić ◽  
Asier Salicio-Paz ◽  
Eva García-Lecina ◽  
Ljiljana S. Živković ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Healing Rate ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Self Healing ◽  
Kelvin Probe ◽  
Artificial Defect ◽  
Volta Potential ◽  
Superior Corrosion Resistance ◽  
The Stability

Electrodeposition and characterization of novel ceria-doped Zn-Co composite coatings was the main goal of this research. Electrodeposited composite coatings were compared to pure Zn-Co coatings obtained under the same conditions. The effect of two ceria sources, powder and home-made sol, on the morphology and corrosion resistance of the composite coatings was determined. During the electrodeposition process the plating solution was successfully agitated in an ultrasound bath. The source of the particles was found to influence the stability and dispersity of plating solutions. The application of ceria sol resulted in an increase of the ceria content in the resulting coating and favored the refinement from cauliflower-like morphology (Zn-Co) to uniform and compact coral-like structure (Zn-Co-CeO2 sol). The corrosion resistance of the composite coatings was enhanced compared to bare Zn-Co as evidenced by electrochemical impedance spectroscopy and scanning Kelvin probe results. Zn-Co doped with ceria particles originating from ceria sol exhibited superior corrosion resistance compared to Zn-Co-CeO2 (powder) coatings. The self-healing rate of artificial defect was calculated based on measured Volta potential difference for which Zn-Co-CeO2 (sol) coatings exhibited a self-healing rate of 73.28% in a chloride-rich environment.

HIGH CORROSION RESISTANCE OF NI-P/NANO-SIO2 ELECTROLESS COMPOSITE COATINGS

2012 ◽  
Vol 05 ◽  
pp. 810-816 ◽  
Author(s):  
S.R. Allahkaram ◽  
T. Rabizadeh
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Carbon Steels ◽  
Nano Particles ◽  
Chemical Compositions ◽  
High Corrosion Resistance ◽  
Coating Type ◽  
Corrosion Behaviors ◽  
Electroless Ni

The process of electroless plating Ni - P and Ni - P /nano- SiO 2 on API-5L X65 carbon steels was improved. The Ni - P /nano- SiO 2 composite coatings were prepared from the bathes containing different concentrations of nano- SiO 2 particles. The coatings surface and morphologies were observed via scanning electron microscopy (SEM). The chemical compositions were analyzed by EDAX. The corrosion behaviors were evaluated by electrochemical impedance spectroscopy tests. The experimental results indicated that SiO 2 nano-particles co-deposited but some agglomeration occurred. Micro-hardness of electroless Ni - P - SiO 2 composite coatings increased due to the existence of nano-particles. Corrosion tests showed that both electroless Ni - P and Ni - P /nano- SiO 2 composite coatings demonstrated significant improvement of corrosion resistance of substrate in salty atmosphere and latter coating type appeared to offer a better corrosion protection.

THE CORROSION BEHAVIOR OF ELECTROLESS Ni-P-SiC NANO-COMPOSITE COATING

2008 ◽  
Vol 22 (18n19) ◽  
pp. 3031-3036 ◽  
Author(s):  
FARYAD BIGDELI ◽  
SAEED REZA ALLAHKARAM
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Electroless Nickel ◽  
Energy Dispersive Spectrum ◽  
X Ray Diffraction ◽  
Plating Bath ◽  
New Class ◽  
Nano Composite Coating ◽  
Electroless Ni

Composite coatings constitute a new class of materials which are mostly used for mechanical and tribological applications. The corrosion resistance of these composite coatings, however, has not been systematically studied and compared. In this study, electroless Ni – P composite coatings are formed on St 37 steel through the addition of nano-scale SiC particles to the plating bath. This work aimed to investigate the corrosion characteristics of electroless nickel composite coatings using electrochemical measurements which include polarization and electrochemical impedance spectroscopy tests. The morphology and structure of the composite coatings were studied by scanning electron microscopy (SEM), energy dispersive spectrum (EDS) and X-ray diffraction (XRD). The results showed that both electroless nickel and electroless nickel composite coatings demonstrated significant improvement of corrosion resistance in salty atmosphere.

scholarly journals The Corrosion Resistance of Aluminum Alloy Modified by Laser Radiation

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 672 ◽  
Author(s):  
K.M. Mroczkowska ◽  
A.J. Antończak ◽  
J. Gąsiorek
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Laser Radiation ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Radiation Energy ◽  
Ambient Air ◽  
Chloride Ions ◽  
Surface Development ◽  
The Impact

This study presents an analysis of the impact of the oxide layers, prepared utilizing fiber laser radiation (1062 nm) in ambient air with different process parameters, on the corrosion resistance of EN 5754 aluminum alloy. Due to both high corrosion resistance and high fatigue strength, a 5754 alloy is used, among others, in the marine, aerospace, automotive, and chemical industries. Nevertheless, it corrodes in aggressive environments (with high chloride ions concentration). The controlled delivery of laser radiation energy in the oxygen environment allows the formation of the oxide layer on the surface of the material. We have determined that it significantly affects the resistance of these materials to corrosion. As a result of laser irradiation, changes in the chemical structure of the surface layer (chemical composition as well as surface development) can be observed. It may exert both a positive and a negative consequence on the corrosion resistance. The electrochemical corrosion tests (potentiodynamic polarization and electrochemical impedance spectroscopy EIS) have been carried out in an aggressive environment (3% NaCl). Moreover, microscopic examination, chemical tests, and roughness were also performed. The study revealed that appropriate control of the laser process can significantly increase the original corrosion resistance of the 5754 aluminum alloy.

scholarly journals Effect of Ca Addition on Corrosion Behavior of Wrought AM60 Magnesium Alloy in Alkaline Solutions

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1172
Author(s):  
Polina Metalnikov ◽  
Guy Ben-Hamu ◽  
Kwang Seon Shin ◽  
Amir Eliezer
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Fuel Efficiency ◽  
Electrochemical Corrosion ◽  
Alkaline Solutions ◽  
Kelvin Probe ◽  
Ca Addition ◽  
Electrochemical Corrosion Behavior

Magnesium (Mg) alloys possess the lowest density among structural materials, and their application in the automotive and aircraft industries might enhance fuel efficiency. The mechanical properties can be improved by the addition of alloying elements. However, since Mg and its alloys are very susceptible to corrosion degradation, it is important to study the effect of these elements on the alloys’ corrosion behavior. In this study, 1 wt% of calcium (Ca) was added to wrought AM60 Mg alloy, and the electrochemical corrosion behavior of the alloys in alkaline solutions with and without Cl− ions was compared. The corrosion behavior was investigated by means of immersion tests, gravimetric measurements and potentiodynamic polarization (PDP); the characteristics of the oxide layer were studied by electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS). The addition of Ca resulted in precipitation of the ternary aluminum-rich (Mg-Al)2Ca phase. Scanning Kelvin probe force microscope (SKPFM) identified that this phase has a cathodic behavior relative to the α-Mg matrix; hence it can serve as additional sites for initiation of pitting corrosion. As a result, the corrosion resistance of wrought AM60 alloy with 1 wt% Ca addition deteriorated in a NaCl solution. However, in the absence of Cl− ions, alloying with Ca improves the corrosion resistance of wrought AM60 alloy due to the stabilization of the corrosion products layer. The effect of long-period immersion time on the corrosion behavior and alloy oxidation is discussed.

EVALUATION OF ELECTROLESS NI-P AND NI-P NANO-COMPOSITE COATINGS' PROPERTIES

2012 ◽  
Vol 05 ◽  
pp. 817-824 ◽  
Author(s):  
S.R. Allahkaram ◽  
A. Zarebidaki ◽  
T. Rabizadeh
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Energy Dispersive Spectrometer ◽  
Nano Particles ◽  
X Ray Diffraction ◽  
X65 Steel ◽  
Api 5L X65 Steel ◽  
Steel Substrates ◽  
Electroless Ni

SiC and SiO 2 nano-particles were co-deposited with electroless NiP coating onto API-5L-X65 steel substrates with 7g/L load of nano-particles in the bath at pH 4.6 ± 0.2 and temperature of 90 ± 2°C. The hardness and corrosion resistance of the composite coatings were measured using micro-hardness, polarization and electrochemical impedance spectroscopy techniques, respectively. Moreover, the structure of the composite coatings was investigated by means of X-ray diffraction (XRD) technique, while their morphologies and elemental compositions were analyzed using a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Results showed that co-deposited nano-particles caused an increase in the hardness of the composite coatings. Corrosion tests showed that addition of nano- SiO 2 particles improved corrosion resistance of electroless Ni - P coatings in salty atmosphere but addition of nano- SiC particles decreased, due to the agglomeration of SiC nano-particles together with an increase in the porosity of the composite coatings.

Corrosion Resistance of Nickel-Based Composite Coatings Reinforced by Spherical Tungsten Carbide

2020 ◽  
Vol 993 ◽  
pp. 1075-1085
Author(s):  
Li Fan ◽  
Hai Yan Chen ◽  
Hai Liang Du ◽  
Yue Hou ◽  
Qian Cheng
Keyword(s):  
Corrosion Resistance ◽  
Tungsten Carbide ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Salt Spray ◽  
Electrochemical Corrosion ◽  
Corrosion Properties ◽  
Oil Drilling ◽  
Passivation Film ◽  
Spherical Tungsten Carbide

Nickel-based composite coatings reinforced by spherical tungsten carbide were deposited on 42CrMo alloy steel using plasma transfer arc welding (PTAW) process. Their electrochemical corrosion properties in NaCl solution under atmospheric and high pressure were studied by polarization curve, electrochemical impedance spectroscopy. The corrosion and erosion resistance of the coatings were also investigated by salt spray corrosion and erosion corrosion tests. The results show that the self-corrosion potential of the composite coatings increased with the increase of tungsten carbide content, and the Cr element in Ni60 sample formed a stable and compact passivation film. Compared with corrosion at atmospheric pressure, the adsorption and penetration of Cl- on the coating surface enhanced due to the increase of Cl- activity under pressure, thereby to weaken the corrosion resistance. The Samples that passivated in salt spray environment, cannot completely hinder the corrosion of the coating, just only to slow down the corrosion. This study can provide theoretical basis for deep-sea oil drilling and production engineering equipment.

scholarly journals Cellulose microfibers (CMFs) reinforced smart self-healing polymeric composite coatings for corrosion protection of steel

2020 ◽  
Author(s):  
Muddasir Nawaz ◽  
Sehrish Habib ◽  
Adnan Khan ◽  
Abdul Shakoor ◽  
Ramazan Kahraman
Keyword(s):  
Corrosion Resistance ◽  
Immersion Time ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Polymeric Composite ◽  
Protective Film ◽  
Self Healing ◽  
Ph Change ◽  
Smart Coatings ◽  
Cellulose Microfibers

The use of organic coating for the metals has been widely being used to protect the surface against corrosion. Polymeric coating incorporated with Nanocontainers loaded with inhibitor and self-healing provides better corrosion resistance. Cellulose microfibers (CMFs) used as smart carriers were synthesized and loaded with dodecylamine (DOC)-inhibitor and polyethyleneimine (PEI)-both inhibitor and self-healing agents. Smart polymeric coatings were developed by mixing CMF/DOC and CMFs/PEI into the epoxy matrix. Reference coatings (that has only CMFs) were also prepared for a compersion. Scanning electron microscope (SEM), X-ray diffraction spectroscopy (XRD), Fourier transform infrared spectroscopy (FTIR) and thermal gravitational analysis (TGA) were used to confirm the loading of DOC and PEI onto the CMFs. UV-vis analysis indicates that the self-release of inhibitor from CMFs is sensitive to pH of the solution and the immersion time. Recovery of controlled surface damage confirms the decent self-healing ability of the prepared smart coatings is due to the efficient release of inhibitor (DOC) and self-healing agent (PEI) in the damaged area leading to the formation of a protective film. Electrochemical impedance spectroscopy (EIS) results demonstrate that corrosion resistance of the smart coating increases with an increase in immersion time which is due to the progressive release of inhibitors from CMFs in response to the pH change. Therefore, smart coatings demonstrate superior properties as compared to the reference coatings. The study reveals the polymeric composite coatings have potential to inhibit the corrosion of steel for oil and gas industry.

Sign in / Sign up

Export Citation Format

Share Document