Scalability of MOCVD-deposited Hafnium Oxide

2003 ◽  
Vol 765 ◽  
Author(s):  
S. Van Elshocht ◽  
R. Carter ◽  
M. Caymax ◽  
M. Claes ◽  
T. Conard ◽  
...  
Keyword(s):  
Hafnium Oxide ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Deposition Process ◽  
Oxide Thickness ◽  
Process Conditions ◽  
Primary Concern ◽  
Gate Electrode ◽  
K Value ◽  
High K

AbstractBecause of aggressive downscaling to increase transistor performance, the physical thickness of the SiO2 gate dielectric is rapidly approaching the limit where it will only consist of a few atomic layers. As a consequence, this will result in very high leakage currents due to direct tunneling. To allow further scaling, materials with a k-value higher than SiO2 (“high-k materials”) are explored, such that the thickness of the dielectric can be increased without degrading performance.Based on our experimental results, we discuss the potential of MOCVD-deposited HfO2 to scale to (sub)-1-nm EOTs (Equivalent Oxide Thickness). A primary concern is the interfacial layer that is formed between the Si and the HfO2, during the MOCVD deposition process, for both H-passivated and SiO2-like starting surfaces. This interfacial layer will, because of its lower k-value, significantly contribute to the EOT and reduce the benefit of the high-k material. In addition, we have experienced serious issues integrating HfO2 with a polySi gate electrode at the top interface depending on the process conditions of polySi deposition and activation anneal used. Furthermore, we have determined, based on a thickness series, the k-value for HfO2 deposited at various temperatures and found that the k-value of the HfO2 depends upon the gate electrode deposited on top (polySi or TiN).Based on our observations, the combination of MOCVD HfO2 with a polySi gate electrode will not be able to scale below the 1-nm EOT marker. The use of a metal gate however, does show promise to scale down to very low EOT values.

Highly Reliable Thin Hafnium Oxide Gate Dielectric

1999 ◽  
Vol 592 ◽  
Author(s):  
Laegu Kang ◽  
Byoung-Hun Lee ◽  
Wen-Jie Qi ◽  
Yong-Joo Jeon ◽  
Renee Nieh ◽  
...  
Keyword(s):  
Hafnium Oxide ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Frequency Dispersion ◽  
Deposition Process ◽  
Oxide Thickness ◽  
Mos Capacitors ◽  
Control Interface ◽  
High Resolution Tem ◽  
The One

ABSTRACTHfO2 is the one of the potential high-k dielectrics for replacing SiO2 as a gate dielectric. HfO2 is thermodynamically stable when in direct contact with Si and has a reasonable band gap (∼5.65eV). In this study, MOS capacitors (Pt/HfO2/Si) were fabricated by depositing HfO2 using reactive DC magnetron sputtering in the range of 33∼135Å followed by Pt deposition. During the HfO2 deposition, O2 flow was modulated to control interface quality and to suppress interfacial layer growing. By optimizing the HfO2 deposition process, equivalent oxide thickness (EOT) can be reduced down to ∼11.2 Å with the leakage current as low as 1X10−2 A/cm2 at +1.0V and negligible frequency dispersion. HfO2 films also show excellent breakdown characteristics and negligible hysteresis after high temperature annealing. From the high resolution TEM, there is a thin interfacial layer after annealing, suggesting a composite of Si-Hf-O with a dielectric constant of ≈ 2 X K SiO2.

Electrical Characteristics of TaOxNy/ZrSixOy Stack Gate Dielectric for MOS Device Applications

2001 ◽  
Vol 670 ◽  
Author(s):  
Hyungsuk Jung ◽  
Hyundoek Yang ◽  
Kiju Im ◽  
Hyunsang Hwang
Keyword(s):  
Interfacial Layer ◽  
Silicon Oxide ◽  
Gate Dielectric ◽  
Oxide Thickness ◽  
Tem Analysis ◽  
Mos Capacitors ◽  
Zirconium Silicate ◽  
Transmission Electron ◽  
High K ◽  
Device Applications

ABSTRACTThis letter describes a unique process for the preparation of high quality tantalum oxynitride (TaOxNy) with zirconium silicate (ZrSixOy) as an interfacial layer for use in gate dielectric applications. Compared with conventional native silicon oxide and oxynitride as an interfacial layer, tantalum oxynitride (TaOxNy) MOS capacitors using zirconium silicate (ZrSixOy) as an interfacial layer exhibit lower leakage current levels at the same equivalent oxide thickness. We were able to confirm TaOxNy/ZrSixOy stack structure by auger electron spectroscopy (AES) and transmission electron microscope (TEM) analysis. The estimated dielectric constant of TaOxNy and ZrSixOywere approximately 67 and 7, respectively. The zirconium silicate is a promising interfacial layer for future high-k gate dielectric applications.

An Advanced High-k Transistor Utilizing Metal-Organic Precursors in an ALD Deposition of Hafnium Oxide and Hafnium Silicate with Ozone as Oxidizer

2004 ◽  
Vol 811 ◽  
Author(s):  
J. Gutt ◽  
G.A. Brown ◽  
Yoshi Senzaki ◽  
Seung Park
Keyword(s):  
Hafnium Oxide ◽  
High Performance ◽  
Gate Dielectric ◽  
Electrical Characterization ◽  
Atomic Layer ◽  
Oxide Thickness ◽  
Cmos Technology ◽  
Hafnium Silicate ◽  
High K ◽  
Metal Organic

AbstractThe International Technology Roadmap for Semiconductors (ITRS) has projected that continued scaling of planar CMOS technology to the 65nm node and beyond will require development of high-k films for transistor gate dielectric applications to allow further scaling of overall device sizes according to Moore's Law [1]. Researchers have recently been studying hafnium-based high-k dielectrics as an alternative to SiO2 [2]. The method of deposition of these films has been found to impact the applicability of the films for both low standby power and high performance applications [3]. Atomic Layer Deposition (ALD) has been among the more widely studied deposition techniques for these films, but previous work has emphasized ALD utilizing inorganic precursors [4]. In this paper, we shall describe a process in which hafnium oxide and hafnium silicate films were deposited from alternating pulses of volatile metal-organic Hf/Si liquid precursors and ozone on 200mm diameter Si substrates using a single wafer ALD system. Electrical characterization of the films is presented, including equivalent oxide thickness (EOT), gate leakage, and electron mobility data, showing an achievement of EOT's ranging from 1.19 to 1.69 nm with high field mobilities from 74% to more than 90% of that of SiO2 (2.1 nm film), and Jg in the range of 80mA to 3 A/cm2.

Nitrogen (N2) Implantation to Suppress Growth of Interfacial Oxide in Mocvd Bst and Sputtered Bst Films

1999 ◽  
Vol 567 ◽  
Author(s):  
Renee Nieh ◽  
Wen-Jie Qi ◽  
Yongjoo Jeon ◽  
Byoung Hun Lee ◽  
Aaron Lucas ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Nitrogen Concentration ◽  
Chemical Vapor ◽  
Future Generation ◽  
Oxide Thickness ◽  
Layer Growth ◽  
X Ray ◽  
Bst Films

ABSTRACTBa0.5Sr0.5TiO3 (BST) is one of the high-k candidates for replacing SiO2 as the gate dielectric in future generation devices. The biggest obstacle to scaling the equivalent oxide thickness (EOT) of BST is an interfacial layer, SixOy, which forms between BST and Si. Nitrogen (N2) implantation into the Si substrate has been proposed to reduce the growth of this interfacial layer. In this study, capacitors (Pt/BST/Si) were fabricated by depositing thin BST films (50Å) onto N2 implanted Si in order to evaluate the effects of implant dose and annealing conditions on EOT. It was found that N2 implantation reduced the EOT of RF magnetron sputtered and Metal Oxide Chemical Vapor Deposition (MOCVD) BST films by ∼20% and ∼33%, respectively. For sputtered BST, an implant dose of 1×1014cm−;2 provided sufficient nitrogen concentration without residual implant damage after annealing. X-ray photoelectron spectroscopy data confirmed that the reduction in EOT is due to a reduction in the interfacial layer growth. X-ray diffraction spectra revealed typical polycrystalline structure with (111) and (200) preferential orientations for both films. Leakage for these 50Å BST films is on the order of 10−8 to 10−5 A/cm2—lower than oxynitrides with comparable EOTs.

scholarly journals Current Tunnelling in MOS Devices with Al2O3/SiO2 Gate Dielectric

2008 ◽  
Vol 2008 ◽  
pp. 1-5 ◽  
Author(s):  
A. Bouazra ◽  
S. Abdi-Ben Nasrallah ◽  
M. Said ◽  
A. Poncet
Keyword(s):  
Dielectric Constant ◽  
Gate Dielectric ◽  
Oxide Thickness ◽  
Gate Leakage ◽  
Mos Devices ◽  
High K ◽  
Carrier Trap ◽  
High Dielectric ◽  
Very High ◽  
Tunnelling Current

With the continued scaling of the SiO2 thickness below 2 nm in CMOS devices, a large direct-tunnelling current flow between the gate electrode and silicon substrate is greatly impacting device performance. Therefore, higher dielectric constant materials are desirable for reducing the gate leakage while maintaining transistor performance for very thin dielectric layers. Despite its not very high dielectric constant (∼10), Al2O3 has emerged as one of the most promising high-k candidates in terms of its chemical and thermal stability as its high-barrier offset. In this paper, a theoretical study of the physical and electrical properties of Al2O3 gate dielectric is reported including I(V) and C(V) characteristics. By using a stack of Al2O3/SiO2 with an appropriate equivalent oxide thickness of gate dielectric MOS, the gate leakage exhibits an important decrease. The effect of carrier trap parameters (depth and width) at the Al2O3/SiO2 interface is also discussed.

High quality, high-k gate dielectric: amorphous LaAlO3 thin films grown on Si(100) without Si interfacial layer

2003 ◽  
Vol 77 (5) ◽  
pp. 721-724 ◽  
Author(s):  
L. Yan ◽  
H.B. Lu ◽  
G.T. Tan ◽  
F. Chen ◽  
Y.L. Zhou ◽  
...  
Keyword(s):  
Thin Films ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
High Quality ◽  
High K ◽  
High K Gate Dielectric

scholarly journals Analog Performance of SOI nMuGFETs with Different TiN Gate Electrode Thickness and High-k Dielectrics

2011 ◽  
Vol 6 (2) ◽  
pp. 102-106
Author(s):  
Milene Galeti ◽  
Michele Rodrigues ◽  
Nadine Collaert ◽  
Eddy Simoen ◽  
Cor Claeys ◽  
...  
Keyword(s):  
Oxide Thickness ◽  
Voltage Gain ◽  
Gate Electrode ◽  
Metal Gate ◽  
Short Channel ◽  
High K ◽  
Analog Performance ◽  
Tin Metal ◽  
High K Dielectric ◽  
The Impact

This work presents an analysis of the analog performance of SOI MuGFET devices and the impact of different TiN metal gate electrode thickness.Thinner TiN metal gate allows achieving large gain and this effect can be attributed to the increased Early voltage values observed for thinner TiN metal gate. This VEA increase suggests an increase of the transversal electrical field for thin TiN metal gate (reduced gate oxide thickness) that is confirmed with the increment of the GIDL current.This impact on the voltage gain is maintained for short channel length.The impact of different gate dielectrics was also studied where high-k dielectric indicated a higher VT due to a VFB variation. Additionally, lower intrinsic voltage gain was observed for hafnium dielectric and this can be related to the lower Early voltage (VEA) present in this devices.

Sign in / Sign up

Export Citation Format

Share Document