General concept of determining the parameters of non-mining walls of ultra-deep diamond deposits development open pits

2021 ◽  
pp. 48-53
Author(s):  
I. V. Zyryanov ◽  
A. N. Akishev ◽  
I. B. Bokiy ◽  
N. M. Sherstyuk
Keyword(s):  
Rock Mass ◽  
Structural Relaxation ◽  
Slope Angle ◽  
Field Tests ◽  
Friction Angle ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Open Pit ◽  
Open Pit Mining ◽  
Relaxation Coefficient

A specific feature of open pit mining of diamond deposits in Western Yakutia is the construction of the open pits in the zone of negative ambient temperatures, which includes thick permafrost rock mass, and which is at the same time complicated by the influence of cryogenic processes on deformation of pit wall benches. The paper presents the comparative analysis of strength characteristics in frozen and thawed rocks, stability of benches during mining, the general geomechanical approach to the determination of parameters of non-mining walls of the ultra-deep open pit diamond mines, and the parameters of nonmining walls and benches. Optimization of open pit wall configuration should primarily be based on the maximum utilization of the strength properties of frozen rocks in combination with the development of new approaches, calculation schemes and methods for assessing stability of open pit walls and benches of unconventional design, including the non-mining vertical benches. The main design characteristic that determines the parameters of open pit walls is the structural tectonic relaxation coefficient, which specifies the calculated value of cohesion in rock mass. For the diamond deposits, the values of the structural relaxation coefficient were obtained in a series of field tests and back calculations. Full-scale tests were carried out both during exploration operations in underground mines and in open pits. The accuracy of determining the values of the structural relaxation coefficient in the range of 0.085–0.11 is confirmed by the parameters of non-mining walls in an open pit mine 385–640 m deep, with overall slope angles of 38–55° and a steeper H 0.35–0.5 lower part having the slope angle of up to 70° with average strength characteristics of 7.85–11.84 MPa and the internal friction angle of 28.1–37.4°. Using the natural load-bearing capacity of rock mass to the full advantage, which the values of the structural relaxation coefficient of deposits show, allows optimization of open pit wall slope design and minimization of stripping operations.

scholarly journals The Study of Parameters of Quarry Faces in Muruntau and Myutenbai Open Pits in Case of Applying Major Blasts

2019 ◽  
Vol 4 (1) ◽  
pp. 4-15
Author(s):  
B. R. Raimzhanov ◽  
A. R. Khasanov ◽  
R. R. Vakhitov
Keyword(s):  
Rock Mass ◽  
Slope Angle ◽  
Field Measurements ◽  
Geological Structure ◽  
Open Pit ◽  
Open Pit Mining ◽  
Bench Height ◽  
Before And After ◽  
Hydraulic Excavators ◽  
Parameter Field

The paper presents process layouts for excavation of zones near pit envelope based on the analysis of findings of the ore loss study in case of open-pit mining, as well as the results of field measurements in the quarry faces in Muruntau and Myutenbai open pits. In the course of the field measurements, parameters of the quarry faces at Muruntau and Myutenbai open pits were determined under the following working conditions of an excavator: at full bench with shotpile height of 19–21 m; at full bench with shotpile height of 12–14 m at excavation of the “blast cap”; at heading face and taking ramp material. In all the above-listed quarry faces, the slope angles and the ore mass shotpile height when excavating were measured. Besides, the used excavator type (dragline or hydraulic) was taken into account. For each face, 2–3 measurements were performed, and the average slope angle at the ore mass excavation was determined for each type of excavator. At the next stage of the field measurements, the bench height in the rock mass and the shotpile parameters were measured before and after blasting operations under the following arrangements for preparing the rock mass for excavation: a) under normal conditions, when the ore mass blasting is performed for the selected face or relieving wall of the required thickness; b) in compression with a “blast cap” formation; c) in the marginal parts of the bench. Based on the results of the actual bench height and the blasted rock shotpile parameter field measurements, the following conclusions were drawn: a) the actual slope angles of the quarry faces were 49° when excavating the “blast cap” using dragline excavators, and 53° when excavating the ore mass at full bench regardless of the excavator type used; the slope angles of 49° for the dragline excavator and 53° for the hydraulic excavators were taken for further calculations; b) the width of the marginal (near-envelope) zone, where losses and dilution of balance ore are generated, increased from 7 to 13.0 m (at 49°) and from 7 to 11.3 m (at 53°); as a result, the areas of loss and dilution triangles have increased; c) when blasting in compression conditions, in the upper part of the shotpile, intense mixing of the involved rock and all ore grades occurs, therefore, when excavating the “blast cap”, bulk ore mass mining is only possible. The lower part of the blasted bench preserves the geological structure of the rock mass to a greater degree and can be selectively excavated with separation of the ore mass by grade; d) when blasting the rock mass, to maintain the required pulse direction and the blasting sequence, barren boreholes are included in the breaking outline, which increase the balance ore dilution, and structural dilution arises, which should be taken into account when drawing up the "Methods for determining, limitation and accounting for ore losses and dilution in the course of the Muruntau and Myutenbai (the fifth stage) open-pit mining"; e) when compiling the "Methods ...", the option of dividing a bench of 15 m high into two sub-benches of 7.5 m should be considered.

scholarly journals Modelisation of fractured rock mass for open pit mining in Vietnam

2020 ◽  
Vol 61 (5) ◽  
pp. 80-96
Author(s):  
Tuan Anh Nguyen ◽  
Viet Van Pham ◽  
Nam Xuan Bui ◽  
Hoa Thu Thi Le ◽  
Hai Thi Le ◽  
...  
Keyword(s):  
Rock Mass ◽  
Fractured Rock ◽  
Construction Materials ◽  
Mining Operation ◽  
Open Pit ◽  
Open Pit Mining ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fractured Rock Mass ◽  
Mass Data

In open pit mining, besides the value of the minerals obtained, the cost of waste rock removal determines the efficiency of the mining operation. The paper introduces the rock mass data processing method and modelisation of fractured rock mass to serve the optimal calculation of technological stages in mining. This code is a discrete fracture network (DFN) code that couple geometrical block system construction based on modelisation stochastic with RESOBLOK simulations. The method of three-dimensional modeling (3D) of the fractured rock mass in the quarry is based on the rock mass data, the geometrical parameters of the open pit mine. From there, the rock mass simulation models were used in the analysis of the stability analysis of open pit benches, the optimization of the blast design parameters at overburden benches, project construction materials, and technology projects for block stone extraction. An application in some open pit mines such as quarries of Vietnam is presented.

scholarly journals Granulometric composition predicting models after explosion in open-pit mining

2020 ◽  
pp. 14-24
Author(s):  
Sergei Vokhmin ◽  
Keyword(s):  
Rock Mass ◽  
Granulometric Composition ◽  
Construction Materials ◽  
Production Costs ◽  
Open Pit ◽  
Open Pit Mining ◽  
Technological Problem ◽  
Total Production ◽  
Ferrous Metals ◽  
Fraction Yield

Introduction. Drilling and blasting operations are first in the workflow and significantly determine the economic efficiency of the entire mining and primary processing workflow in the enterprise. The cost of drilling and blasting operations is a significant part of total production costs of large mining companies. In this context, mining engineers today are facing a crucial technological problem, i.e. the reduction of the off-gauge fraction yield after the explosion. Research aims to develop the models which forecast the granulometric composition of the rock mass taken down as the original factor in reducing the economic waste of the entire workflow. Methodology. The parameters which influence the results of rock mass fragmentation and the techniques of rock mass granulometric composition forecasting in the course of drilling and blasting were analyzed. Results. The present paper gives a brief overview of the global mineral output; provides information on the extraction of key types of minerals (mineral fuel, ferrous metals, non-ferrous metals, precious metals, and construction materials), as well as revenues derived from their sale. On the example of domestic companies, approaches to the issue of forecasting the off-gauge fraction yield after the explosion. Summary. Direction for future actions in creating the model forecasting rock mass yield of a certain fraction after the explosion.

scholarly journals Determination of the Ultimate Underground Mining Depth considering the Effect of Granular Rock and the Range of Surface Caving

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Rongxing He ◽  
Jing Zhang ◽  
Yang Liu ◽  
Delin Song ◽  
Fengyu Ren
Keyword(s):  
Numerical Simulation ◽  
Rock Mass ◽  
Mechanical Model ◽  
Surface Deformation ◽  
Underground Mining ◽  
Mining Area ◽  
Open Pit ◽  
Open Pit Mining ◽  
Mining Depth

Continuous mining of metal deposits leads the overlying strata to move, deform, and collapse, which is particularly obvious when open-pit mining and underground mining are adjacent. Once the mining depth of the adjacent open-pit lags severely behind the underground, the ultimate underground mining depth needs to be studied before the surface deformation extends to the open-pit mining area. The numerical simulation and the mechanical model are applied to research the ultimate underground mining depth of the southeast mining area in the Gongchangling Iron mine. In the numerical simulation, the effect of granular rock is considered and the granular rock in the collapse pit is simplified as the degraded rock mass. The ultimate underground mining depth can be obtained by the values of the indicators of surface movement and deformation. In the mechanical model, the modified mechanical model for the progressive hanging wall caving is established based on Hoke’s conclusion, which considers the lateral pressure of the granular rock. Using the limiting equilibrium analysis, the relationship of the ultimate underground mining depth and the range of surface caving can be derived. The results show that the ultimate underground mining depth obtained by the numerical simulation is greater than the theoretical calculation of the modified mechanical model. The reason for this difference may be related to the assumption of the granular rock in the numerical simulation, which increases the resistance of granular rock to the deformation of rock mass. Therefore, the ultimate underground mining depth obtained by the theoretical calculation is suggested. Meanwhile, the surface displacement monitoring is implemented to verify the reasonability of the ultimate underground mining depth. Monitoring results show that the indicators of surface deformation are below the critical value of dangerous movement when the underground is mined to the ultimate mining depth. The practice proves that the determination of the ultimate underground mining depth in this work can ensure the safety of the open-pit and underground synergetic mining.

scholarly journals Study on shaping slope stability of dump in eastern grassland open-pit mine

2020 ◽  
Vol 194 ◽  
pp. 04043
Author(s):  
Guo Xiaoli ◽  
Yan Jiancheng ◽  
Li Xueliang ◽  
Wen Xin ◽  
Li Xingli
Keyword(s):  
Slope Stability ◽  
Slope Angle ◽  
Mining Area ◽  
Open Pit Mine ◽  
Open Pit ◽  
Open Pit Mining ◽  
Dump Slope ◽  
The Stability ◽  
Step Type ◽  
Mine Dump

The dumps in the open-pit mining area in the eastern grassland are prone to landslides due to the fragile ecological environment, so it is inevitable to reshape the dump slopes. In order to explore a more scientific method for slope shaping of open-pit mine dump, slope stability analysis were used to compare effect of three types of slope-type (wave-shaped, slope-shaped and step-shaped slope shaping method)in outside dumping site of Baori Hiller open-pit mine. The results show that the slope stability is negatively correlated with the slope angle, and the stability of different shaping slopes is realized as wave-shaped slope (F=2.711)> Slope-shaped slope(F=2.513)>Step-shaped slope(F=1.047), in which the wave type and slope type are all within the safe range, but the step type slope is unstable; in consideration of cost, stability and erosion resistance, it is better to set the slope angle of the dump to 15°.The wave-shaped shaping method of the natural dumping of the excavation field outside the Baori Hiller open-pit mine has the best effect and is worth promoting.

Landslide stabilization experience in Urtui open pit mine

2021 ◽  
pp. 102-106
Author(s):  
O. A. Isyanov ◽  
◽  
D. I. Ilderov ◽  
V. I. Suprun ◽  
S. A. Radchenko ◽  
...  
Keyword(s):  
Rock Mass ◽  
Large Scale ◽  
Geological Structure ◽  
Stability Control ◽  
Open Pit Mine ◽  
Open Pit ◽  
Open Pit Mining ◽  
Coal Seams ◽  
Mining Operations ◽  
Early Access

Instability of pit wall slopes is the most critical accident in open pit mining. The risk of damages to pit walls is proportional to the height of exposed surfaces and to the time of exposure. Among many factors governing pit wall stability, the major factor is geological structure and weakening zones in rock mass. Deformation processes are initiated in host rock mass of coal seams mostly because of undercutting of weak interlayers. Alongside with local undercutting, another cause of landslides is transition of coal mining from down-dip extraction to up-dip extraction. The sequence of mining and morphology of weak interlayers also have influence on initiation and evolution of deformations. The basic component of engineering solutions on pit wall stability control is optimization of mining sequence and methods of accessing working horizons in open pit mines. Large-scale deformation of Western and Southeastern pit walls in Urtui mine could be avoided using the optimized sequence of mining operations. For example, mining advance mostly along the curve of the Urtui centroclinal fold, with early access and destress of the eastern and, first of all, western wings of the fold could make it possible to evade from up-dip mining of coal seams and, as a consequence, to solve the major geomechanical problems in the open pit mine.

Sign in / Sign up

Export Citation Format

Share Document