scholarly journals Water Inrush and Failure Characteristics of Coal Seam Floor Over A Confined Aquifer

2021 ◽  
Author(s):  
Min Cao ◽  
Shangxian Yin ◽  
Bin Xu
Keyword(s):  
Coal Seam ◽  
Abutment Pressure ◽  
Water Pressure ◽  
Shear Stresses ◽  
Confined Aquifer ◽  
Working Face ◽  
Stress Coefficient ◽  
Coal Wall ◽  
Failure Depth ◽  
Seam Mining

Abstract Failure behaviors of the floor rocks under coal seam mining in the conditions of hard magma rock roof and confined aquifer are studied. Based on the theory of rock stresses and elasticity mechanics, the combined effects of the abutment pressure induced by the hard roof and by the water pressure under the thin aquicludes of the floor rocks were considered, and a mechanical model was constructed along the strike of the working face. An analytical solution of stress distribution was derived in the floor rocks, the distributions of vertical, horizontal and shear stresses were calculated. In combination with the in-situ measurement, the results show that: 1) when the periodic pressure caused by the roof collapse occurs on the working face, and the maximum stress concentration in the floor appears at the elastic-plastic junction in the direction of the strike of the working face. With the increase of the depth of the floor, the horizontal stress coefficient tends to decrease, and the corresponding shear stress coefficient isoline shows a “symmetric spiral” distribution and propagates downward to the floor at a certain angle with the vertical direction. This causes the floor rocks to generate compression and shear or tension and shear failure. 2) when the immediate roof of coal seam is the magma rock, the abutment pressure shows a trend of a slow increase initially and then a rapid increase later. The peak value of abutment pressure appears at the location of 4 - 6 meters from the coal wall of the working face, and the concentration coefficient of the abutment pressure is between 1.4 and 1.8. 3) according to the measurement and calculation of the failure depths of the floor at different positions under the same coal seam, it is found that the maximum failure depth appears near the coal wall of the working face. The failure depth reduces by 11.6% after the floor goes through “the roof caving and re-compaction”, which causes the fractures in the floor to close and the thickness of the effective aquiclude increases. In the un-mined area of the working face, the failure depth is 55% of the maximum failure depth. 4) both the theoretical calculation and the numerical simulation show that the failure depth of the floor increases obviously under the combined action of high vertical stress and the water pressure. Under the condition that the thickness of the aquiclude is relatively thin, the water pressure of the floor and pressure intensity of the roof are the sensitive factors to affect the maximum failure depth of the floor.

scholarly journals Research on Control of Rib Spalling Disaster in the Three-Soft Coal Seam

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Feng Cui ◽  
Tinghui Zhang ◽  
Xiaoqiang Cheng
Keyword(s):  
Coal Seam ◽  
Field Experiments ◽  
Simulation Experiment ◽  
Current Status ◽  
Soft Coal ◽  
Grouting Pressure ◽  
Working Face ◽  
Coal Wall ◽  
Soft Coal Seam ◽  
Seam Mining

Rib spalling disaster at the coal mining faces severely restricted the safe and efficient output of coal resources. In order to solve this problem, based on the analysis of the current status of rib spalling in the three-soft coal seam 1508 Working Face of Heyang Coal Mine, a mechanical model of sliding-type rib spalling was established and the main influencing factors that affect rib spalling are given. The mechanism of grouting technology to prevent and control rib spalling has been theoretically analyzed. A similarity simulation experiment is used to analyze the change law of roof stress under the condition of three-soft coal seam mining. The optimal grouting pressure is determined by a numerical simulation experiment. And, silicate-modified polymer grouting reinforcement materials (SMPGMs) are used in field experiments. After twice grouting operations in the 1508 Working Face, the coal wall was changed from the original soft and extremely easy rib spalling to a straight coal wall and the amount of rib spalling has been reduced by 57.45% and 48.43, respectively. And, the mining height has increased by 0.16 m and 0.23 m, respectively. The experimental results show that the rib spalling disaster of the three-soft coal seam has been effectively controlled.

scholarly journals Numerical Analysis of Stress Fields and Crack Growths in the Floor Strata of Coal Seam for Longwall Mining

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Lingzhi Sun ◽  
Yunyue Xie ◽  
Hongtian Xiao
Keyword(s):  
Coal Seam ◽  
Crack Growth ◽  
Water Pressure ◽  
Water Inrush ◽  
Coal Extraction ◽  
Additional Stress ◽  
Mining Activities ◽  
Confined Aquifer ◽  
Working Face ◽  
Distribution Features

This paper predicts the possibility of water inrush from a confined aquifer under the action of mining activities and water pressure. The study uses numerical analyses to evaluate stress redistribution and crack growth which result from coal extraction operations. Two models are presented in this study. By simplifying the distribution of the disturbed vertical stress on the coal seam and floor around a working face, a model is established to analyze the additional stresses in the floor strata induced by mining activities. And some distribution features of all the additional stress components are described. By using the superposition principle in fracture mechanics, another model is developed to analyze the crack growth in the floor strata under the action of disturbed stresses and water pressure. And the stress intensity factors at the crack tip are presented and the process of crack growth is obtained in the advancement of a working face. Because of discretizing only loading areas and crack surfaces, the present methods can obtain the accurate numerical results. Finally, some suggestions are made for preventing the water inrush from a confined aquifer.

scholarly journals Failure Characteristics and Confined Permeability of an Inclined Coal Seam Floor in Fluid-Solid Coupling

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Jian Sun ◽  
Lianguo Wang ◽  
Guangming Zhao
Keyword(s):  
Stress Concentration ◽  
Coal Seam ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Inrush ◽  
Equivalent Stress ◽  
Confined Aquifer ◽  
Confined Water ◽  
Floor Water Inrush ◽  
Failure Depth

Secondary development of FLAC3D software was carried out based on FISH language, and a 3D fluid-solid coupling numerical calculation model was established for an inclined seam mining above a confined aquifer in Taoyuan Coal Mine. A simulation study was implemented on the mining failure depth of an inclined coal seam floor, conducting height of confined water, and the position of workface floor with easy water inrush during advancement of workface. Results indicated that, during the advancement of the inclined coal seam’s workface, obvious equivalent stress concentration areas existed in the floor strata, and the largest equivalent stress concentration area was located at the low region of workface floor. When the inclined coal seam workface advanced to about 80 m, the depth of floor plastic failure zone reached the maximum at approximately 15.0 m, and the maximum failure depth was located at the low region of the workface floor. Before the inclined workface mining, original confined water conducting existed on the top interface of the confined aquifer. The conducting height of the confined water reached the maximum at about 11.0 m when the workface was pushed forward from an open-off cut at about 80 m. Owing to the barrier effect of the “soft-hard-soft” compound water-resistant strata of the workface floor, pore water pressure and its seepage velocity in the floor strata were unchanged after the workface advanced to about 80 m. After the strata parameters at the workface floor were changed, pore water pressure of the confined water could pass through the lower region of the inclined workface floor strata and break through the barrier of the “soft-hard-soft” compound water-resistant strata of the workface floor and into the mining workface, resulting in the inclined coal seam floor water inrush. Results of this study can provide a basis for predicting, preventing, and governing the inclined coal seam floor water inrush above confined aquifer.

Research of Rock Mechanical Mechanics in Steeply Dipping Seam Mining

2012 ◽  
Vol 619 ◽  
pp. 342-346 ◽  
Author(s):  
Jun Liu ◽  
Gao Wei Yue
Keyword(s):  
Numerical Simulation ◽  
Abutment Pressure ◽  
Distribution Law ◽  
Failure Characteristics ◽  
Working Face ◽  
Stress Coefficient ◽  
Rock Movement ◽  
Inclined Angle ◽  
Basic Features ◽  
Seam Mining

In steeply dipping working face rock movement, failure characteristics and distribution law of abutment pressure obviously affects seam mining. This paper takes the long wall for large inclined angle fully mechanized face of coal mine as the project background. The theoretical analysis and numerical simulation are adopted to study the break mechanism of the rock layer in steeply dipping seam mining; Through the numerical simulation results shows that the basic features are obtained, which are the biggest stress coefficient, abutment pressure of plastic area, roof weighting step，and convergence between roof and floor in working face．Based on the pressure appearance of the steeply dipping seam mining, control technology is given for the working face support stability, the work equipment prevent tumble and glide，and adjacent rock in the period of pressure. The study has a practice meaning in reducing coal mining accidents and improving the safety in steeply dipping seam mining.

Numerical Analysis of Influencing Factors of Stability in Thick Coal Seam Mining Roadway

2012 ◽  
Vol 256-259 ◽  
pp. 1453-1457
Author(s):  
Zhi Hua Li ◽  
Xin Zhu Hua ◽  
Ke Yang ◽  
Ruo Jun Zhu ◽  
De Sheng Zhou
Keyword(s):  
Coal Seam ◽  
Abutment Pressure ◽  
Surrounding Rock ◽  
Rock Body ◽  
Thick Coal Seam ◽  
Mining Depth ◽  
Working Face ◽  
Face Length ◽  
Seam Mining ◽  
Mining Height

The FLAC-3D software was used to study the surrounding rock displacement and the side abutment pressure distribution laws about roadway in thick coal seam. Based on this model, through change the mining height, working face length and mining depth, the differences of roadway underground pressure characteristics were analyzed between thick coal seam working face and normal working face. The results indicate that: ①the displacement of roadway surrounding rock increases with the increase of mining depth and mining height, the closer to the coal wall the larger of the increase range of roadway displacement. ②the peak of side abutment pressure increases with the increase of mining depth and mining height, the peak district of the stress will move toward the inner department of rock body. ③ the effect of working face length on the roadway displacement and the side abutment pressure is very feeble.

scholarly journals Stress and deformation analysis of gob-side pre-backfill driving procedure of longwall mining: a case study

2021 ◽  
Author(s):  
Rui Wu ◽  
Penghui Zhang ◽  
Pinnaduwa H. S. W. Kulatilake ◽  
Hao Luo ◽  
Qingyuan He
Keyword(s):  
Rock Mass ◽  
Stress Distribution ◽  
Coal Seam ◽  
Abutment Pressure ◽  
Longwall Mining ◽  
Vertical Stress ◽  
Floor Level ◽  
Working Face ◽  
Floor Heave ◽  
Stress And Deformation

AbstractAt present, non-pillar entry protection in longwall mining is mainly achieved through either the gob-side entry retaining (GER) procedure or the gob-side entry driving (GED) procedure. The GER procedure leads to difficulties in maintaining the roadway in mining both the previous and current panels. A narrow coal pillar about 5–7 m must be left in the GED procedure; therefore, it causes permanent loss of some coal. The gob-side pre-backfill driving (GPD) procedure effectively removes the wasting of coal resources that exists in the GED procedure and finds an alternative way to handle the roadway maintenance problem that exists in the GER procedure. The FLAC3D software was used to numerically investigate the stress and deformation distributions and failure of the rock mass surrounding the previous and current panel roadways during each stage of the GPD procedure which requires "twice excavation and mining". The results show that the stress distribution is slightly asymmetric around the previous panel roadway after the “primary excavation”. The stronger and stiffer backfill compared to the coal turned out to be the main bearing body of the previous panel roadway during the "primary mining". The highest vertical stresses of 32.6 and 23.1 MPa, compared to the in-situ stress of 10.5 MPa, appeared in the backfill wall and coal seam, respectively. After the "primary mining", the peak vertical stress under the coal seam at the floor level was slightly higher (18.1 MPa) than that under the backfill (17.8 MPa). After the "secondary excavation", the peak vertical stress under the coal seam at the floor level was slightly lower (18.7 MPa) than that under the backfill (19.8 MPa); the maximum floor heave and maximum roof sag of the current panel roadway were 252.9 and 322.1 mm, respectively. During the "secondary mining", the stress distribution in the rock mass surrounding the current panel roadway was mainly affected by the superposition of the front abutment pressure from the current panel and the side abutment pressure from the previous panel. The floor heave of the current panel roadway reached a maximum of 321.8 mm at 5 m ahead of the working face; the roof sag increased to 828.4 mm at the working face. The peak abutment pressure appeared alternately in the backfill and the coal seam during the whole procedure of "twice excavation and mining" of the GPD procedure. The backfill provided strong bearing capacity during all stages of the GPD procedure and exhibited reliable support for the roadway. The results provide scientific insight for engineering practice of the GPD procedure.

Reasonable Entry Layout of Lower Seam in Multi-Seam Mining Based on Numerical Simulation

2013 ◽  
Vol 295-298 ◽  
pp. 2980-2984
Author(s):  
Xiang Qian Wang ◽  
Da Fa Yin ◽  
Zhao Ning Gao ◽  
Qi Feng Zhao
Keyword(s):  
Numerical Simulation ◽  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mine ◽  
Abutment Pressure ◽  
Surrounding Rock ◽  
Geological Conditions ◽  
Seam Mining

Based on the geological conditions of 6# coal seam and 8# coal seam in Xieqiao Coal Mine, to determine reasonable entry layout of lower seam in multi-seam mining, alternate internal entry layout, alternate exterior entry layout and overlapping entry layout were put forward and simulated by FLAC3D. Then stress distribution and displacement characteristics of surrounding rock were analyzed in the three ways of entry layout, leading to the conclusion that alternate internal entry layout is a better choice for multi-seam mining, for which makes the entry located in stress reduce zone and reduces the influence of abutment pressure of upper coal seam mining to a certain extent,. And the mining practice of Xieqiao Coal Mine tested the results, which will offer a beneficial reference for entry layout with similar geological conditions in multi-seam mining.

scholarly journals A Mechanical Model of the Overlying Rock Masses in Undersea Coal Mining and a Stress-Seepage Coupling Numerical Simulation

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jie Fang ◽  
Lei Tian ◽  
Yanyan Cai ◽  
Zhiguo Cao ◽  
Jinhao Wen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Coal Mining ◽  
Water Inrush ◽  
Mining Area ◽  
Analysis Model ◽  
Fractured Zones ◽  
Working Face ◽  
Seam Mining ◽  
Overlying Strata

The water inrush of a working face is the main hidden danger to the safe mining of underwater coal seams. It is known that the development of water-flowing fractured zones in overlying strata is the basic path which causes water inrushes in working faces. In the engineering background of the underwater mining in the Longkou Mining Area, the analysis model and judgment method of crack propagation were created on the basis of the Mohr–Coulomb criterion. Fish language was used to couple the extension model into the FLAC3d software, in order to simulate the mining process of the underwater coal seam, as well as to analyze the initiation evolutionary characteristics and seepage laws of the fractured zones in the overlying strata during the advancing processes of the working face. The results showed that, during the coal seam mining process, the mining fractured zones which had been caused by the compression-shear and tension-shear were mainly concentrated in the overlying strata of the working face. Also, the open-off cut and mining working face were the key sections of the water inrush in the rock mass. The condition of the water disaster was the formation of a water inrush channel. The possible water inrush channels in underwater coal mining are mainly composed of water-flowing fractured zones which are formed during the excavation processes. The numerical simulation results were validated through the practical engineering of field observations on the height of water-flowing fractured zone, which displayed a favorable adaptability.

scholarly journals Comprehensive Measurement of the Deformation and Failure of Floor Rocks: A Case Study of the Xinglongzhuang Coal Mine

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Hao Liu ◽  
Pu Wang ◽  
Weihe Zhang ◽  
Qiang Liu ◽  
Lijun Su
Keyword(s):  
Coal Mine ◽  
Abutment Pressure ◽  
Three Dimensional ◽  
Strain Sensing ◽  
Floor Rock ◽  
Deformation And Failure ◽  
Working Face ◽  
Floor Failure ◽  
Coal Wall ◽  
Different Depths

The isolated island panel 10304 of the Xinglongzhuang coal mine was used as the research subject to study the deformation and damage characteristics of the coal seam floor. The damage of the floor was studied using the borehole strain sensing method and borehole imaging technology, and FLAC3D was used to study the influence of abutment pressure on floor failure. The result shows that the floor under the superimposed area which is affected by lateral and advanced abutment pressure is damaged firstly, and the maximum depth reaches 26 m, other areas of the working face about 23 m. The degree of deformation and failure of floor rock at different depths is decreased. The deformation damage increases with the advancement of the working face until a certain distance at the same depth. The hole image can clearly show the influence range of the abutment pressure in front of the coal wall and influence the degree of the advancement and lag by means of the strain increment curve for each sensor probe and the images from different drilled positions. On the basis that the results of simulation and field measurement are consistent, the results can reflect the three-dimensional failure characteristics of the whole island working face floor in the process of coal mining more comprehensively and accurately; moreover, they also can provide important information for mine flood prevention and ecological environment protection.

Sign in / Sign up

Export Citation Format

Share Document