scholarly journals Synthesis and Characterization of Nanostructure Tio2/Anthraquenone (AQ) Prepared by Sol-Gel Method

2017 ◽  
Vol 28 (1) ◽  
pp. 76
Author(s):  
Fadhela M. Hussein
Keyword(s):  
Sol Gel ◽  
X Ray Diffraction ◽  
First Order ◽  
Atomic Force ◽  
Rate Of Reaction ◽  
Ft Ir ◽  
Gel Technique ◽  
Uv Visible ◽  
Nano Titanium Dioxide

sol–gel technique conducted to synthesize nano titanium dioxide with anthraquenone (AQ) relatively in acidic pH. Nanoparticles were characterized using techniques like, Scanning Electrion Microscope (SEM), Atomic Force Microscope (AFM), UV-Visible Spectrioscopy, X-ray diffraction (XRD), Fourier transform infrared (FT-IR), SEM picture display that the TiO2/AQ is spherical in style, the band gap of TiO2/AQ nanoparticle is (3.05eV), BET and BJH analysis provides Pore volume and specific Surface area and the kinetic studie Suggest that the reaction is pseudo first order and the rate of reaction was reduce with rising initial concentration for p-Nitrotolune.

Characterization of SrBi2Nb2O9 Thin Films Prepared by Sol Gel Technique

1996 ◽  
Vol 459 ◽  
Author(s):  
E. Ching-Prado ◽  
W. Pérez ◽  
A. Reynés-Figueroa ◽  
R. S. Katiyar ◽  
D. Ravichandran ◽  
...  
Keyword(s):  
Thin Films ◽  
Raman Band ◽  
Sol Gel ◽  
Orthorhombic Symmetry ◽  
X Ray Diffraction ◽  
Ft Ir ◽  
Gel Technique ◽  
High Degree ◽  
First Time

ABSTRACTThin films of SrBi2Nb2O9 (SBN) with thicknesses of 0.1, 0.2, and 0.4 μ were grown by Sol-gel technique on silicon, and annealed at 650°C. The SBN films were investigated by Raman scatering for the first time. Raman spectra in some of the samples present bands around 60, 167, 196, 222, 302, 451, 560, 771, 837, and 863 cm−1, which correspond to the SBN formation. The study indicates that the films are inhomogeneous, and only in samples with thicknesses 0.4 μ the SBN material was found in some places. The prominent Raman band around 870 cm−1, which is the A1g mode of the orthorhombic symmetry, is assigned to the symmetric stretching of the NbO6 octahedrals. The frequency of this band is found to shift in different places in the same sample, as well as from sample to sample. The frequency shifts and the width of the Raman bands are discussed in term of ions in non-equilibrium positions. FT-IR spectra reveal a sharp peak at 1260 cm−1, and two broad bands around 995 and 772 cm−1. The bandwidths of the latter two bands are believed to be associated with the presence of a high degree of defects in the films. The experimental results of the SBN films are compared with those obtained in SBT (T=Ta) films. X-ray diffraction and SEM techniques are also used for the structural characterization.

Preparation and Characterization of Zn-Containing Hydroxyapatite/TiO2 Composite Coatings on Ti Alloys

2011 ◽  
Vol 685 ◽  
pp. 367-370 ◽  
Author(s):  
Min Qi ◽  
Da Yi Yang ◽  
Jing Ying Zhang ◽  
Hong Jun Ai
Keyword(s):  
Adhesion Strength ◽  
Composite Coatings ◽  
Energy Dispersive Spectrometer ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Zn Content ◽  
Micro Arc Oxidation ◽  
Gel Technique ◽  
Bacteria Resistance

In order to improve the osteoblast growth and bacteria resistance, Zn-containing hydroxyapatite (Zn-HA) and titanium oxide (TiO2) composite coatings were prepared to improve binding between coating and Ti substrate. TiO2 film was prepared on the surface of Ti by micro-arc oxidation (MAO) and Zn-HA coating was deposited on TiO2 using sol–gel technique. Phase structure, composition and microstructure of the surface coatings were analyzed by X-ray diffraction (XRD) and Energy Dispersive Spectrometer (EDS), respectively. The adhesion strength between the coatings with different Zn content was measured by tensile testing. The results showed that there was no significant influence of Zn content on adhesion strength between coating and Ti substrate.

Structural and Optical Characterization of Synthesized TiO2 Nanopowder Using Sol–Gel Technique

2016 ◽  
Vol 15 (01n02) ◽  
pp. 1650002 ◽  
Author(s):  
S. Lourduraj ◽  
R. Victor Williams
Keyword(s):  
Anatase Phase ◽  
Sol Gel ◽  
Visible Spectrum ◽  
Average Crystallite Size ◽  
Xrd Analysis ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Gel Technique

The nanocrystalline TiO2 powder was synthesized by sol–gel method. The XRD analysis reveals that TiO2 powder was highly crystalline (anatase phase) and nanostructured with tetragonal system. The average crystallite size after calcined at 673[Formula: see text]K is found to be 7.7[Formula: see text]nm. The surface morphological studies using scanning electron microscopy (SEM) exhibit that the formation of nanosized TiO2 particles with less densification nature. Atomic force microscopy (AFM) topography exhibits the uniform distribution of spherical-shaped particles. The energy dispersive X-ray spectroscopy (EDX) confirms the presence of Titanium and Oxygen in synthesized TiO2 nanopowder. The value of optical bandgap of TiO2 nanopowder calculated from UV-Visible spectrum is 3.45[Formula: see text]eV. The presence of TiO2 particles is confirmed from the dominant fourier transform infrared (FTIR) peaks at 621[Formula: see text]cm[Formula: see text] and 412[Formula: see text]cm[Formula: see text].

Phase transformation and characterization of TiO2 and ZrO2 addition in the Li2O–Al2O3-SiO2 gels

1996 ◽  
Vol 11 (10) ◽  
pp. 2611-2615 ◽  
Author(s):  
Ming-Hong Lin ◽  
Moo-Chin Wang
Keyword(s):  
Phase Transformation ◽  
Sol Gel ◽  
Peak Position ◽  
X Ray Diffraction ◽  
Transformation Behavior ◽  
Ceramic Powders ◽  
Higher Temperature ◽  
Gel Technique ◽  
Dta Curves

Glass-ceramic powders with a composition of Li2O · Al2O3 · 4SiO2 (LAS) have been synthesized by the sol-gel technique using LiOCH3, Al(OC2H5)3, Si(OC2H5)4, Ti(OC2H5)4, and Zr(OC2H5)4 as starting materials and the phase transformation behavior during calcination has been investigated. Differential thermal analysis (DTA), x-ray diffraction (XRD), and scanning electron microscopy (SEM) were utilized to determine the thermal behavior of the gels. Considering the LAS gels with 6.0 wt. % TiO2 and various wt. % ZrO2 content, and peak position of the β-spodumene phase formation in DTA curves was shifted to a higher temperature when the ZrO2 content was increased. The activation energy of β-spodumene crystallization was 283.8 kcal/mol for LAS gels with 6.0 wt. % TiO2 and 2.0 wt. % ZrO2. Unlike foregoing studies for LAS gels, during calcination of the dried LASTZ gels from 800 °C to 1200 °C neither β-eucryptite nor γ-spodumene was noted to be present. The crystallized phases comprised of β-spodumenes as the major phase and rutile (TiO2) together with zirconia (ZrO2) are precipitated as minor phases.

Synthesis and Characterization of Li(Li0.05Ni0.6Fe0.1Mn0.25)O2 Cathode Material for Lithim Ion Batteries

2018 ◽  
Vol 21 (1) ◽  
pp. 051-056
Author(s):  
A. Nichelson ◽  
S. Thanikaikarasan ◽  
K. Karuppasamy ◽  
S. Karthickprabhu ◽  
T. Mahalingam ◽  
...  
Keyword(s):  
Cathode Material ◽  
Sol Gel ◽  
Lithium Ion ◽  
Chelating Agent ◽  
X Ray Diffraction ◽  
Morphological Studies ◽  
New Type ◽  
Ft Ir ◽  
Ir And Raman

A new type of lithium enriched cathode material Li (Li0.05Ni0.6Fe0.1Mn0.25)O2 was synthesized by sol-gel method with citric acid as a chelating agent. The structural and morphological studies were systematically investigated through X-ray diffraction, SEM with EDS, FT-IR and Raman analyses. The crystallite size of the Li (Li0.05Ni0.6Fe0.1Mn0.25)O2 cathode material was found to be 45 nm thereby leads to the feasible movement of lithium ion all through the material. FT-IR spectroscopy was used to confirm the metal-oxygen interaction in the prepared cathode material. The electrical properties of the Li (Li0.05Ni0.6Fe0.1Mn0.25)O2 cathode material were studied by impedance and dielectric spectral analyzes. Li (Li0.05Ni0.6Fe0.1Mn0.25)O2 showed a maximum ionic conductivity of 10-6 S/cm at ambient temperature.

Microwave-Hydrothermal Synthesis and Characterization of Graphene

2012 ◽  
Vol 602-604 ◽  
pp. 917-920 ◽  
Author(s):  
Zhen Hui Xiao ◽  
Shui Sheng Wu ◽  
Yan Lin Sun ◽  
Yu Lin Zhao ◽  
Ya Ming Wang
Keyword(s):  
Chemical Reduction ◽  
Visible Spectrum ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microwave Hydrothermal ◽  
Ft Ir ◽  
Uv Visible ◽  
Scanning Electron

Graphene was synthesized by microwave-hydrothermal chemical reduction of graphite oxide using hydrazine hydrate as the reducing agent. Graphene was characterized using X-ray diffraction, UV-visible spectrum, FT-IR spectrum and scanning electron microscopy. Results indicated that the as-prepared graphene was wrinkled and comprised fewer graphenes with a highly crystalline structure.

Thick PLZT Films Grown by Sol-gel for Optical Device Applications

1998 ◽  
Vol 541 ◽  
Author(s):  
M. Linnik ◽  
O. Wilson ◽  
A. Christou
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Phase Modulator ◽  
X Ray Diffraction ◽  
X Ray ◽  
Device Applications ◽  
Gel Technique ◽  
Scanning Electron

AbstractThe preparation and characterization of thick PLZT films for spatial phase modulator applications are reported. Films were fabricated on LSCO/LAO substrates by a sol-gel technique using multiple heat-treatment parameters. The crystal quality of PLZT 9/65/35 films was investigated by X-ray diffraction and scanning electron microscopy.

Preparation and Characterization of Li4/3Ti5/3O4 Thin Films by Sol-gel Method

2006 ◽  
Vol 972 ◽  
Author(s):  
C. Hu ◽  
W. Zhang ◽  
H. Hao ◽  
M. H. Cao ◽  
S. J. Lai ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Sol Gel ◽  
High Capacity ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Atomic Force ◽  
Good Crystallinity

AbstractIn the study Li4/3Ti5/3O4 thin films were deposited on Pt substrates by sol-gel method using a spin coator. The coated films are dried at 310-360 °C, and then annealed at 500-800 °C for 30min. The prepared films were characterized by X-ray diffraction, atomic force microscope and scanning electron microscope. The results indicated that the prepared film belonged to a spinel structure and had a uniform morphology. Electrochemical properties of the prepared electrode films were evaluated by using a discharge and charge test. From these results, it can be showed that the thin film electrode annealed at 700 °C exhibited good crystallinity, smooth surface morphology, high capacity, and good rechargeability. Therefore, This film was therefore suitable for use as an anode for thin-film microbatteries.

SYNTHESIS AND CHARACTERIZATION OF HEXAMETHYLENE TETRAMINE (HMTA) CAPPED CdS NANOPARTICLES BY HYDROTHERMAL METHOD

2011 ◽  
Vol 10 (03) ◽  
pp. 441-445 ◽  
Author(s):  
M. KARL CHINNU ◽  
L. SARAVANAN ◽  
R. JAYAVEL ◽  
C. M. RAGHAVAN ◽  
K. VIJAI ANAND ◽  
...  
Keyword(s):  
Hydrothermal Method ◽  
Cadmium Acetate ◽  
Cds Nanoparticles ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Hexamethylene Tetramine ◽  
Ft Ir ◽  
Ir Analysis ◽  
Uv Visible

Cadmium sulfide nanoparticles have been synthesized by hydrothermal method using cadmium acetate, thiosemicarbazide, and sodium hydroxide as precursors with hexamethylene tetramine as the surfactant. From the X-ray diffraction analysis, it is observed that synthesized CdS nanoparticles show cubic phase. The presence of HMTA in CdS was confirmed by FT-IR analysis. The bandgap value of CdS nanostructure has been estimated by DRS–UV-Visible spectral analysis. The formation of flower-like nanoclusters was observed using scanning electron microscopy (SEM). The application of CdS nanoparticles in photocatalytic degradation was also studied.

Synthesis and Characterization of CeO2 Doped ZrO2 Ceramics by a Simple Sol-Gel Route

2017 ◽  
Vol 907 ◽  
pp. 56-60
Author(s):  
Ummuhanı Hilal Özer ◽  
Kerim Emre Öksüz ◽  
Ali Özer
Keyword(s):  
Tetragonal Phase ◽  
Sol Gel ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
Zirconia Ceramics ◽  
Simple Method ◽  
X Ray ◽  
Gel Technique

It is well known that sol-gel technique is a simple method to produce nano sized ceramic powders. In this study, cerium oxide doped zirconia samples, with 10 mol%-12mol% and14mol% CeO2, were synthesized by sol-gel technique and characterized. The surface morphology, elemental composition, microstructure, and phase analysis, of the sintered CeO2 doped ZrO2 ceramics were characterized by field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray (EDS) analysis, and X-ray diffraction (XRD) respectively. X-ray diffraction for samples sintered at 1550 °C for 4h revealed that the zirconia ceramics have a tetragonal phase structure. The addition of CeO2 can raise the content of the tetragonal phase, but the minor monoclinic phase exists even at the CeO2 content of 10 mol%. The effect of dopant concentration on the lattice parameter, average primary crystallite size and micro-strain was studied. Relative densities for CeO2 doped ZrO2 bulk ceramics varied between 95% and 99 %, depending on the CeO2 addition.

Sign in / Sign up

Export Citation Format

Share Document