scholarly journals Effect of Adding Mixture of (Concrete Waste and Asphalt Waste) on The Properties of Gypseous Soil

2019 ◽  
Vol 26 (1) ◽  
pp. 20-25
Author(s):  
Adnan Jayed zedan ◽  
Rizgar Ali Hummadi ◽  
Sarah Abdullah Hussein
Keyword(s):  
Internal Friction ◽  
Moisture Content ◽  
Asphalt Mixture ◽  
Optimum Moisture Content ◽  
California Bearing Ratio ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Angle Of Internal Friction ◽  
Density Values ◽  
Gypseous Soil

Gypseous soil which is used is taken from Tikrit city in Salah Aldeen government and specially from Tikrit University from a depth (1.5-2)m, It’s type is sandy gravely with a small percentage of silt and clay while the percentage of gypsum is (34-36)%, The tests on soil is standard proctor compaction, direct shear, collapsibility and California bearing ratio. The number of samples is (70). The effect of adding concrete waste (2, 4, 6 and 8%) and waste of Asphalt mixture (2, 4, 6 and 8) % on dry soil, as well as the effect of mixture of the optimum percentages of both additions on the properties of gypseous soil, is the aim of the study. Adding concrete waste at optimum percentage (6)% causes an increase maximum dry density at (16)% and a decrease in optimum moisture content at (5)%. Whereas adding concrete mixture waste in its optimum percentage (2)% caused a decrease in maximum dry density values with an increase of optimum moisture content, and when adding mixture of optimum percentage of waste, an increase happened in the M.D.D.(14)% with a decrease in O.M.C. at (4)%. Adding the optimum percentage (8) % for both. Value of cohesion increases (100)% when adding concrete waste with an increase in the angle of internal friction (14)% and a decrease in collapsibility in a percentage of (90)%, while adding waste of asphalt mixture shows an increase in cohesion value (112)% with a decrease in the angle of internal friction (2)%and a decrease in collapsibility in a percentage of (90)%, when adding mixture of optimum percentages the value of cohesion increase (108)% with an increase in angle of internal friction (14)%and a decrease in collapsibility in a percentage of (91)%. Values of California Bearing Ratio in dry and soaked condition increases (49)% when adding (8)% of concrete wastes which is the optimum percentage, while adding waste of asphalt mixture causes a decrease in the value of C.B.R. and the optimum percentage is (2)% , but adding optimum percentages mixture of them causes an increase in values of (52)% in dry condition and (53)% in soaked condition.

scholarly journals Strength Improvement of Weak Subgrade Soil Using Cement and Lime

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Anigilaje B Salahudeen ◽  
Ja’afar A Sadeeq
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Optimum Moisture Content ◽  
Atterberg Limits ◽  
California Bearing Ratio ◽  
Natural Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Subgrade Soil

The study investigate the suitability of subgrade soil in Baure Local Government Area of Kastina State Nigeria for road construction. The strength properties of the  subgrade was improved using lime and cement. Several analysis including the particle size distribution, specific gravity, Atterberg limits, compaction characteristics, unconfined compressive strength and California bearing ratio tests were performed on natural and lime/cement treated soil samples in accordance with BS 1377 (1990) and BS 1924 (1990) respectively. Soil specimens were prepared by mixing the soil with lime and cement in steps of 0, 3, 6, and 9% by weight of dry soil in several percentage combinations. The Atterberg limits of the weak subgrade soils improved having a minimum plasticity index value of 5.70 % at 3%Lime/6%Cement contents. The maximum dry density (MDD) values obtained showed a significant improvement having a peak value of 1.66 kN/m3 at 9%Lime/9%Cement contents. Similarly, a minimum value of 18.50 % was observed for optimum moisture content at 9%Lime/9%Cement contents which is a desirable reduction from a value of 25.00 % for the natural soil. The unconfined compressive test value increased from 167.30 kN/m2 for the natural soil to 446.77 kN/m2 at 9%Lime/9%Cement contents 28 days curing period. Likewise, the soaked California bearing ratio values increased from 2.90 % for the natural soil to 83.90 % at 9%Lime/9%Cement contents. Generally, there were improvements in the engineering properties of the weak subgrade soil when treated with lime and cement. However, the peak UCS value of 446.77 kN/m2 fails to meet the recommended UCS value of 1710 KN/m2 specified by TRRL (1977) as a criterion for adequate stabilization using Ordinary Portland Cement.            Keywords: Weak subgrade soil, Lime, Cement, Atterberg limits, Maximum dry density, Optimum moisture content, Unconfined compressive strength, California bearing ratio

scholarly journals A Proposed Approach for Evaluating Soils Optimum Moisture Content Arithmetically and Use Statistical Functions for Checking Method

2018 ◽  
Vol 7 (4.20) ◽  
pp. 287 ◽  
Author(s):  
Azhar Sadiq yasun ◽  
Jamal N. Al Abbasi
Keyword(s):  
Moisture Content ◽  
Optimum Moisture Content ◽  
Unit Weight ◽  
Average Moisture Content ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Average Value ◽  
Dry Unit Weight ◽  
Wide Range ◽  
Density Values

The processing of optimum moisture  content for specific soils as indicated by ASTM D698 specifications detail relies upon developing the fitting third or second degree bend connection between dampness content versus soil dry unit weight on a fitting bend, the registered optimum moisture  substance may contrast for a similar soil as for fitting bend figure and its position. The main objective of this study is to evaluate the optimum moisture content value based on computing average moisture content adapted from standard or modified Proctor compaction test trials and compared it with respect to the computing optimum moisture content using standard method. The research deals with a (52) compaction tests results with a wide range of optimum moisture content and dry unit weight to explore the relationships between them. The study also explores the maximum dry density values which versus standard optimum moisture content and average adopted moisture content. Statistical part depends on evaluating many statistical function values for standard and research method starts by evaluating significance of normality using Kolmogorov-Smirnov test. The average differences between standard optimum moisture content and an average value (this study depends) for moisture content was about (-0.20) and an average of differences for dry unit weight values was (0.261).  

scholarly journals Geotechnical Properties of Fresh and Degraded MSW in the Foothill of Shivalik Range Una, Himachal Pradesh

2019 ◽  
Vol 8 (2) ◽  
pp. 363-374 ◽  
Keyword(s):  
Moisture Content ◽  
Himachal Pradesh ◽  
Engineering Properties ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Overburden Pressure ◽  
Dump Site ◽  
Angle Of Internal Friction ◽  
Geotechnical Characteristics ◽  
Geotechnical Tests

The aim of the present study is to determine the physical and geotechnical characteristics of municipal solid waste (MSW) from an open dump site located in Una town, Himachal Pradesh (India) for the analysis of settlement and structural stability of landfill. Degraded waste was tested for different time intervals ranging from 6 months to 6 years. The physical characterization and the geotechnical tests were performed to determine the composition and the engineering properties of MSW respectively. The presence of moisture content in the fresh waste was 49.5±1.05% but for the degraded (or old) waste it varied between 39.8 to 51.6%. The specific gravity of fresh and old waste varied between 1.83±0.05 and 1.85 for 6 months old waste and 2.28 for 5-6 years old degraded waste respectively. The maximum dry density (MDD) was observed to be 4.28 kN/m2 for fresh waste at the optimum moisture content (OMC) of 78.1% and 4.47 kN/m3 for 6 months old waste and 6.25 kN/m3 for the degraded waste of 5-6 years at 80.2, 85.4% of OMC respectively. The hydraulic conductivity (k) of MSW was found to be decreasing with the degradation of MSW and the overburden pressure whereas the shear strength increased along with the degradation of the waste. The cohesion (c) and angle of internal friction (φ) increased respectively from 31.2 kPa(fresh) to 38 kPa(degraded) and 14° to 22° with the increase in waste degradation. The compression ratio of fresh waste was within the ranges of 0.19-0.29 and for degraded MSW it varied between 0.12 for 6 months old waste and 0.17 for 5-6 years old degraded waste respectively.

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Compaction Characteristic of Lime Modified Expansive Soil

2013 ◽  
Vol 710 ◽  
pp. 348-351
Author(s):  
Zheng Rong Zhao ◽  
Lei Wang ◽  
Hong Xia Yang
Keyword(s):  
Moisture Content ◽  
Expansive Soil ◽  
Size Composition ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Content Increase ◽  
Maximum Dry Density ◽  
Compaction Curve ◽  
Compaction Characteristic ◽  
Two Peaks

Through compaction test discussed about the compaction characteristics of expansive soil by lime modified in middle of Shandong province. The results show that the optimum moisture content is lower when the expansive soil is cured by dry compaction method, and the maximum dry density is higher. Compaction curve appeared the phenomenon of two peaks when expansive soil is cured by wet compaction method.Lime content of lime improved expansive soil, particle size composition, age and compaction function have influence on compaction curve.With the increase of the quantity of lime, the optimum moisture content increases, the maximum dry density decreases. With the age growth, the optimum moisture content increase slightly,the maximum dry density decreases slightly. The bigger the compaction work, the smaller moisture content is, the larger the maximum dry density is.

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

scholarly journals COMPACTION ASSESSMENT OF RECYCLED AGGREGATES FOR USE IN UNBOUND SUBBASE APPLICATION

2014 ◽  
Vol 20 (2) ◽  
pp. 169-174 ◽  
Author(s):  
Vahid Ayan ◽  
Mukesh C. Limbachiya ◽  
Joshua R. Omer ◽  
Seyyed Masoud Nasr Azadani
Keyword(s):  
Moisture Content ◽  
Asphalt Pavement ◽  
Optimum Moisture Content ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Dry Density ◽  
Reclaimed Asphalt Pavement ◽  
Maximum Dry Density ◽  
Reclaimed Asphalt ◽  
Natural Aggregates

Study was recently conducted at Kingston University to assess the suitability of using recycled concrete aggregate (RCA) and reclaimed asphalt pavement (RAP) in unbound subbase mixtures. The results showed that the use of 100% recycled aggregates increased the optimum moisture content and decreased the maximum dry density of the sub-base materials in comparison with natural aggregates. Moreover, the replacement of RCA by reclaimed asphalt pavement by 50% decreased the optimum moisture content and increased the maximum dry density in proportion to 100% RCA. The effects of physical properties on 0% air void and compaction curve were discussed for each type of subbase. The CBR values of the subbase materials prepared with 100%RCA is lower than subbase mixture with 100% natural aggregates. The CBR further decreased for replaced subbase with RAP so that 50%RCA + 50%RAP is not suitable for unbound subbase from the point of CBR view. In each mix the trend of CBR value was investigated in terms of water content. This research found some significant practical points to use in site works.

Analysis for Influence Factors of Cold Recycling Mixture Compaction Test

2012 ◽  
Vol 204-208 ◽  
pp. 1633-1637
Author(s):  
Yong Bing Wang ◽  
Guo Qiang Ying ◽  
Jian Lin Hu ◽  
Hua Wei Wei ◽  
Qian Zhang
Keyword(s):  
Moisture Content ◽  
Water Absorption ◽  
Base Material ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Surface Material ◽  
Test Results ◽  
Maximum Dry Density ◽  
Compaction Test ◽  
Recycled Material

In order to study the factors which influence the inorganic binder stabilized material’s compaction test results, different recycled material content therefore different reclaimed gradation mixtures are tested while varying the amount of cement. The experiment results show that contents of the recycled base material and the recycled surface material on the compaction test results are determined by the change of their density and water absorption ratio. Dry density of the recycled mixture increases with the increase of the reclaimed base material density. Low water absorption ratio of the recycled material reduces the reclaimed mixture’s optimum moisture content. Density of the reclaimed wearing surface material reduces the maximum dry density of the reclaimed mixture because the old wearing surface material has lower density. Its low water absorption reduces the optimum moisture content of the recycled mixture. Influence of cement content on compaction test results is the increase of the cement content can enhance the maximum dry density and optimum moisture content of the recycled material. Through the analysis of the results of the compaction test, the key factors in the recycled material compaction test are unveiled.

Study of Key Parameters in the Process of Aeolian Sand Compactibility

2014 ◽  
Vol 580-583 ◽  
pp. 278-282
Author(s):  
Ying Zi Yin ◽  
Ya Lei Wang
Keyword(s):  
Moisture Content ◽  
Inner Mongolia ◽  
Retaining Wall ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Aeolian Sand ◽  
Maximum Dry Density ◽  
Factors Affecting ◽  
Practical Engineering ◽  
Vibration Impact

The main factors affecting soil compatibility include moisture content, compaction work, soil type, grading and coarse material content etc.. The effects of compaction work are as follows: the stronger compaction work is, the more larger soil dry density is. The optimum moisture content decreases with the compaction work increasing. This paper mainly studies the effect of compaction work to aeolian sand compatibility. Its lay-down thickness is about 30-50cm when we use vibratory roller to compact aeolian sand in practical engineering. This paper analysis’s and studies the maximum dry density and the optimum moisture content of aeolian sand in the middle region of Inner Mongolia, and achieves its lay-down thicknesses are 30cm,40cm,and 50cm respectively at the optimum moisture content. We use 85kg vibration-impact rammer instead of YZ 18 vibratory roller to simulate the aeolian sand compaction effect at the optimum moisture content. The specification does not specify the number of compatibility times, but it is generally 3 to 5 times in the actual project .We choose the most suitable compatibility times and lay-down thickness through anglicizing the Aeolian sand compactness for vibration-impact rammer rolling on eloign sand 3 times,4 times, and 5 times respectively at 3 different kinds of lay-down thicknesses. Through the study of the Inner Mongolia area Aeolian sand, it provides a useful reference for highway and railway construction in the desert area as well as the encapsulated layer thickness of reinforced retaining wall, a new type support structure.

Sign in / Sign up

Export Citation Format

Share Document