scholarly journals Mechanical Characteristics and Failure Modes of Low-Strength Rock Samples with Dissimilar Fissure Dip Angles

2021 ◽  
Author(s):  
Y L Wang ◽  
D S Liu ◽  
K Li ◽  
X M Hu ◽  
D Chen
Keyword(s):  
Rock Mass ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
High Strength ◽  
Rock Masses ◽  
Deformation And Failure ◽  
Deformation Features ◽  
Low Strength ◽  
Dip Angle ◽  
Strength Rock

The mechanical characteristics and failure modes of low-strength rock sample with various fissure dip angles were investigated by conventional uniaxial compression test and three-dimensional (3D) crack reconstruction. The results indicated that compared with high-strength rock masses, cracks had different influences on the low-strength rock mass mechanical deformation features. Thereinto, the dip angle of fissures can cause post-peak failure stage of stress-strain curve change from swift decline to multi-step down, showing obvious ductility deformation and failure characteristics. Peak strength and elastic modulus owned an anti-S-shaped growth tendency with the growth of fissure dip angle, which was positively correlated and greatest subtle to the fissure dip angle α < 21° and α > 66.5°. The axial peak strain reduced first and enlarged rapidly with growing fissure dip angle, suggesting a V-shaped change trend. Increasing the fissure dip angle will change the sample failure mode, experienced complete tensile failure to tensile-shear composite failure, and ultimately to typical shear failure. Also, the crack start angle decreased with enlarging fissure dip angle, larger than that the high-strength rock mass fissure dip angle. The above research findings can complement and improve the study of fissured rock masses.

scholarly journals Mechanical Characteristics and Failure Modes of Low-Strength Rock Samples with Dissimilar Fissure Numbers

2021 ◽  
Author(s):  
Y L Wang ◽  
D S Liu ◽  
K Li ◽  
D Chen ◽  
X M Hu
Keyword(s):  
Mechanical Characteristics ◽  
Failure Modes ◽  
Three Dimensional ◽  
Strain Curve ◽  
Uniaxial Compression Test ◽  
Rock Masses ◽  
Deformation And Failure ◽  
Deformation Features ◽  
Low Strength ◽  
Strength Rock

The mechanical characteristics and failure modes of low-strength rock sample with various crack dip angles and numbers were investigated by conventional uniaxial compression test and three-dimensional (3D) crack reconstruction. The results indicated that compared with high-strength rock masses, cracks had different influences on the low-strength rock mass mechanical deformation features. Thereinto, the number of fissures can cause post-peak failure stage of stress-strain curve change from swift decline to multi-step down and horizontally extended decline, respectively, showing obvious ductility and ductile-flow deformation and failure characteristics. Due to the structural effect, only under the condition of fissure α < 90°, the modulus of peak strength and elastic modulus lowered with the enhancement of fissure number and had a negative correlation. As the number of fissures increased, the axial peak strain increased first and then decreased, demonstrating a reversed V-shaped change trend. Fissure number can fully affect the crack propagation law only in the case of vertical fissures. The above research findings can complement and improve the study of fissured rock masses.

scholarly journals Key Factors Affecting the Deformation and Failure of Surrounding Rock Masses in Large-Scale Underground Powerhouses

2020 ◽  
Vol 2020 ◽  
pp. 1-20
Author(s):  
Meng Wang ◽  
Jia-wen Zhou ◽  
An-chi Shi ◽  
Jin-qi Han ◽  
Hai-bo Li
Keyword(s):  
Rock Mass ◽  
Large Scale ◽  
Surrounding Rock ◽  
Rock Masses ◽  
Affecting Factors ◽  
Key Factors ◽  
Underground Powerhouse ◽  
Deformation And Failure ◽  
Factors Affecting ◽  
Geological Conditions

The stability of the surrounding rock masses of underground powerhouses is always emphasized during the construction period. With the general trends toward large-scale, complex geological conditions and the rapid construction progress of underground powerhouses, deformation and failure issues of the surrounding rock mass can emerge, putting the safety of construction and operation in jeopardy and causing enormous economic loss. To solve these problems, an understanding of the origins and key affecting factors is required. Based on domestic large-scale underground powerhouse cases in the past two decades, key factors affecting the deformation and failure of the surrounding rock mass are summarized in this paper. Among these factors, the two most fundamental factors are the rock mass properties and in situ stress, which impart tremendous impacts on surrounding rock mass stability in a number of cases. Excavation is a prerequisite of surrounding rock mass failure and support that is classified as part of the construction process and plays a pivotal role in preventing and arresting deformation and failure. Additionally, the layout and structure of the powerhouse are consequential. The interrelation and interaction of these factors are discussed at the end of this paper. The results can hopefully advance the understanding of the deformation and failure of surrounding rock masses and provide a reference for design and construction with respect to hydroelectric underground powerhouses.

Failure Mode Analysis of Bedding Rock Slope Affected by Rock Mass Structural Plane

2014 ◽  
Vol 602-605 ◽  
pp. 594-597 ◽  
Author(s):  
En An Chi ◽  
Tie Jun Tao ◽  
Ming Sheng Zhao ◽  
Qiang Kang
Keyword(s):  
Rock Mass ◽  
Slope Failure ◽  
Failure Modes ◽  
Shear Stiffness ◽  
Mode Analysis ◽  
Structural Plane ◽  
Plane Failure ◽  
Failure Mode Analysis ◽  
Dip Angle ◽  
The Impact

Based on the discrete element numerical simulation, the change of failure modes of slope influenced by parameters of rock mass structural plane is studied. It is shown the failure modes shift gradually from the bedding sliding failure modes to the sliding-bending failure modes with the increase of the strength of the rock mass structural plane; The slope failure modes are mainly sliding failure modes with the increasing of the normal and shear stiffness and spacing of rock structural plane. Failure modes shift from shearing slip failure modes to shearing slip and buckling failure modes and finally to the tilting failure modes with the increase of the rock structural plane dip angle. The impact of the rock structural plane cohesion to the slope stability is the greatest, and the stiffness is the least.

scholarly journals Numerical Modeling on Dynamic Characteristics of Jointed Rock Masses Subjected to Repetitive Impact Loading

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Jie Liu ◽  
Yan-Bin Song ◽  
Yue-Mao Zhao
Keyword(s):  
Rock Mass ◽  
Impact Loading ◽  
Jointed Rock ◽  
Stress Waves ◽  
Rock Masses ◽  
Jointed Rock Masses ◽  
Numerical Tests ◽  
Repetitive Impact ◽  
Dip Angle ◽  
Energy Dissipated

A discrete element method code was used to investigate the damage characteristics of jointed rock masses under repetitive impact loading. The Flat-Joint Contact Model (FJCM) in the two-dimensional particle flow code (PFC2D) was used to calibrate the microparameters that control the macroscopic behavior of the rock. The relationship between macro- and microparameters by a series of uniaxial direct tension and compression numerical tests based on an orthogonal experimental design method was obtained to calibrate the microparameters accurately. Then, the Synthetic Rock Mass (SRM) method that incorporates joints into the calibrated particle model was used to construct large-scale jointed rock mass specimens, and the repetitive drop hammer impact numerical tests on SRM specimens with different numbers of horizontal joints and dip angle joints were carried out to study the damage evolution, stress wave propagation, and energy dissipation characteristics. The results show that the greater the number of joints, the greater the number of cracks generated, the greater the degree of damage, and the more energy dissipated for rock masses with horizontal joints. The greater the dip angle of joints, the less the number of cracks generated, the less the degree of damage, and the less energy dissipated for rock masses with different dip angles of joints. The impact-induced stress waves will be reflected when they encounter preexisting joints in the process of propagation. When the reflected stress waves meet with subsequent stress waves, the stress waves will change from compressional waves to tensile waves, producing tensile damage inside rock masses.

scholarly journals Deformation and Failure Analyses of the Surrounding Rock Mass with an Interlayer Shear Zone in the Baihetan Underground Powerhouse

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Fei Yuan ◽  
An-chi Shi ◽  
Jia-wen Zhou ◽  
Wang-bing Hong ◽  
Meng Wang ◽  
...  
Keyword(s):  
Rock Mass ◽  
Shear Deformation ◽  
Shear Zone ◽  
Failure Modes ◽  
Shear Zones ◽  
Surrounding Rock ◽  
Left Bank ◽  
Underground Powerhouse ◽  
Deformation And Failure ◽  
Interlayer Shear

In the process of underground cavern excavation, the existence of the interlayer shear zones or large faults often makes the surrounding rock tend to be unstable or even deformed. Under the influence of interlayer shear zone C2, different degrees of deformation and failure occurred in many parts during the excavation of the Baihetan left bank underground powerhouse. Based on field monitoring and numerical calculation, this paper studies the deformation and failure characteristics of the rock mass with C2 in the whole excavation process and the failure mechanisms are analyzed. The results show that C2 has poor mechanical properties. In the process of excavation, it mainly induces two failure modes: rock collapse and shear deformation, which specifically leads to rock collapses, large deformation and shotcrete cracking in the main powerhouse, and shear deformation in the omnibus bar caves. In addition, the similarities and differences between this study and other studies on the deformation and failure of surrounding rock of underground powerhouse in recent years are discussed, and the relevant treatment measures for C2 are given. The above research results can be a reference for other related studies.

scholarly journals A New Method for Automatic Extraction and Analysis of Discontinuities Based on TIN on Rock Mass Surfaces

2021 ◽  
Vol 13 (15) ◽  
pp. 2894
Author(s):  
Xiang Wu ◽  
Fengyan Wang ◽  
Mingchang Wang ◽  
Xuqing Zhang ◽  
Qing Wang ◽  
...  
Keyword(s):  
Rock Mass ◽  
Clustering Algorithm ◽  
Point Clouds ◽  
New Method ◽  
Rock Masses ◽  
Average Deviation ◽  
Density Peaks ◽  
3D Point Clouds ◽  
Discontinuity Sets ◽  
Dip Angle

Light detection and ranging (LiDAR) can quickly and accurately obtain 3D point clouds on the surface of rock masses, and on the basis of this, discontinuity information can be extracted automatically. This paper proposes a new method to automatically extract discontinuity information from 3D point clouds on the surface of rock masses. This method first applies the improved K-means algorithm based on the clustering algorithm by fast search and find of density peaks (DPCA) and the silhouette coefficient in the cluster validity index to identify the discontinuity sets of rock masses, and then uses the hierarchical density-based spatial clustering of applications with noise (HDBSCAN) algorithm to segment the discontinuity sets and to extract each discontinuity from a discontinuity set. Finally, the random sampling consistency (RANSAC) method is used to fit the discontinuities and to calculate their parameters. The 3D point clouds of the typical rock slope in the Rockbench repository is used to extract the discontinuity orientations using the new method, and these are compared with the results obtained from the classical approach and the previous automatic methods. The results show that, compared to the results obtained by Riquelme et al. in 2014, the average deviation of the dip direction and dip angle is reduced by 26% and 8%, respectively; compared to the results obtained by Chen et al. in 2016, the average deviation of the dip direction and dip angle is reduced by 39% and 40%, respectively. The method is also applied to an artificial quarry slope, and the average deviation of the dip direction and dip angle is 5.3° and 4.8°, respectively, as compared to the manual method. Furthermore, the related parameters are analyzed. The study shows that the new method is reliable, has a higher precision when identifying rock mass discontinuities, and can be applied to practical engineering.

scholarly journals ENGINEERING GEOLOGICAL BEHAVIOUR OF HETEROGENEOUS AND CHAOTIC ROCK MASSES

2017 ◽  
Vol 43 (1) ◽  
pp. 183 ◽  
Author(s):  
G. Tsiambaos
Keyword(s):  
Rock Mass ◽  
Mechanical Behaviour ◽  
Mechanical Characteristics ◽  
Rock Masses ◽  
Rock Mass Strength ◽  
Matrix Strength ◽  
The Matrix ◽  
Scientists And Engineers ◽  
Geological Formations

The engineering characterization of heterogeneous and complex geological formations for estimating their rock mass strength and deformability characteristics constitutes a challenge to geo-scientists and engineers dealing with the design and construction of slopes and tunnels. Mélanges and similar heterogeneous mixtures of hard blocks in weaker matrix, known as “bimrocks”, present an overall strength significantly greater than the matrix strength, because the presence of rock blocks, above a threshold volumetric proportion, influences the mechanical characteristics and the behaviour of these rock masses. Moreover, recent studies have shown that the strength and mechanical behaviour of heterogeneous and composite rock masses such as flysch and molasses consisting of alternating layers of competent and incompetent rocks are governed by the presence and volumetric percentage of the interlayers of the weaker rocks.

scholarly journals Stability Analysis and Reliability Evaluation in Cataclastic Loose Rock Mass Blocks

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Liguo Zhang ◽  
Dong Wang ◽  
Guanghe Li ◽  
Jiaxing Dong ◽  
Junpeng Zhang
Keyword(s):  
Rock Mass ◽  
System Reliability ◽  
Laser Scanning ◽  
Failure Modes ◽  
Reliability Evaluation ◽  
Rock Slopes ◽  
Hydropower Project ◽  
Rock Masses ◽  
Cataclastic Rock ◽  
Key Block

Cataclastic rock masses with multiple failure modes and mechanisms are critical geological problems in the construction of rock slopes. Cataclastic rock masses are widely distributed in slopes of a hydropower project located on Lancang River, which is located in Tibet, China. In this study, the potentially unstable block of the slope is divided into key block and secondary key block based on the key block theory, and the system reliability evaluation theory is introduced. The method for quantitatively analyzing the rock mass stability of cataclastic slopes with sliding failure is established. Then, the spatial distribution of cataclastic rock masses and discontinuities in several rock slopes of a hydropower project are determined using traditional geological surveying and 3D laser scanning. At last, combining the BATE 2.0 software and the stereographic projection of the vector, the proposed method is applied to the study area. The results show that the main failure mode of the studied slope is wedge failure, and the system reliability is 1.69. With the increase in the instability probability of the key block, the increase in the instability probability of the system block is obvious, which reflects the controlling effect of the key block on the stability of the system block. The calculated system instability probability is slightly larger than the key block instability probability.

scholarly journals Experimental study on crack characteristics and acoustic emission characteristics in rock-like material with pre-existing cracks

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ji-Shun Pan ◽  
Shuang-Xi Yuan ◽  
Tong Jiang ◽  
Cheng-Hao Cui
Keyword(s):  
Grain Size ◽  
Acoustic Emission ◽  
Rock Mass ◽  
Axial Load ◽  
Mechanical Characteristics ◽  
Size Range ◽  
Bottom Surface ◽  
Emission Characteristics ◽  
Rock Masses ◽  
Acoustic Emission Energy

AbstractGrain size composition, crack pattern, and crack length have a significant influence on the crack characteristics, mechanical characteristics, and acoustic emission characteristics of rock masses. In this paper, the crack characteristics, mechanical characteristics, and acoustic emission characteristics of rock masses with different grain size compositions, different crack patterns, and different crack lengths were investigated under uniaxial compression. The rock masses were made of rock-like materials. The crack initiation locations and crack propagation directions were different for a specimen comprised of one grain size range compared with specimens comprised of two or three grain size ranges. The specimens comprised of one and three grain size ranges crack progressively. The specimen comprised of two-grain size ranges brittle fracture. The highest peak axial load was found in the specimens comprised of one grain size range. The results showed that tensile wing crack, anti-tensile wing crack, transverse shear crack, compression induced tensile crack, and surface spalling were produced in specimens with different crack orientations. The rock mass with 2 cm long crack started to produce cracks from the tip of the crack extending to the top and bottom surface, soon forming through cracks. The rock was brittle fracture. The axial load reached the maximum and then fell rapidly. The acoustic emission energy reached a rapid maximum and then decreased rapidly. The rock mass with 3 cm long fissures started to produce cracks that only extended from the tip of the fissures to the top surface but not to the bottom surface. The rock mass was progressively fractured. The axial load was progressively decreasing. The acoustic emission energy also rose and fell rapidly several times as the rock mass was progressively fractured. Different rock crack lengths led to different crack processes and crack patterns, resulting in very different acoustic emission characteristics.

Sign in / Sign up

Export Citation Format

Share Document