scholarly journals Polymer Matrix Composite in High Voltage Applications: A Review

2021 ◽  
Vol 12 (6) ◽  
pp. 8343-8352
Keyword(s):  
Composite Materials ◽  
High Voltage ◽  
Low Cost ◽  
Natural Fibers ◽  
Weight Ratio ◽  
High Strength ◽  
Design Parameters ◽  
Shielding Effectiveness ◽  
Structural Composites ◽  
Low Thermal Expansion

In recent years, natural fibers have become more widely used as reinforcement in polymer composites to generate low-cost products. Fibrous reinforcements in polymer matrices lead to good mechanical and electrical properties for composite materials. Depending on the grade and orientation, composites can be one-fifth the weight of steel while offering similar or better stiffness and strength. In addition, unlike steel or aluminum, composites do not rust or corrode. Composite materials reinforcing phase gives durability, strength, and stiffness. Composite materials have traditionally been employed as structural materials. Composite materials are increasingly being used in electrical applications such as bushings, circuit breakers, coupling capacitors, and so on, thanks to the growing growth of the electrical sector. The design parameters for structural and electrical composites differ dramatically due to the enormous differences in property requirements. Depending on the application, structural composites. Structural composites prioritize sufficient strength and modulus, while electrical composites prioritize superior dielectric constant, thermal conductivity and low thermal expansion, and shielding effectiveness. In the electrical industry, low density is desired because it allows for weight reduction. It is also desirable to have a high strength-weight ratio and dielectric properties. This paper provides a brief review of the properties of polymer composite materials and their application in the high voltage industry.

SYNTHESIS AND CHARACTERISATION OF WOVENROVING GLASS MAT FOR EPOXYCOMPOSITES

2020 ◽  
Vol 15 (4) ◽  
Author(s):  
Mahesh Mallampati ◽  
Sreekanth Mandalapu ◽  
Govidarajulu C
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Low Cost ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Test ◽  
Industrial Applications ◽  
Sem Analysis ◽  
Low Thermal Expansion ◽  
Manufacturing Techniques

The composite materials are replacing the traditional materials because oftheir superior properties such as high tensile strength, low thermal expansion, high strength to weight ratio, low cost, lightweight, high specific modulus, renewability and biodegradability which are the most basic & common attractive features of composites that make them useful for industrial applications. The developments of new materials are on the anvil and are growing day by day. The efforts to produce economically attractive composite components have resulted in several innovative manufacturing techniques currently being used in the composites industry. Generally, composites consist of mainly two phases i.e., matrix and fiber. In this study, woven roving mats (E-glass fiber orientation (-45°/45°,0°/90°, - 45°/45°),UD450GSM)were cut in measured dimensions and a mixture of Epoxy Resin (EPOFINE-556, Density-1.15gm/cm3), Hardener (FINE HARDTM 951, Density- 0.94 gm/cm3) and Acetone [(CH3)2CO, M= 38.08 g/mol] was used to manufacture the glass fiber reinforced epoxy composite by hand lay-up method. Mechanical properties such as tensile strength, SEM analysis, hardness test, density tests are evaluated.

scholarly journals Design and Analysis of Composite Leaf Spring

2013 ◽  
pp. 209-212
Author(s):  
Y. N. V. Santhosh Kumar ◽  
M. Vimal Teja
Keyword(s):  
Composite Materials ◽  
Automobile Industry ◽  
Composite Structures ◽  
Weight Ratio ◽  
High Strength ◽  
Design Parameters ◽  
Leaf Spring ◽  
Metallic Structures ◽  
Conventional Steel ◽  
Fiberglass Composite

In these paper, composite structures for conventional metallic structures has many advantages because of higher specific stiffness and strength of composite materials is discussed. The automobile industry has shown increased interest in the replacement of steel spring with fiberglass composite leaf spring due to high strength to weight ratio. This work deals with the replacement of conventional steel leaf spring with a Mono Composite leaf spring using E-Glass/Epoxy. The design parameters were selected and analyzed with the objective of minimizing weight of the composite leaf spring as compar

Properties and Performance Analysis of Woven Roving Composite Laminates for Automotive Panel Board Applications

2013 ◽  
Vol 683 ◽  
pp. 21-24 ◽  
Author(s):  
Raja R. Niranjan ◽  
S. Junaid Kokan ◽  
R. Sathya Narayanan ◽  
S. Rajesh ◽  
C. Elanchezhian ◽  
...  
Keyword(s):  
Circular Hole ◽  
Composite Laminates ◽  
Natural Fibers ◽  
Weight Ratio ◽  
High Strength ◽  
Filament Winding ◽  
Central Hole ◽  
Rectangular Hole ◽  
Low Thermal Expansion ◽  
Automotive Panel

Now-a-days natural Fibers are employed in various engineering applications because of their high tensile strength, low thermal expansion, high strength to weight ratio and good corrosion resistance. In this paper, woven roving composite laminates are prepared to produce automotive panel boards. Even though, various methods are available for preparing composites like Pultrusion method, filament winding method and hand layup method, hand lay method is used in this paper. The bundles of woven roving are alkalized at concentration between 1.2 and 6% of NaoH. Then, the treated fibres with increased strength are used as reinforcement with Epoxy LY556 resin with HY951 hardener under room temperature. The tensile analysis is conducted for the specimens like plain specimen, specimen with circular central hole and specimen with rectangular central hole. The results show that plain specimen is having more strength followed by circular hole and then rectangular hole specimens. It suggested that the case industry can make near optimal circular hole for its components by replacing rectangular hole.

scholarly journals A Review on Comparative Analysis of Leaf Spring by Using Different Variable Materials

IJOSTHE ◽  
2020 ◽  
Vol 7 (2) ◽  
pp. 1-5
Author(s):  
Abhishek Jha ◽  
Dr. Rashmi Dwivedi
Keyword(s):  
Composite Materials ◽  
Automobile Industry ◽  
Weight Ratio ◽  
High Strength ◽  
Design Parameters ◽  
Leaf Spring ◽  
Modern World ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced

Reducing weight while increasing or maintaining strength of products is getting to be highly important research issue in this modern world. Composite materials are one of the material families which are attracting researchers and being solutions of such issue. In this paper we describe design and analysis of polymer composite leaf spring. The objective is to compare the stresses, deformations and weight saving of composite leaf spring with that of steel leaf spring. The Automobile Industry has great interest for replacement of steel leaf spring with that of composite leaf spring, since the composite materials has high strength to weight ratio and good corrosion resistance. The material selected was glass fibre reinforced polymer (E-glass/epoxy) and is used against conventional steel. The design parameters can be selected and analysed with the objective of minimizing weight of the composite leaf spring as compared to the steel leaf spring.

Bamboo Waste-based Bio-composite Substance: An application for Low-cost Construction Materials

2020 ◽  
Vol 4 (1) ◽  
pp. 41-48
Author(s):  
Teodoro Astorga Amatosa ◽  
Michael E. Loretero
Keyword(s):  
Composite Materials ◽  
Sea Water ◽  
Raw Materials ◽  
Low Cost ◽  
Construction Materials ◽  
Single Layer ◽  
High Strength ◽  
Green Technology ◽  
Experimental Medium ◽  
Natural Treatment

Bamboo is a lightweight and high-strength raw materials that encouraged researchers to investigate and explore, especially in the field of biocomposite and declared as one of the green-technology on the environment as fully accountable as eco-products. This research was to assess the technical feasibility of making single-layer experimental Medium-Density Particleboard panels from the bamboo waste of a three-year-old (Dendrocalamus asper). Waste materials were performed to produce composite materials using epoxy resin (C21H25C105) from a natural treatment by soaking with an average of pH 7.6 level of sea-water. Three different types of MDP produced, i.e., bamboo waste strip MDP (SMDP), bamboo waste chips MDP (CMDP) and bamboo waste mixed strip-chips MDP (MMDP) by following the same process. The experimental panels tested for their physical-mechanical properties according to the procedures defined by ASTM D1037-12. Conclusively, even the present study shows properties of MDP with higher and comparable to other composite materials; further research must be given better attention as potential substitute to be used as hardwood materials, especially in the production, design, and construction usage.

Investigation of the Mechanical Behavior of Natural Vegetable Fibers Used in Composite Materials for Structural Strengthening

2021 ◽  
Vol 888 ◽  
pp. 15-21
Author(s):  
Ivelina Ivanova ◽  
Jules Assih ◽  
Dimitar Dontchev
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Fiber Composite ◽  
Low Cost ◽  
Weight Ratio ◽  
Synthetic Fiber ◽  
Engineering Structures ◽  
Hemp Fiber ◽  
Plant Fibers ◽  
Hemp Fibers

This research aims at studying the mechanical properties of industrial hemp fibers and promoting their use as a reinforcing composite material for strengthening of civil engineering structures. Natural hemp fibers are of great interest due to the following advantages they have: low cost, high strength-to-weight ratio, low density and non-corrosive properties. The use of plant fiber composite materials has increased significantly in recent years because of the negative reduction impact on the environment. For example, the tendency to use renewable resources and their possibility for recycling. They cause fewer health and environmental problems than synthetic fibers. Natural fibers, in addition to environmental aspects, have advantages such as low densities, i.e. have low weight, interesting mechanical properties comparable to those of synthetic fiber materials, and last but not least, low cost. Composites based on natural plant fibers can be used to reinforce or repair reinforced concrete structures, as shown by research on flax fiber composites. These concretes specimens strengthened with biocomposite materials have very good resistance to bending and significantly increase the rigidity of the structure. The results show that the hemp fiber reinforcement has significant effects on the strengthening and increase in flexural strength from 8% to 35 %.

scholarly journals Effect of reinforcements on polymer matrix bio-composites – an overview

2018 ◽  
Vol 25 (6) ◽  
pp. 1039-1058 ◽  
Author(s):  
Sumit Das Lala ◽  
Ashish B. Deoghare ◽  
Sushovan Chatterjee
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Natural Fibers ◽  
High Strength ◽  
Low Density ◽  
Intrinsic Properties ◽  
Environment Friendly ◽  
Complex Shapes ◽  
Strength And Durability ◽  
Comprehensive Study

AbstractThe inherent properties of bio-composites such as biodegradability, environment friendly, low cost of production, high strength and durability make them a suitable replacement to traditional materials such as glass and nylon. Bio-polymers are finding wide applications due to their intrinsic properties such as low density, low thermal conductivity, corrosion resistance and ease of manufacturing complex shapes. This paper aims toward a comprehensive study on polymer bio-composites. The review mainly focuses on types of reinforcements such as natural fibers, seed shells, animal fibers, cellulose, bio-polymers, bio-chemicals and bioceramics which enhance the mechanical properties, such as tensile strength, compressive strength, flexural strength, Young’s modulus and creep behavior, of the composites. The pertinent study carried out in this review explores an enormous potentiality of the composites toward a wide variety of applications.

A Review on Development and Properties of GLARE, an Advanced Aircraft Material

2014 ◽  
Vol 618 ◽  
pp. 140-145
Author(s):  
Yang Liu ◽  
Ren Zhang ◽  
En Quan Liang ◽  
Dong Li ◽  
Ying Chen ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Composite Materials ◽  
Low Cost ◽  
High Strength ◽  
Aviation Industry ◽  
Conventional Aluminum Alloy ◽  
Civil Aircraft ◽  
Aircraft Material ◽  
History Of ◽  
New Generation

The history of GLARE laminate was introduced. Through comparison with conventional aluminum alloy sheets, the excellent performance of GLARE as a new generation aeronautic material is discussed. The properties and application of GLARE in large civil aircraft indicates that new composite materials such as GLARE will replace bulk aluminum alloy in future aircraft structure. With the continuous development of material technologies, a trend of developing high strength and low cost composite materials will lead aviation industry to a new stage.

Impact of the Harsh Environment on E-Glass Epoxy Composite

2019 ◽  
Author(s):  
Amir Hussain Idrisi ◽  
Abdel-Hamid Ismail Mourad ◽  
Beckry Abdel-Magid ◽  
Mohammad Mozumder ◽  
Yaser Afifi
Keyword(s):  
High Temperature ◽  
Composite Materials ◽  
Oil And Gas ◽  
Epoxy Composite ◽  
Uv Light ◽  
Weight Ratio ◽  
High Strength ◽  
Industrial Applications ◽  
Harsh Environment ◽  
Sustained Loads

Abstract Composite materials are being used in many industrial applications such as automobile, aerospace, marine, oil and gas industries due to their high strength to weight ratio. The long-term effect of sustained loads and environmental factors that include exposure to UV light, temperature, and moisture have been under investigation by many researchers. The major objective of this study is to evaluate the effects of harsh environment (e.g. seawater and high temperature) on the structural properties of E-glass epoxy composite materials. These effects were studied in terms of seawater absorption, permeation of salt and contaminants, chemical and physical bonds at the interface and degradation in mechanical properties. Samples were immersed in seawater at room temperature (23°C), 65°C and 90°C for the duration of 6 months. Results show that seawater absorption increased with immersion time at 23°C and 65°C, whereas the weight of the specimens decreased at 90°C. The moisture causes swelling at 23°C and 65°C and breakdown of chemical bonds between fiber and matrix at 90°C. It is observed that high temperature accelerates the degradation of the E-glass epoxy composite. At 90°C, the tensile strength of E-glass epoxy sharply decreased by 72.92% but no significant change was observed in modulus of elasticity of the composite.

scholarly journals Assessment of Mechanical Properties of Biocomposite Material by using Sawdust and Rice Husk

2019 ◽  
Vol 11 (3) ◽  
pp. 147-156
Author(s):  
Prabhat SINGH ◽  
Bhagel SINGH
Keyword(s):  
Rice Husk ◽  
Low Cost ◽  
Glass Fibers ◽  
Testing Machine ◽  
Weight Ratio ◽  
High Strength ◽  
Light Weight ◽  
Universal Testing ◽  
Biocomposite Material ◽  
Main Factor

This paper presents an experimental study on the development of biocomposite material by using sawdust (SD) and rice husk (RH). The use of composite in the present production has increased dramatically since the 1970’s. Traditional material like aluminum, steel, iron and copper etc. may be easily replaced by using this classical biocomposites. The tensile test, hardness and tear resistance test were conducted in a Universal testing machine as per ASTM D638, ASTM D2240 and ASTM D1004 standard, respectively. Although commercial industries have increasingly been concerned with the low cost, light weight and eco-friendly material, the biocomposite material has also a great potential for reduced production cost and low maintenance which have proven to be a main factor in a push towards recycled biocomposites. In this paper we have fabricated a biocomposite model from materials like sawdust, rice husk. The main reason to use biocomposites is that they are more economical and have high strength to weight ratio compared to glass fibers. Hence fabricated material can be used for various applications.

Sign in / Sign up

Export Citation Format

Share Document