scholarly journals Suitability of Muli Bamboo (Melocanna baccifera) for Making Bamboo Mat Plywood

1970 ◽  
Vol 46 (4) ◽  
pp. 543-548 ◽  
Author(s):  
M Ashaduzzaman ◽  
R Rana ◽  
MNH Khan ◽  
MI Shams
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Average Density ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Formaldehyde Resin ◽  
Alternative Source

This paper investigated the potentiality of muli (Melocanna baccifera) for making bamboo mat plywood. Bamboo mat plywood with the length, width and thickness of 2.4 m × 1.2 m × 7 mm was made using liquid urea formaldehyde resin. The physical and mechanical properties of such plywood were compared with the existing market plywood. The average density of bamboo mat plywood was much higher compared to the existing market plywood. The modulus of rupture (MOR) of bamboo mat plywood was 3 times and the modulus of elasticity (MOE) was 6 times higher compared to commercial (Bombax ceiba) plywood. Interestingly, the specific MOR and MOE were significantly higher than those of market plywood. The high strength values might be due to the long fiber length of the bamboo. Furthermore, the lamination of decorative thin garjan (Dipterocarpus turbinatus) veneer did not significantly reduce mechanical properties of the products. Bamboo plywood mat as well as garjan laminated bamboo mat plywood showed better performance in respect to thickness swelling, linear expansion and water absorption. Hence, muli bamboo can be a potential alternative source of raw material for the manufacture of plywood materials. Key words: Bamboo mat plywood; Density; Dimensional stability; Modulus of elasticity; Modulus of rupture DOI: http://dx.doi.org/10.3329/bjsir.v46i4.9605 BJSIR 2011; 46(4): 543-548

scholarly journals Influence of Board Density on the Physical and Mechanical Properties of Bamboo Oriented Strand Lumber

Forests ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 567 ◽  
Author(s):  
Yuhui Sun ◽  
Yahui Zhang ◽  
Yuxiang Huang ◽  
Xiaoxin Wei ◽  
Wenji Yu
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Physical And Mechanical Properties ◽  
Basic Research ◽  
High Strength ◽  
Density Variation ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Board Density ◽  
Property Control

The process of bamboo-oriented strand lumber (BOSL) represents one of the best opportunities for automation, property control and consistency, and high utilization of material from abundant, fast-growing, and sustainable bamboo. In this study, BOSLs were prepared, with reference to the preparation process of bamboo scrimber, by compressing and densifying constituent units under the action of moisture-heat-force and resin polymerization, and then the effects of density variation on their physical and mechanical properties were investigated. The results revealed that the modulus of rupture, modulus of elasticity, compressive strength and shear strength of BOSL with density of 0.78–1.3 g/cm3 ranged from 124.42 to 163.2 MPa, 15,455 to 21,849 MPa, 65.02 to 111.63 MPa, and 9.88 to 18.35 MPa, respectively. The preparation of BOSL with bamboo as raw material could retain the good mechanical properties of natural bamboo, and produce bamboo-based structural products with different properties by controlling the density. The high strength of BOSL with high density was primarily due to the increased volume fraction of elementary fibers, the reduced porosity, and the enhanced gluing interface. The performance of BOSL can be comparable to, or surpass that of, wood or bamboo products. This study provided necessary basic research for the engineering design and application of BOSL.

scholarly journals Evaluation of the physical and mechanical properties of particleboard made from giant reed (Arundo donax L.)

BioResources ◽  
2010 ◽  
Vol 6 (1) ◽  
pp. 477-486
Author(s):  
Teresa García-Ortuño ◽  
Javier Andréu-Rodríguez ◽  
María T. Ferrández-García ◽  
Manuel Ferrández-Villena ◽  
Clara E. Ferrández-García
Keyword(s):  
Mechanical Properties ◽  
Urea Formaldehyde ◽  
Single Layer ◽  
Physical And Mechanical Properties ◽  
Arundo Donax ◽  
Modulus Of Rupture ◽  
Giant Reed ◽  
Formaldehyde Resin ◽  
Thickness Swelling ◽  
Arundo Donax L

Single-layer experimental particleboards were made from various sizes of Arundo donax particles bonded with urea formaldehyde resin. The experimental panels were tested for their mechanical strength including modulus of rupture (MOR), modulus of elasticity (MOE), internal bonding (IB), screw holding strength (SH), and physical properties (density, moisture content, thickness swelling (TS), and water absorption (WA)) according to the procedures defined by European Union (EN) Standards. The overall results showed that most panels exceeded the EN Standards for MOE, MOR, and IB. The mechanical properties of the particleboard were enhanced as the density increased. Particle size was found to have a profound effect on the board properties.

scholarly journals Effect of Graphene Oxide Nanoparticles on the Physical and Mechanical Properties of Medium Density Fiberboard

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1818
Author(s):  
Waheed Gul ◽  
Hussein Alrobei
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Urea Formaldehyde ◽  
Medium Density Fiberboard ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Formaldehyde Resin ◽  
Oxide Nanoparticles ◽  
Medium Density ◽  
Thickness Swelling

In this research, the special effects of graphene oxide nanoparticle charging (0, 2, 4, 6, wt.%) on the properties of medium-density fiberboard were examined. Physical and mechanical properties of the panels were determined conferring the method of European Norm standards. The consequences exhibited substantial enhancement in mechanical properties, explicitly in modulus of rupture, modulus of elasticity and internal bonding for 2–6% nanoparticle addition in a urea–formaldehyde resin. The mechanical properties, i.e., internal bond, modulus of elasticity and modulus of rupture were improved by 28.5%, 19.22% and 38.8%, respectively. Results also show a clear enhancement in thickness swelling and water absorption. The physical properties of thickness swelling, water absorption and thermal conductivity were improved up to 50%, 19.5% and 39.79%, respectively. The addition of graphene oxide nanoparticles strongly affected the curing time of the urea–formaldehyde resin and improved its thermal stability.

scholarly journals Physical and Mechanical Properties of Engineered Coconut Trunk Veneer (ECTV) for Interior Products

CORD ◽  
2013 ◽  
Vol 29 (1) ◽  
pp. 4
Author(s):  
Izran K.
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Cocos Nucifera ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Modulus Of Rupture ◽  
Uf Resin ◽  
Mixed Layers ◽  
Different Parts

A study was undertaken to investigate the physical and mechanical properties of engineered coconut (Cocos nucifera) veneer (ECTV). The coconut trunks (40 – 50 years old) were obtained from Hutan Melintang, Perak and were peeled into veneers at Bestgrade Sdn. Bhd. The veneers were obtained from two different parts of coconut trunks viz inner and outer which were used to fabricate 5-ply engineered coconut veneers. The ECTVs were fabricated at FRIM’s Bio-Composite Laboratory. They were manufactured with urea formaldehyde (UF) resin and with three combinations namely 100% inner, 100% outer and alternate outer & inner veneers (mix). The densities for the engineered veneers made of 100% outer, 100% inner, and mixed layers were 944.1 kg/m3, 858.15 kg/m3 and 891.11 kg/m3, respectively. Results showed that the Modulus of Rupture (MOR) of the ECTV made from 100% outer veneers had the highest mean MOR value (88.69 MPa), followed by those made from the mixed veneers (74.35 MPa) and 100% inner (58.44 MPa), respectively.  On the other hand, the Modulus Of Elasticity (MOE) values were 10.12 Mpa for outer, 8,210 Mpa for inner and 10,075 Mpa for mixed. Overall, the testing results showed that the ECTV met the standard requirements.

Glutardialdehyde Modified Corn Starch – Urea Formaldehyde Resin as a Binder for Particleboard Making

2015 ◽  
Vol 754-755 ◽  
pp. 89-93 ◽  
Author(s):  
M.H.M. Amini ◽  
R. Hashim ◽  
N.S. Sulaiman ◽  
S. Hiziroglu ◽  
Othman Sulaiman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elasticity Modulus ◽  
Corn Starch ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Urea Formaldehyde Resin ◽  
Modulus Of Rupture ◽  
Formaldehyde Resin ◽  
Japanese Industrial Standard ◽  
Internal Bonding Strength

The objective of the study was to characterize and to evaluate physical and mechanical properties of experimental particleboard panels made from rubberwood (Heveabrasiliensis) using modified starch-urea formaldehyde as binder. Panels were manufactured using 13% corn starch modified with glutardialdehyde with addition of 2 % urea formaldehyde resin and tested for their physical and mechanical properties. All of the particleboards satisfied the Japanese Industrial Standard which required 2000 N/mm2, 8.0 N/mm2and 0.15 N/mm2for modulus of elasticity, modulus of rupture and internal bonding strength, respectively. The mechanical properties were comparable to those made using 15 % urea formaldehyde resin with reduction of formaldehyde fume was over 50 %.

scholarly journals Particleboards from Recycled Thermally Modified Wood

Forests ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1462
Author(s):  
Ján Iždinský ◽  
Zuzana Vidholdová ◽  
Ladislav Reinprecht
Keyword(s):  
Mechanical Properties ◽  
Urea Formaldehyde ◽  
Brown Rot ◽  
Decay Resistance ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Negative Effect ◽  
Serpula Lacrymans ◽  
Thermally Modified Wood ◽  
Modified Wood

In recent years, the production and consumption of thermally modified wood (TMW) has been increasing. Offcuts and other waste generated during TMWs processing into products, as well as already disposed products based on TMWs can be an input recycled raw material for production of particleboards (PBs). In a laboratory, 16 mm thick 3-layer PBs bonded with urea-formaldehyde (UF) resin were produced at 5.8 MPa, 240 °C and 8 s pressing factor. In PBs, the particles from fresh spruce wood and mixed particles from offcuts of pine, beech, and ash TMWs were combined in weight ratios of 100:0, 80:20, 50:50 and 0:100. Thickness swelling (TS) and water absorption (WA) of PBs decreased with increased portion of TMW particles, i.e., TS after 24 h maximally about 72.3% and WA after 24 h maximally about 64%. However, mechanical properties of PBs worsened proportionally with a higher content of recycled TMW—apparently, the modulus of rupture (MOR) up to 55.5% and internal bond (IB) up to 46.2%, while negative effect of TMW particles on the modulus of elasticity (MOE) was milder. Decay resistance of PBs to the brown-rot fungus Serpula lacrymans (Schumacher ex Fries) S.F.Gray increased if they contained TMW particles, maximally about 45%, while the mould resistance of PBs containing TMW particles improved only in the first days of test. In summary, the recycled TMW particles can improve the decay and water resistance of PBs exposed to higher humidity environment. However, worsening of their mechanical properties could appear, as well.

scholarly journals Mechanical Properties of Commercial Particleboard from Rubberwood (Hevea Brasiliensis) and Recycle Mix-Tropical Wood with Different Board Density

2021 ◽  
Vol 3 (1) ◽  
pp. 41-44
Author(s):  
Nur Wafa Amalina Amali ◽  
Nor Yuziah Mohd Yunus ◽  
Wan Mohd Nazri Wan Abdul Rahman
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Hevea Brasiliensis ◽  
Urea Formaldehyde ◽  
Wood Particle ◽  
Modulus Of Rupture ◽  
Internal Bonding ◽  
Board Density ◽  
Tropical Wood ◽  
Minimum Requirements

In this study, mechanical properties of commercially manufactured hybrid particleboard from mix-tropical wood and rubberwood with four different densities at 25mm thickness have been investigated. The particleboard sample cutting and testing was in accordance to EN312:2013. The density of particleboard is identified with interval of 10kg/m3 for different densities which include 660kg/m3, 670kg/m3, 680kg/m3 and 690kg/m3. Particleboards were made with the ratio of 40:60 for mix-tropical wood particle and rubberwood particle respectively. The particleboards were prepared with urea formaldehyde (UF) with E1 formulation with addition of wax and hardener.  Increment of 10kg/m3 density for each particleboard led to increase in internal bonding (IB), bending testing include modulus of rupture (MOR) and modulus of elasticity (MOE), surface soundness (SS) and screw edge (SE) withdrawal. It was found that with board increment of 10kg/m3, the improvement was not statically significant except that for MOR. All panels met the minimum requirements of standard.

scholarly journals Physical and Mechanical Properties of Binderless Particleboard Made from Steam-Pretreated Oil Palm Trunk Particles

2019 ◽  
Vol 3 (2) ◽  
pp. 46 ◽  
Author(s):  
Jia Geng Boon ◽  
Rokiah Hashim ◽  
Mohammed Danish ◽  
Wan Noor Aidawati Wan Nadhari
Keyword(s):  
Mechanical Properties ◽  
Oil Palm ◽  
Chemical Constituents ◽  
Starch Content ◽  
Urea Formaldehyde ◽  
Health And Safety ◽  
Physical And Mechanical Properties ◽  
Steam Pretreatment ◽  
Formaldehyde Resin ◽  
Oil Palm Trunk

Formaldehyde emissions from conventional particleboards raise issues of health and safety. One of the potential solutions is binderless particleboards made without using synthetic adhesives. However, the physical and mechanical properties of untreated binderless particleboards are relatively poor compared to conventional particleboards. This research aims to reveal the potential of using steam pretreatment to improve binderless particleboard properties made from oil palm trunk. The oil palm trunk particles were treated with steam pretreatment for different durations of time (20, 40, 60 min). The chemical constituents of the treated and untreated particles were evaluated. The binderless particleboards were made from treated and untreated particles. In addition, panels using untreated oil palm trunk particles with 10% urea–formaldehyde resin were made and used as a comparison. The boards were evaluated according to European Standards. The results indicated that the hemicellulose and starch content gradually reduced with the progression of steam pretreatment. The physical and mechanical properties were improved by increasing steam pretreatment duration. The steam pretreatment was able to improve the properties of binderless particleboards made from oil palm trunk. However, the performance of steam-pretreated binderless particleboard in this study is not compatible with the particleboards made using 10% urea–formaldehyde.

scholarly journals Analysis Physical and Mechanical Of Particle Boards Raw Materials Nipah Fruit Fiber

Teknomekanik ◽  
2019 ◽  
Vol 2 (1) ◽  
pp. 14-19
Author(s):  
M Saddikin ◽  
Hendri Nurdin ◽  
Primawati Primawati
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Average Density ◽  
Raw Material ◽  
Average Moisture Content ◽  
Particle Board ◽  
Wood Particles ◽  
Tapioca Flour

The raw materials of the timber industry, especially furniture, are increasingly difficult to obtain in the quantity and quality needed. The development efforts carried out were utilizing Nipah coir waste as a raw material for making particle boards. Particle boards are panel boards made of wood particles or materials containing lignocellulose. Nipah plants contain 27.3% lignin and 36.5% cellulose which has the potential to be used as raw material for particleboard production. This study aims to reveal the physical and mechanical properties of particleboards made from Nipah fruit fibre with adhesive using tapioca flour. The making of particle board is done with a ratio of 90%: 10%, 80%: 20%, 70%: 30%, 60%: 40%, by giving a pressure of 100 kg / cm2. Particle testing is carried out according to the JIS A 5908 standard (2003). From this study, the optimum results were obtained in variations of 60%:40%. The particle physical properties which have an average density value of 1.15 gr / cm3 and an average moisture content of 5.8%. While the mechanical properties obtained by the value of Modulus of Elasticity an average of 21,188.93 kg / cm2. This shows the particle board variations of 60%: 40% produced to meet the JIS A 5908 (2003) standard. Based on the analysis of the quality variations 60%: 40% of particle boards can be recommended as raw materials for interior furniture.

Sign in / Sign up

Export Citation Format

Share Document