scholarly journals Powerful Electron-Transfer Screen-Printed Platforms as Biosensing Tools: The Case of Uric Acid Biosensor

Biosensors ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 2
Author(s):  
Rocco Cancelliere ◽  
Alessio Di Tinno ◽  
Antonino Cataldo ◽  
Stefano Bellucci ◽  
Laura Micheli
Keyword(s):  
Electron Transfer ◽  
Uric Acid ◽  
Carbon Nanomaterials ◽  
Point Of Care ◽  
High Sensitivity ◽  
Transfer Constant ◽  
Peak Separation ◽  
Depth Study ◽  
Good Repeatability ◽  
Screen Printed

The use of carbon nanomaterials (CNMs) in sensors and biosensor realization is one of the hottest topics today in analytical chemistry. In this work, a comparative in-depth study, exploiting different nanomaterial (MWNT-CO2H, -NH2, -OH and GNP) modified screen-printed electrodes (SPEs), is reported. In particular, the sensitivity, the heterogeneous electron transfer constant (k0), and the peak-to-peak separation (ΔE) have been calculated and analyzed. After which, an electrochemical amperometric sensor capable of determining uric acid (UA), based on the nano-modified platforms previously characterized, is presented. The disposable UA biosensor, fabricated modifying working electrode (WE) with Prussian Blue (PB), carbon nanotubes, and uricase enzyme, showed remarkable analytical performances toward UA with high sensitivity (CO2H 418 μA μM−1 cm−2 and bare SPE-based biosensor, 33 μA μM−1 cm−2), low detection limits (CO2H 0.5 nM and bare SPE-based biosensors, 280 nM), and good repeatability (CO2H and bare SPE-based biosensors, 5% and 10%, respectively). Moreover, the reproducibility (RSD%) of these platforms in tests conducted for UA determination in buffer and urine samples results are equal to 6% and 15%, respectively. These results demonstrate that the nanoengineered electrode exhibited good selectivity and sensitivity toward UA even in the presence of interfering species, thus paving the way for its application in other bio-fluids such as simple point-of-care (POC) devices.

Nanocomposite based on restacked crystallites of β-NiS and Ppy for the determination of theophylline and uric acid on screen-printed electrodes

2019 ◽  
Vol 43 (48) ◽  
pp. 19397-19407
Author(s):  
P. Muthukumaran ◽  
R. Ramya ◽  
P. Thivya ◽  
J. Wilson ◽  
G. Ravi
Keyword(s):  
Uric Acid ◽  
Electrocatalytic Activity ◽  
High Sensitivity ◽  
Screen Printed Electrodes ◽  
Screen Printed

We synthesized calcinated β-NiS with a highly crystalline porous nature and mixed it with Ppy to prepare a nanocomposite, which exhibited high electrocatalytic activity and this was then used to detect theophylline and uric acid with high sensitivity and stability.

Computationally Assisted Design of High Signal-to-Noise Photoinduced Electron Transfer-Based Voltage-Sensitive Dyes

2020 ◽  
Author(s):  
Rishikesh Kulkarni ◽  
Anneliese Gest ◽  
Chun Kei Lam ◽  
Benjamin Raliski ◽  
Feroz James ◽  
...  
Keyword(s):  
Electron Transfer ◽  
Dft Calculations ◽  
Photoinduced Electron Transfer ◽  
Density Functional ◽  
Embryonic Stem ◽  
High Sensitivity ◽  
Md Simulations ◽  
High Signal ◽  
Signal To Noise ◽  
Green Fluorescent

<p>High signal-to-noise optical voltage indicators will enable simultaneous interrogation of membrane potential in large ensembles of neurons. However, design principles for voltage sensors with high sensitivity and brightness remain elusive, limiting the applicability of voltage imaging. In this paper, we use molecular dynamics (MD) simulations and density functional theory (DFT) calculations to guide the design of a bright and sensitive green-fluorescent voltage-sensitive fluorophore, or VoltageFluor (VF dye), that uses photoinduced electron transfer (PeT) as a voltage-sensing mechanism. MD simulations predict an 11% increase in sensitivity due to membrane orientation, while DFT calculations predict an increase in fluorescence quantum yield, but a decrease in sensitivity due to a decrease in rate of PeT. We confirm these predictions by synthesizing a new VF dye and demonstrating that it displays the expected improvements by doubling the brightness and retaining similar sensitivity to prior VF dyes. Combining theoretical predictions and experimental validation has resulted in the synthesis of the highest signal-to-noise green VF dye to date. We use this new voltage indicator to monitor the electrophysiological maturation of human embryonic stem cell-derived medium spiny neurons. </p>

Novel High Sensitivity Tuberculosis Point-of-Care Test for People Living with HIV

2018 ◽  
Author(s):  
Tobias Broger ◽  
Bianca Sossen ◽  
Elloise du Toit ◽  
Andrew D. Kerkhoff ◽  
Charlotte Schutz ◽  
...  
Keyword(s):  
Point Of Care ◽  
High Sensitivity ◽  
People Living With Hiv ◽  
Point Of Care Test ◽  
Living With Hiv

Trends in Diagnosis for Active Tuberculosis Using Nanomaterials

2019 ◽  
Vol 26 (11) ◽  
pp. 1946-1959 ◽  
Author(s):  
Le Minh Tu Phan ◽  
Lemma Teshome Tufa ◽  
Hwa-Jung Kim ◽  
Jaebeom Lee ◽  
Tae Jung Park
Keyword(s):  
Sensitivity And Specificity ◽  
High Efficiency ◽  
Point Of Care ◽  
High Sensitivity ◽  
Signs And Symptoms ◽  
Diagnostic Methods ◽  
Advantages And Disadvantages ◽  
Treatment And Prevention ◽  
Clinical Tools ◽  
Diagnostic Applications

Background:Tuberculosis (TB), one of the leading causes of death worldwide, is difficult to diagnose based only on signs and symptoms. Methods for TB detection are continuously being researched to design novel effective clinical tools for the diagnosis of TB.Objective:This article reviews the methods to diagnose TB at the latent and active stages and to recognize prospective TB diagnostic methods based on nanomaterials.Methods:The current methods for TB diagnosis were reviewed by evaluating their advantages and disadvantages. Furthermore, the trends in TB detection using nanomaterials were discussed regarding their performance capacity for clinical diagnostic applications.Results:Current methods such as microscopy, culture, and tuberculin skin test are still being employed to diagnose TB, however, a highly sensitive point of care tool without false results is still needed. The utilization of nanomaterials to detect the specific TB biomarkers with high sensitivity and specificity can provide a possible strategy to rapidly diagnose TB. Although it is challenging for nanodiagnostic platforms to be assessed in clinical trials, active TB diagnosis using nanomaterials is highly expected to achieve clinical significance for regular application. In addition, aspects and future directions in developing the high-efficiency tools to diagnose active TB using advanced nanomaterials are expounded.Conclusion:This review suggests that nanomaterials have high potential as rapid, costeffective tools to enhance the diagnostic sensitivity and specificity for the accurate diagnosis, treatment, and prevention of TB. Hence, portable nanobiosensors can be alternative effective tests to be exploited globally after clinical trial execution.

Facile and Fast Detection of Genistein in Derris scandens by Square Wave Voltammetry using a Cobalt(II) Phthalocyanine-Modified Screen-Printed Electrochemical Sensor

2020 ◽  
Vol 16 (3) ◽  
pp. 341-348
Author(s):  
Surinya Traipop ◽  
Suchada Chuanuwatanakul ◽  
Orawon Chailapakul ◽  
Eakkasit Punrat
Keyword(s):  
Electrochemical Sensor ◽  
Square Wave Voltammetry ◽  
Silver Chloride ◽  
Reference Electrode ◽  
High Sensitivity ◽  
Plastic Substrate ◽  
Fast Analysis ◽  
Square Wave ◽  
Wave Voltammetry ◽  
Screen Printed

Background: Recently, Derris scandens, a Thai herbal medicine with anti-inflammatory activity, is widely used as beverage and supplementary food. When the traditional medicine is a choice for health therapy, the simple and reliable equipment is required to control the suitable consuming amount of the active component. Objective: To develop the electrochemical sensor for genistein determination in Derris scandens with high sensitivity and rapid operation. Methods: An in-house screen-printed electrochemical sensor consisting of a three-electrode system was developed for genistein determination. A silver/silver chloride (Ag/AgCl) reference electrode, a carbon counter electrode and a carbon working electrode were prepared on a 0.3-mm-thick plastic substrate by the screen-printing technique using conductive ink. The dimensions of each sensor were 2.5×1.0 cm. Only 50 µL of sample solution was required on this device for the determination of genistein concentration by rapid response square wave voltammetry. Results: The oxidation peak of genistein appeared with good response in acidic media at a peak potential of 0.6 V. Moreover, the signal was enhanced by modifying the conductive carbon ink with cobalt( II) phthalocyanine. Under the optimized conditions, the linear range was found to be 2.5-150 µM and the detection limit was 1.5 µM. Moreover, the small volume extraction was successfully developed without any further pre-concentration. This proposed method was applied to determine genistein in Derris scandens with satisfying results. Conclusion: The proposed method is promising as an alternative method for genistein determination with facile and fast analysis.

scholarly journals A Rapid, High-Sensitivity SARS-CoV-2 Nucleocapsid Immunoassay to Aid Diagnosis of Acute COVID-19 at the Point of Care: A Clinical Performance Study

2021 ◽  
Author(s):  
Paul K. Drain ◽  
Madhavi Ampajwala ◽  
Christopher Chappel ◽  
Andre B. Gvozden ◽  
Melanie Hoppers ◽  
...  
Keyword(s):  
Clinical Performance ◽  
Point Of Care ◽  
High Sensitivity ◽  
Performance Study

scholarly journals Evaluation of Production Lots of a Rapid Point-of-Care Lateral Flow Serological Test Intended for Identification of IgM and IgG against the N-Terminal Part of the Spike Protein (S1) of SARS-CoV-2

Viruses ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 1043
Author(s):  
Tove Hoffman ◽  
Linda Kolstad ◽  
Bengt Rönnberg ◽  
Åke Lundkvist
Keyword(s):  
Predictive Value ◽  
Serological Test ◽  
Point Of Care ◽  
External Validation ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Spike Protein ◽  
Individual Level ◽  
Lateral Flow Test ◽  
Production Errors

The potential of rapid point-of-care (POC) tests has been subject of doubt due to an eventual risk of production errors. The aim was therefore to evaluate the two separate production lots of a commercial POC lateral flow test, intended for the detection of IgM and IgG against the SARS-CoV-2 spike protein (S1). Control samples consisted of serum from individuals with confirmed SARS-CoV-2 infection and pre-COVID-19 negative sera gathered from a biobank. The presence of anti-S1 IgM/IgG in the sera was verified by an in-house Luminex-based serological assay (COVID-19 SIA). One hundred samples were verified as positive for anti-S1 IgG and 74 for anti-S1 IgM. Two hundred samples were verified as negative for anti-S1 IgM/IgG. For the two lots of the POC-test, the sensitivities were 93.2% and 87.8% for IgM and 93.0% and 100% for IgG. The specificities were 100% for IgM and 99.5% for IgG. The positive predictive value was 100% for IgM and 98.9% and 99.0% for IgG. The negative predictive value was 97.6% and 95.7% for IgM, and 96.6% and 100% for IgG. The evaluated POC-test is suitable to assess anti-SARS-CoV-2 S1 IgM and IgG, as a measure of previous virus exposure on an individual level. The external validation of separate lots of rapid POC-tests is encouraged to ensure high sensitivity before market introduction.

Screen printed diamond electrode as efficient “point-of-care” platform for submicromolar determination of cytostatic drug in biological fluids and pharmaceutical product

2021 ◽  
Vol 113 ◽  
pp. 108277
Author(s):  
Dalibor M. Stanković ◽  
Zorana Milanović ◽  
Ľubomír Švorc ◽  
Vesna Stanković ◽  
Drina Janković ◽  
...  
Keyword(s):  
Biological Fluids ◽  
Point Of Care ◽  
Pharmaceutical Product ◽  
Cytostatic Drug ◽  
Efficient Point ◽  
Diamond Electrode ◽  
Screen Printed

scholarly journals Integrating high-performing electrochemical transducers in lateral flow assay

2021 ◽  
Author(s):  
Antonia Perju ◽  
Nongnoot Wongkaew
Keyword(s):  
High Performance ◽  
Point Of Care ◽  
Low Cost ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Analytical Performance ◽  
Label Free ◽  
High Performing ◽  
Lateral Flow Assays ◽  
Electrochemical Transducers

AbstractLateral flow assays (LFAs) are the best-performing and best-known point-of-care tests worldwide. Over the last decade, they have experienced an increasing interest by researchers towards improving their analytical performance while maintaining their robust assay platform. Commercially, visual and optical detection strategies dominate, but it is especially the research on integrating electrochemical (EC) approaches that may have a chance to significantly improve an LFA’s performance that is needed in order to detect analytes reliably at lower concentrations than currently possible. In fact, EC-LFAs offer advantages in terms of quantitative determination, low-cost, high sensitivity, and even simple, label-free strategies. Here, the various configurations of EC-LFAs published are summarized and critically evaluated. In short, most of them rely on applying conventional transducers, e.g., screen-printed electrode, to ensure reliability of the assay, and additional advances are afforded by the beneficial features of nanomaterials. It is predicted that these will be further implemented in EC-LFAs as high-performance transducers. Considering the low cost of point-of-care devices, it becomes even more important to also identify strategies that efficiently integrate nanomaterials into EC-LFAs in a high-throughput manner while maintaining their favorable analytical performance.

scholarly journals Ag nanoparticles outperform Au nanoparticles for the use as label in electrochemical point-of-care sensors

2021 ◽  
Author(s):  
Franziska Beck ◽  
Carina Horn ◽  
Antje J. Baeumner
Keyword(s):  
Limit Of Detection ◽  
Point Of Care ◽  
Automatic Measurement ◽  
High Sensitivity ◽  
Differential Pulse ◽  
Small Sample ◽  
Blood Protein ◽  
User Friendliness ◽  
Response Curves ◽  
Assay Protocol

AbstractElectrochemical immunosensors enable rapid analyte quantification in small sample volumes, and have been demonstrated to provide high sensitivity and selectivity, simple miniaturization, and easy sensor production strategies. As a point-of-care (POC) format, user-friendliness is equally important and most often not combinable with high sensitivity. As such, we demonstrate here that a sequence of metal oxidation and reduction, followed by stripping via differential pulse voltammetry (DPV), provides lowest limits of detection within a 2-min automatic measurement. In exchanging gold nanoparticles (AuNPs), which dominate in the development of POC sensors, with silver nanoparticles (AgNPs), not only better sensitivity was obtained, but more importantly, the assay protocol could be simplified to match POC requirements. Specifically, we studied both nanoparticles as reporter labels in a sandwich immunoassay with the blood protein biomarker NT-proBNP. For both kinds of nanoparticles, the dose-response curves easily covered the ng∙mL−1 range. The mean standard deviation of all measurements of 17% (n ≥ 4) and a limit of detection of 26 ng∙mL−1 were achieved using AuNPs, but their detection requires addition of HCl, which is impossible in a POC format. In contrast, since AgNPs are electrochemically less stable, they enabled a simplified assay protocol and provided even lower LODs of 4.0 ng∙mL−1 in buffer and 4.7 ng∙mL−1 in human serum while maintaining the same or even better assay reliability, storage stability, and easy antibody immobilization protocols. Thus, in direct comparison, AgNPs clearly outperform AuNPs in desirable POC electrochemical assays and should gain much more attention in the future development of such biosensors.

Sign in / Sign up

Export Citation Format

Share Document