scholarly journals Corner Separation Control Using a New Combined Slotted Configuration in a High-Turning Compressor Cascade under Different Solidities

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3376
Author(s):  
Hejian Wang ◽  
Yanshan Qing ◽  
Bo Liu ◽  
Xiaochen Mao
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Incidence Angle ◽  
Pressure Coefficient ◽  
Weight Ratio ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Turning Angle ◽  
Blade Loading ◽  
Corner Separation

In order to comprehensively control the corner separation and the blade trailing edge (TE) separation in a high-turning compressor stator cascade, this research proposes a new combined slotted configuration consisting of one full-span slot and two blade-end slots. Taking into account the effect of the blade solidity, the performance of the original cascade and the combined slotted cascade was calculated and evaluated in a wide incidence angle range at two blade solidities. The results indicated that the blade loading and the corner separation range of the original cascade becomes larger as the blade solidity decreases from 1.66 to 1.36, which leads to higher total pressure loss and lower pressure diffusing capacity under positive incidence angles. The low-momentum fluid in the boundary layer can be significantly re-energized by the high-momentum blade-end and full-span slots jets, hence the combined slotted configuration can eliminate the blade TE separation and reduce the corner separation remarkably in the full incidence angle range at the two blade solidities. By adopting the combined slotted configuration, the total pressure loss, turning angle and static pressure coefficient of the original cascade can be increased by −23.2%, 2.7° and 4.7% on average, respectively, when the blade solidity is 1.66, while they can be increased by −27.7%, 3.3° and 7.6% on average, respectively, when the blade solidity is 1.36. The combined slotted configuration has a significant adaptability to the low blade solidity (or high loading) condition and it shows a certain potential in increasing the aeroengine thrust-to-weight ratio by decreasing the compressor single-stage blade number.

Location Effect of Boundary Layer Suction on Compressor Hub-Corner Separation

2014 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Base Flow ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Corner Separation ◽  
Boundary Layer Suction

The large secondary flow area in the compressor hub-corner region usually leads to three-dimensional separation in the passage with large amounts of total pressure loss. In this paper numerical simulations of a linear high-speed compressor cascade, consisting of five NACA 65-K48 stator profiles, were performed to analyze the flow mechanism of hub-corner separation for the base flow. Experimental validation is used to verify the numerical results. Active control of the hub-corner separation was investigated by using boundary layer suction. The influence of the selected locations of the endwall suction slot was investigated in an effort to quantify the gains of the compressor cascade performance. The results show that the optimal chordwise location should contain the development section of the three-dimensional corner separation downstream of the 3D corner separation onset. The best pitchwise location should be close enough to the vanes’ suction surface. Therefore the optimal endwall suction location is the MTE slot, the one from 50% to 75% chord at the hub, close to the blade suction surface. By use of the MTE slot with 1% suction flow ratio, the total-pressure loss is substantially decreased by about 15.2% in the CFD calculations and 9.7% in the measurement at the design operating condition.

Flowfield Investigation of a Compressor Cascade at High Incidence—Part 1: Pneumatic Probe Measurements

2009 ◽  
Author(s):  
Pavlos K. Zachos ◽  
Vassilios Pachidis ◽  
Bernard Charnley ◽  
Pericles Pilidis
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Incidence Angle ◽  
Axial Flow ◽  
Quantitative Measure ◽  
Operating Conditions ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Engine Operation ◽  
Pressure Surface

The performance prediction of axial flow compressors and turbines still relies on the stationary testing of blade cascades. Most of the blade testing studies are done for operating conditions close to the design point or in off-design areas not too far from it. However, blade performance remains unexplored at very far off-design conditions, such as windmilling, characterised by operation under extremely low mass flows and rotational speeds which, in turn, imply highly negative incidence angle values. In this paper, the flow field generated by a 3-dimensional linear compressor cascade at a highly negative incidence angle and zero rotational speed is experimentally investigated using a pneumatic miniature cobra probe. The main objective of the study is to derive the total pressure loss through the blades at such a highly negative incidence angle. An overview of the blade geometry as well as of the experimental facility is given whereas the measurement strategy and the data acquisition technique are also presented. An uncertainty study taking into account the most significant factors affecting the quality of the results has been carried out. As shown by the measurements taken at specific positions downstream of the blades, the flowfield is dominated by highly separated flows on the pressure surface, which contribute to the increased values of the total pressure loss coefficient which seems to be weakly dependent on the inlet Mach number. The quantitative measure of the pressure losses at the extremely negative incidence angle examined can be considered to be a validation platform for correspondent numerical studies of similar flow conditions. Additionally, the experimental results obtained can be used to extend the applicability of the current pressure loss models, increasing the predictive capability of the through flow numerical approaches towards far off-design areas of component or whole engine operation.

Corner Separation Control in a Highly Loaded Compressor Cascade Using Plasma Aerodynamic Actuation

2012 ◽  
Author(s):  
Yun Wu ◽  
Xiao-hu Zhao ◽  
Ying-hong Li ◽  
Jun Li
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Separation Control ◽  
Compressor Cascade ◽  
Control Effect ◽  
Suction Surface ◽  
Corner Separation ◽  
Pressure Loss Coefficient ◽  
Highly Loaded

Corner separation, which forms over the suction surface and endwall corner of a blade passage, causes significant total pressure loss in highly loaded compressors. Plasma flow control, based on the plasma aerodynamic actuation, is a novel active flow control technique to improve aircrafts’ aerodynamic characteristics and propulsion efficiency. This paper reports computational and experimental results on using three types of plasma aerodynamic actuation (PAA) to control the corner separation in a highly loaded, low speed, linear compressor cascade. Reynolds-Averaged Navier-Stokes simulations were performed to optimize the PAA arrangement. The PAA was generated by a microsecond or nanosecond dielectric barrier discharge in wind tunnel experiments. The total pressure loss coefficient distribution was adopted to evaluate the corner separation control effect. The control effect of pitch-wise PAA on the endwall, in terms of relative reduction of the pitch-wise averaged total pressure loss coefficient in the wake, is much better than that of stream-wise PAA on the suction surface. When both pitch-wise PAA on the endwall and stream-wise PAA on the suction surface are turned on simultaneously, the control effect is the best among all three types of PAA. The main effect of pitch-wise PAA on the endwall is to inhibit the crossflow from neighboring pressure surface to the suction surface, whilest the main effect of stream-wise PAA on the suction surface is to inhibit the boundary layer accumulation and separation. Compared to microsecond discharge PAA, nanosecond discharge PAA is more effective at higher freestream velocity. The mechanisms for nanosecond discharge and microsecond discharge PAA are different for corner separation control.

Second Vane Total Pressure Loss Due to Endwall Iceform Contouring

2008 ◽  
Author(s):  
Ronald S. LaFleur
Keyword(s):  
Heat Transfer ◽  
Secondary Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Drag ◽  
Pressure Coefficient ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Surface Shape ◽  
Exit Plane

The iceformation design method generates an endwall contour, altering the secondary flows that produce elevated endwall heat transfer load and total pressure losses. Iceformation is an analog to regions of metal melting where a hot fluid alters the isothermal surface shape of a part as it is maintained by a cooling fluid. The passage flow, heat transfer and geometry evolve together under the constraints of flow and thermal boundary conditions. The iceformation concept is not media dependent and can be used in analogous flows and materials to evolve novel boundary shapes. In the past, this method has been shown to reduce aerodynamic drag and total pressure loss in flows such as diffusers and cylinder/endwall junctures. A prior paper [1] showed that the Reynolds number matched iceform geometry had a 24% lower average endwall heat transfer than the rotationally symmetric endwall geometry of the Energy Efficiency Engine (E3). Comparisons were made between three endwall geometries: the ‘iceform’, the ‘E3’ and the ‘flat’ as a limiting case of the endwall design space. This paper adds to the iceformation design record by reporting the endwall aerodynamic performances. Second vane exit flow velocities and pressures were measured using an automated 2-D traverse of a 1.2 mm diameter five-hole probe. Exit plane maps for the three endwall geometries are presented showing the details of the total pressure coefficient contours and the velocity vectors. The formation of secondary flow vortices is shown in the exit plane and this results in an impact on exit plane total pressure loss distribution, off-design over- and under-turning of the exit flow. The exit plane contours are integrated to form overall measures of the total pressure loss. Relative to the E3 endwall, the iceform endwall has a slightly higher total pressure loss attributed to higher dissipation of the secondary flow within the passage. The iceform endwall has a closer-to-design exit flow pattern than the E3 endwall.

Endwall Contouring and Fillet Design for Reducing Losses and Homogenizing the Outflow of a Compressor Cascade

2014 ◽  
Author(s):  
Oliver Reutter ◽  
Stefan Hemmert-Pottmann ◽  
Alexander Hergt ◽  
Eberhard Nicke
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Region ◽  
Optimized Design ◽  
Compressor Cascade ◽  
Outflow Region ◽  
Endwall Contouring ◽  
Operating Points

The following paper deals with the development of an optimized fillet and an endwall contour for reducing the total pressure loss and for homogenizing the outflow of a highly loaded cascade with a low aspect ratio. The NACA-65 K48 cascade profile without a fillet and without endwall contouring is used as a basis. Optimizations are performed using the DLR in-house tool AutoOpti and the RANS-solver TRACE. Three operating points at an inflow Mach number of 0.67 with different inflow angles are used to secure a wide operating range of the optimized design. At first only a fillet is optimized. The optimized fillet is small at the leading edge and rather high, wide and thick towards the trailing edge. It reduces the total pressure loss and homogenizes the outflow up to a blade height of 20 %. Following this a combined optimization of the endwall and the fillet is performed. The optimized contour leads to the development of a vortex, which changes the secondary flow in such a way, that the corner separation is reduced, which in turn significantly reduces the total pressure loss up to 16 % in the design operating point. The contour in the outflow region leads to a significant homogenization of the outflow in the near wall region.

A new curvature-controlled stacking-line method for optimization design of compressor cascade considering surface smoothness

2019 ◽  
Vol 234 (5) ◽  
pp. 1061-1074
Author(s):  
Xinyi Zhang ◽  
Xiaoqing Qiang ◽  
Jinfang Teng ◽  
Wensheng Yu
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Optimization Design ◽  
Parametric Method ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Surface Smoothness ◽  
Line Method ◽  
Radial Curvature ◽  
Bézier Spline

The paper presents an advanced parametric method of blade stacking lines in terms of sweep and lean based on controlled curvature. To the knowledge of the authors, there is no related approach reported in open literature that uses Bezier spline as the radial curvature distribution to improve the smoothness of the blade surface; most previous studies ignored the discontinuous slopes of curvature of the parametric curves. The parametric method called curvature-controlled stacking-line method (CCSLM) is performed by changing the magnitude of the sweep or lean. A fourth Bezier spline is adopted to define the curvature of spanwise stacking line directly ensuring surface smoothness. Then, the redesign cascades are created by sectional profiles stacked along the radial stacking lines which are obtained by twice integrating the Bezier spline. Then, the advanced method is conducted to optimize a high-subsonic controlled diffusion airfoil at design point, where the blade shape is generated in terms of lean. A single-objective optimization is performed using Kriging model and genetic algorithm to optimize total pressure loss, and the optimized geometry is obtained. The optimization results show that the blade design CCSLM has significant effects on the endwall flow vortex as well as radial loading distribution. The reduction of total pressure loss and secondary flow is also observed, and the aerodynamic performance is well improved compared with the original cascade.

Impact of a Combination of Micro-Vortex Generator and Boundary Layer Suction on Performance in a High-Load Compressor Cascade

2018 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Chuanle Liu
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Control Methods ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Micro Vortex Generator

The performance of a compressor cascade is considerably influenced by flow control methods. In this paper, the synergistic effects of combination between micro-vortex generators (MVG) and boundary layer suction (BLS) are discussed in a high-load compressor cascade. Seven cases, which are grouped by a kind of micro-vortex generator and boundary layer suction with three locations, are investigated to control secondary flow effects and enhance the aerodynamic performance of the compressor cascade. The MVG is mounted on the end-wall in front of the passage. The rectangle suction slot with three radial positions is installed on the blade suction surface near the trailing edge. The numerical results show that: at the design condition, the total pressure loss is effectively decreased as well as the static pressure coefficient increase when the combined MVG and SBL method (COM) is used, which is superior to MVG in an aerodynamic performance. At the stall condition, the induced vortex coming from MVG could mix the low-energy fluid and mainstream, which result in the reduced separation, and the total pressure loss decreased by 11.54% when the suction flow ratio is 1.5%. The total pressure loss decreases by 14.59% when the COM control methods are applied.

Investigation on Performance of Compressor Cascade with Tubercle Leading Edge Blade

2020 ◽  
Vol 37 (3) ◽  
pp. 295-303 ◽  
Author(s):  
Tu Baofeng ◽  
Zhang Kai ◽  
Hu Jun
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Large Scale ◽  
Design Method ◽  
Leading Edge ◽  
Experimental Tests ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Linear Compressor Cascade

AbstractIn order to improve compressor performance using a new design method, which originates from the fins on a humpback whale, experimental tests and numerical simulations were undertaken to investigate the influence of the tubercle leading edge on the aerodynamic performance of a linear compressor cascade with a NACA 65–010 airfoil. The results demonstrate that the tubercle leading edge can improve the aerodynamic performance of the cascade in the post-stall region by reducing total pressure loss, with a slight increase in total pressure loss in the pre-stall region. The tubercles on the leading edge of the blades cause the flow to migrate from the peak to the valley on the blade surface around the tubercle leading edge by the butterfly flow. The tubercle leading edge generates the vortices similar to those created by vortex generators, splitting the large-scale separation region into multiple smaller regions.

Secondary Flow Loss Reduction Through Blowing for a High-Lift Front-Loaded Low Pressure Turbine Cascade

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Stuart I. Benton ◽  
Jeffrey P. Bons ◽  
Rolf Sondergaard
Keyword(s):  
Reynolds Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Control Method ◽  
Low Pressure ◽  
Total Pressure Loss ◽  
Suction Surface ◽  
High Lift ◽  
Blade Loading ◽  
Low Pressure Turbine

Efforts to increase individual blade loading in the low pressure turbine have resulted in blade geometries optimized for midspan performance. Many researchers have shown that increased blade loading and a front-loaded pressure distribution each separately contribute to increased losses in the endwall region. A detailed investigation of the baseline endwall flow of the L2F profile, which is a high-lift front loaded profile, is performed. In-plane velocity vectors and total pressure loss maps are obtained in five planes oriented normal to the blade surface for three Reynolds numbers. A row of pitched and skewed jets are introduced near the endwall on the suction surface of the blade. The flow control method is evaluated for four momentum coefficients at the high Reynolds number, with a maximum reduction of 42% in the area averaged total pressure loss coefficient. The same blade is also fitted with midspan vortex-generator jets and is tested at a Reynolds number of 20,000, resulting in a 21% reduction in the area averaged total pressure loss.

scholarly journals Investigation of Wash Fluid Preheating on the Effectiveness of Online Compressor Washing in Industrial Gas Turbines

2020 ◽  
Author(s):  
Roupa Agbadede ◽  
Biweri Kainga
Keyword(s):  
Gas Turbines ◽  
Pressure Loss ◽  
Total Pressure ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Flow Angle ◽  
Pressure Loss Coefficient ◽  
Industrial Gas Turbines ◽  
Total Pressure Loss Coefficient

Abstract This study presents an investigation of wash fluid preheating on the effectiveness of online compressor washing in industrial gas turbines. Crude oil was uniformly applied on the compressor cascade blades surfaces using a roller brush, and carborundum particles were ingested into the tunnel to create accelerated fouled blades. Demineralized water was preheated to 500C using the heat coil provided in the tank. When fouled blades washed with preheated demineralized and the one without preheating were compared, it was observed that there was little or no difference in terms of total pressure loss coefficient and exit flow angle. However, when the fouled and washed cases were compared, there was a significant different in total pressure loss coefficient and exit flow angle.

Sign in / Sign up

Export Citation Format

Share Document