scholarly journals Performance of Cathodes Fabricated from Mixture of Active Materials Obtained from Recycled Lithium-Ion Batteries

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 410
Author(s):  
Hammad Al-Shammari ◽  
Siamak Farhad
Keyword(s):  
Lithium Ion Batteries ◽  
Active Material ◽  
Lithium Ion ◽  
Separation Process ◽  
The Other ◽  
Recycling Process ◽  
Active Materials ◽  
Actual Case ◽  
Voltage Level ◽  
The Difference

The cathode performance of lithium-ion batteries (LIBs) fabricated from recycled cathode active materials is studied for three scenarios. These scenarios are based on the conditions for separation of different cathode active materials in recycling facilities during the LIB’s recycling process. In scenario one, the separation process is performed ideally, and the obtained pure single cathode active material is used to make new LIBs after regeneration. In scenario two, the separation of active materials is performed with efficiencies of less than 100%, which is the actual case in the recycling process. In this scenario, a single cathode active material that contains a little of the other types of cathode active materials is used to make new LIBs after the materials’ regeneration. In scenario three, the separation has not been performed during the recycling process. In this scenario, all types of cathode active materials are regenerated together, and a mixture is used to make new LIBs. The studies are performed through modeling and computer simulation, and several experiments are conducted for validation purposes. The cathode active materials that are studied are the five commercially available cathodes made of LiMn2O4 (LMO), LiCoO2 (LCO), LiNixMnyCo(1−x−y)O2 (NMC), LiNixCoyAl(1−x−y)O2 (NCA), and LiFePO4 (LFP). The results indicate that the fabrication of new LIBs with a mixture of cathode active materials is possible when cathode active materials are not ideally separated from each other. However, it is recommended that the separation process is added to the recycling process, at least for the separation of LFP or reducing its amount in the cathode active materials mixture. This is because of the difference of the voltage level of LFP compared to the other studied active materials for cathodes.

Synthesis of Carbon-Added LiFePO4 Powders and Measurement of Charge-Discharge Properties

2013 ◽  
Vol 566 ◽  
pp. 91-94
Author(s):  
Takahiro Nakamura ◽  
Motofumi Yamada ◽  
Takayuki Kodera ◽  
Takashi Ogihara
Keyword(s):  
Lithium Ion Batteries ◽  
Active Material ◽  
Ultrasonic Spray Pyrolysis ◽  
Lithium Ion ◽  
Carbon Powder ◽  
Organic Substances ◽  
Active Materials ◽  
Ultrasonic Spray ◽  
Different Types ◽  
Charge Discharge

LiFePO4/C powders were synthesized by ultrasonic spray pyrolysis using carbon powder instead of organic substances as the carbon source. LiFePO4 (LFP) powders containing different types of carbon powders were prepared and used as cathode active materials in lithium ion batteries. The charge-discharge properties of lithium ion batteries with LFP, LFP/AB, and LFP/CNT powders as the cathode material were worse than those of the battery with LFP/sucrose powder as the cathode active material.

scholarly journals A Novel Pyrometallurgical Recycling Process for Lithium-Ion Batteries and Its Application to the Recycling of LCO and LFP

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 149
Author(s):  
Alexandra Holzer ◽  
Stefan Windisch-Kern ◽  
Christoph Ponak ◽  
Harald Raupenstrauch
Keyword(s):  
Lithium Ion Batteries ◽  
Lithium Iron Phosphate ◽  
Process Development ◽  
Removal Rate ◽  
Continuous Process ◽  
Lithium Ion ◽  
Iron Phosphate ◽  
Recycling Process ◽  
Subsequent Step ◽  
Pre Treatment

The bottleneck of recycling chains for spent lithium-ion batteries (LIBs) is the recovery of valuable metals from the black matter that remains after dismantling and deactivation in pre‑treatment processes, which has to be treated in a subsequent step with pyrometallurgical and/or hydrometallurgical methods. In the course of this paper, investigations in a heating microscope were conducted to determine the high-temperature behavior of the cathode materials lithium cobalt oxide (LCO—chem., LiCoO2) and lithium iron phosphate (LFP—chem., LiFePO4) from LIB with carbon addition. For the purpose of continuous process development of a novel pyrometallurgical recycling process and adaptation of this to the requirements of the LIB material, two different reactor designs were examined. When treating LCO in an Al2O3 crucible, lithium could be removed at a rate of 76% via the gas stream, which is directly and purely available for further processing. In contrast, a removal rate of lithium of up to 97% was achieved in an MgO crucible. In addition, the basic capability of the concept for the treatment of LFP was investigated whereby a phosphorus removal rate of 64% with a simultaneous lithium removal rate of 68% was observed.

scholarly journals Parameter optimization and yield prediction of cathode coating separation process for direct recycling of end-of-life lithium-ion batteries

RSC Advances ◽  
2021 ◽  
Vol 11 (39) ◽  
pp. 24132-24136
Author(s):  
Liurui Li ◽  
Tairan Yang ◽  
Zheng Li
Keyword(s):  
Lithium Ion Batteries ◽  
End Of Life ◽  
Lithium Ion ◽  
Separation Process ◽  
Yield Prediction ◽  
Li Ion Batteries ◽  
Treatment Efficiency ◽  
Control Factors ◽  
Li Ion ◽  
Pre Treatment

The pre-treatment efficiency of the direct recycling strategy in recovering end-of-life Li-ion batteries is predicted with levels of control factors.

scholarly journals Predicting the new carbon nanocages, fullerynes: a DFT study

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Mohammad Qasemnazhand ◽  
Farhad Khoeini ◽  
Farah Marsusi
Keyword(s):  
Density Functional Theory ◽  
Lithium Ion Batteries ◽  
Density Functional ◽  
Lithium Ion ◽  
The Other ◽  
Electron Affinities ◽  
Chemical Formula ◽  
Functional Theory ◽  
Triple Bonds ◽  
Structural And Electronic Properties

AbstractIn this study, based on density functional theory, we propose a new branch of pseudo-fullerenes which contain triple bonds with sp hybridization. We call these new nanostructures fullerynes, according to IUPAC. We present four samples with the chemical formula of C4nHn, and the structures derived from fulleranes. We compare the structural and electronic properties of these structures with those of two common fullerenes and fulleranes systems. The calculated electron affinities of the sampled fullerynes are negative, and much smaller than those of fullerenes, so they should be chemically more stable than fullerenes. Although fulleranes also exhibit higher chemical stability than fullerynes, but pentagon or hexagon of the fullerane structures cannot pass ions and molecules. Applications of fullerynes can be included in the storage of ions and gases at the nanoscale. On the other hand, they can also be used as cathode/anode electrodes in lithium-ion batteries.

Transcritical CO2 extraction of electrolytes for lithium-ion batteries: optimization of the recycling process and quality–quantity variation

2017 ◽  
Vol 41 (15) ◽  
pp. 7177-7185 ◽  
Author(s):  
Deying Mu ◽  
Yuanlong Liu ◽  
Ruhong Li ◽  
Quanxin Ma ◽  
Changsong Dai
Keyword(s):  
Lithium Ion Batteries ◽  
Lithium Ion ◽  
Recycling Process ◽  
Separation Processes ◽  
Recovery Method ◽  
Extraction And Separation

A highly-selective electrolyte recovery method-transcritical CO2 extraction—was presented which combined the extraction and separation processes together.

Re-enactment of retrieving lithium ion batteries by sensor ore and magnetic separation process

2020 ◽  
Author(s):  
R. A. Sunmati ◽  
S. V. Tarini ◽  
S. Pooja ◽  
V. Swetha ◽  
S. Thaarini ◽  
...  
Keyword(s):  
Lithium Ion Batteries ◽  
Magnetic Separation ◽  
Lithium Ion ◽  
Separation Process

Research Progress and Application of Modified Silicon-Based Anode Materials for Lithium-Ion Batteries

2021 ◽  
Vol 1036 ◽  
pp. 35-44
Author(s):  
Ling Fang Ruan ◽  
Jia Wei Wang ◽  
Shao Ming Ying
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Volume Expansion ◽  
Anode Materials ◽  
Active Material ◽  
Three Dimensional ◽  
Lithium Ion ◽  
Research Progress ◽  
Ion Intercalation ◽  
Silicon Based

Silicon-based anode materials have been widely discussed by researchers because of its high theoretical capacity, abundant resources and low working voltage platform,which has been considered to be the most promising anode materials for lithium-ion batteries. However,there are some problems existing in the silicon-based anode materials greatly limit its wide application: during the process of charge/discharge, the materials are prone to about 300% volume expansion, which will resultin huge stress-strain and crushing or collapse on the anods; in the process of lithium removal, there is some reaction between active material and current collector, which creat an increase in the thickness of the solid phase electrolytic layer(SEI film); during charging and discharging, with the increase of cycle times, cracks will appear on the surface of silicon-based anode materials, which will cause the batteries life to decline. In order to solve these problems, firstly, we summarize the design of porous structure of nanometer sized silicon-based materials and focus on the construction of three-dimensional structural silicon-based materials, which using natural biomass, nanoporous carbon and metal organic framework as structural template. The three-dimensional structure not only increases the channel of lithium-ion intercalation and the rate of ion intercalation, but also makes the structure more stable than one-dimensional or two-dimensional. Secondly, the Si/C composite, SiOx composite and alloying treatment can improve the volume expansion effection, increase the rate of lithium-ion deblocking and optimize the electrochemical performance of the material. The composite materials are usually coated with elastic conductive materials on the surface to reduce the stress, increase the conductivity and improve the electrochemical performance. Finally, the future research direction of silicon-based anode materials is prospected.

Electrochemical Properties of Carbon-Coated NbO2 as a Negative Electrode for Lithium-Ion Batteries

2016 ◽  
Vol 724 ◽  
pp. 87-91 ◽  
Author(s):  
Chang Su Kim ◽  
Yong Hoon Cho ◽  
Kyoung Soo Park ◽  
Soon Ki Jeong ◽  
Yang Soo Kim
Keyword(s):  
Electrochemical Properties ◽  
Lithium Ion Batteries ◽  
Ball Milling ◽  
Carbon Coating ◽  
Electrochemical Impedance ◽  
Active Material ◽  
Negative Electrode ◽  
Lithium Ion ◽  
Transfer Resistance ◽  
Carbon Coated

We investigated the electrochemical properties of carbon-coated niobium dioxide (NbO2) as a negative electrode material for lithium-ion batteries. Carbon-coated NbO2 powders were synthesized by ball-milling using carbon nanotubes as the carbon source. The carbon-coated NbO2 samples were of smaller particle size compared to the pristine NbO2 samples. The carbon layers were coated non-uniformly on the NbO2 surface. The X-ray diffraction patterns confirmed that the inter-layer distances increased after carbon coating by ball-milling. This lead to decreased charge-transfer resistance, confirmed by electrochemical impedance spectroscopy, allowing electrons and lithium-ions to quickly transfer between the active material and electrolyte. Electrochemical performance, including capacity and initial coulombic efficiency, was therefore improved by carbon coating by ball-milling.

scholarly journals A Sustainable Process for the Recovery of Valuable Metals from Spent Lithium Ion Batteries by Deep Eutectic Solvents Leaching

2022 ◽  
Vol 5 (1) ◽  
pp. 100
Author(s):  
Lourdes Yurramendi ◽  
Jokin Hidalgo ◽  
Amal Siriwardana
Keyword(s):  
Lithium Ion Batteries ◽  
Choline Chloride ◽  
Active Material ◽  
Lithium Ion ◽  
Deep Eutectic Solvents ◽  
Extraction Yield ◽  
Operating Conditions ◽  
Inorganic Acids ◽  
Additive Type ◽  
Valuable Metals

The feasibility of using low-environmental-impact leaching media to recover valuable metals from lithium ion batteries (LIBs) has been evaluated. Several deep eutectic solvents (DES) were tested as leaching agents in the presence of different type of additives (i.e., H2O2). The optimization of Co recovery was carried out by investigating various operating conditions, such as reaction time, temperature, solid (black mass) to liquid (DES) ratio, additive type, and concentration. Leaching with final selected DES choline chloride (33%), lactic acid (53%), and citric acid (13%) at 55 °C achieved an extraction yield of more than 95% for the cobalt. The leaching mechanism likely begins with the dissolution of the active material in the black mass (BM) followed by chelation of Co(II) with the DES. The results obtained confirm that those leaching media are an eco-friendly alternative to the strong inorganic acids used nowadays.

Sign in / Sign up

Export Citation Format

Share Document