scholarly journals Cost and Emissions Reduction in CO2 Capture Plant Dependent on Heat Exchanger Type and Different Process Configurations: Optimum Temperature Approach Analysis

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 425
Author(s):  
Solomon Aforkoghene Aromada ◽  
Nils Henrik Eldrup ◽  
Lars Erik Øi
Keyword(s):  
Heat Exchanger ◽  
Co2 Capture ◽  
Heat Exchangers ◽  
Cost Reduction ◽  
Emissions Reduction ◽  
Cement Plant ◽  
Capture Process ◽  
Shell And Tube ◽  
The Cross ◽  
Vapour Compression

The performance of a plate heat exchanger (PHE), in comparison with the conventional shell and tube types, through a trade-off analysis of energy cost and capital cost resulting from different temperature approaches in the cross-exchanger of a solvent-based CO2 capture process, was evaluated. The aim was to examine the cost reduction and CO2 emission reduction potentials of the different heat exchangers. Each specific heat exchanger type was assumed for the cross-exchanger, the lean amine cooler and the cooler to cool the direct contact cooler’s circulation water. The study was conducted for flue gases from a natural-gas combined-cycle power plant and the Brevik cement plant in Norway. The standard and the lean vapour compression CO2 absorption configurations were used for the study. The PHE outperformed the fixed tube sheet shell and tube heat exchanger (FTS-STHX) and the other STHXs economically and in emissions reduction. The optimal minimum temperature approach for the PHE cases based on CO2 avoided cost were achieved at 4 °C to 7 °C. This is where the energy consumption and indirect emissions are relatively low. The lean vapour compression CO2 capture process with optimum PHE achieved a 16% reduction in CO2 avoided cost in the cement plant process. When the available excess heat for the production of steam for 50% CO2 capture was considered together with the optimum PHE case of the lean vapour compression process, a cost reduction of about 34% was estimated. That is compared to a standard capture process with FTS-STHX without consideration of the excess heat. This highlights the importance of the waste heat at the Norcem cement plant. This study recommends the use of plate heat exchangers for the cross-heat exchanger (at 4–7 °C), lean amine cooler and the DCC unit’s circulation water cooler. To achieve the best possible CO2 capture process economically and in respect of emissions reduction, it is imperative to perform energy cost and capital cost trade-off analysis based on different minimum temperature approaches.

scholarly journals Techno-Economic Assessment of Different Heat Exchangers for CO2 Capture

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6315
Author(s):  
Solomon Aforkoghene Aromada ◽  
Nils Henrik Eldrup ◽  
Fredrik Normann ◽  
Lars Erik Øi
Keyword(s):  
Heat Exchanger ◽  
Co2 Capture ◽  
Heat Exchangers ◽  
Economic Assessment ◽  
Capital Cost ◽  
Plate Heat Exchanger ◽  
Total Annual Cost ◽  
Capture Process ◽  
Plate Heat ◽  
Total Capital

We examined the cost implications of selecting six different types of heat exchangers as the lean/rich heat exchanger in an amine-based CO2 capture process. The difference in total capital cost between different capture plant scenarios due to the different costs of the heat exchangers used as the lean/rich heat exchanger, in each case, is in millions of Euros. The gasketed-plate heat exchanger (G-PHE) saves significant space, and it saves considerable costs. Selecting the G-PHE instead of the shell and tube heat exchangers (STHXs) will save €33 million–€39 million in total capital cost (CAPEX), depending on the type of STHX. About €43 million and €2 million in total installed costs (CAPEX) can be saved if the G-PHE is selected instead of the finned double-pipe heat exchanger (FDP-HX) or welded-plate heat exchanger, respectively. The savings in total annual cost is also in millions of Euros/year. Capture costs of €5/tCO2–€6/tCO2 can be saved by replacing conventional STHXs with the G-PHE, and over €6/tCO2 in the case of the FDP-HX. This is significant, and it indicates the importance of clearly stating the exact type and not just the broad classification of heat exchanger used as lean/rich heat exchanger. This is required for cost estimates to be as accurate as possible and allow for appropriate comparisons with other studies. Therefore, the gasketed-plate heat exchanger is recommended to save substantial costs. The CO2 capture costs of all scenarios are most sensitive to the steam cost. The plate and frame heat exchangers (PHEs) scenario’s capture cost can decline from about €77/tCO2 to €59/tCO2 or rise to €95/tCO2.

scholarly journals Performance Analysis and Design Optimization of Shell and Tube Heat Exchangers

2021 ◽  
Author(s):  
praveen math
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Pressure Loss ◽  
Fluid Flows ◽  
Hot Water ◽  
Flow Conditions ◽  
Shell Side ◽  
Shell And Tube ◽  
Side Flow

Abstract Shell and Tube heat exchangers are having special importance in boilers, oil coolers, condensers, pre-heaters. They are also widely used in process applications as well as the refrigeration and air conditioning industry. The robustness and medium weighted shape of Shell and Tube heat exchangers make them well suited for high pressure operations. The aim of this study is to experiment, validate and to provide design suggestion to optimize the shell and tube heat exchanger (STHE). The heat exchanger is made of acrylic material with 2 baffles and 7 tubes made of stainless steel. Hot fluid flows inside the tube and cold fluid flows over the tube in the shell. 4 K-type thermocouples were used to read the hot and cold fluids inlet and outlet temperatures. Experiments were carried out for various combinations of hot and cold water flow rates with different hot water inlet temperatures. The flow conditions are limited to the lab size model of the experimental setup. A commercial CFD code was used to study the thermal and hydraulic flow field inside the shell and tubes. CFD methodology is developed to appropriately represent the flow physics and the procedure is validated with the experimental results. Turbulent flow in tube side is observed for all flow conditions, while the shell side has laminar flow except for extreme hot water temperatures. Hence transition k-kl-omega model was used to predict the flow better for transition cases. Realizable k- epsilon model with non-equilibrium wall function was used for turbulent cases. Temperature and velocity profiles are examined in detail and observed that the flow remains almost uniform to the tubes thus limiting heat transfer. Approximately 2/3 rd of the shell side flow does not surround the tubes due to biased flow contributing to reduced overall heat transfer and increased pressure loss. On the basis of these findings an attempt has been made to enhance the heat transfer by inducing turbulence in the shel l side flow. The two baffles were rotated in opposite direction to each other to achieve more circulation in the shell side flow and provide more contact with tube surface. Various positions of the baffles were simulated and studied using CFD analysis and th e results are summarized with respect to heat transfer and pressure loss.

The Stress Analysis of Heat Exchanger Expansion Joints in the Elastic Range

1973 ◽  
Vol 95 (1) ◽  
pp. 145-150 ◽  
Author(s):  
L. J. Wolf ◽  
R. M. Mains
Keyword(s):  
Heat Exchanger ◽  
Stress Analysis ◽  
Strain Gage ◽  
Analytical Method ◽  
Heat Exchangers ◽  
Expansion Joints ◽  
Elastic Range ◽  
Shell And Tube ◽  
Strain Gage Tests

Expansion joints of the style most commonly used in shell and tube heat exchangers were studied analytically and experimentally in the elastic range. A method of computing stresses and deformations for pressure and expansion loadings is demonstrated. Strain-gage tests show the analytical method to be accurate.

Hybrid Particle Swarm Optimization and Ant Colony Optimization Technique for the Optimal Design of Shell and Tube Heat Exchangers

2015 ◽  
Vol 10 (2) ◽  
pp. 81-96 ◽  
Author(s):  
Sandip K. Lahiri ◽  
Nadeem Muhammed Khalfe
Keyword(s):  
Particle Swarm Optimization ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Optimization Technique ◽  
Particle Swarm ◽  
Ant Colony ◽  
Swarm Optimization ◽  
Hybrid Particle Swarm Optimization ◽  
Shell And Tube ◽  
Operational Constraints

Abstract Owing to the wide utilization of shell and tube heat exchangers (STHEs) in industrial processes, their cost minimization is an important target for both designers and users. Traditional design approaches are based on iterative procedures which gradually change the design and geometric parameters until satisfying a given heat duty and set of geometric and operational constraints. Although well proven, this kind of approach is time-consuming and may not lead to cost-effective design. The present study explores the use of non-traditional optimization technique called hybrid particle swarm optimization (PSO) and ant colony optimization (ACO), for design optimization of STHEs from economic point of view. The PSO applies for global optimization and ant colony approach is employed to update positions of particles to attain rapidly the feasible solution space. ACO works as a local search, wherein ants apply pheromone-guided mechanism to update the positions found by the particles in the earlier stage. The optimization procedure involves the selection of the major geometric parameters such as tube diameters, tube length, baffle spacing, number of tube passes, tube layout, type of head, baffle cut, etc. and minimization of total annual cost is considered as design target. The methodology takes into account the geometric and operational constraints typically recommended by design codes. Three different case studies are presented to demonstrate the effectiveness and accuracy of proposed algorithm. The examples analyzed show that the hybrid PSO and ACO algorithm provides a valuable tool for optimal design of heat exchanger. The hybrid PSO and ACO approach is able to reduce the total cost of heat exchanger as compare to cost obtained by previously reported genetic algorithm (GA) approach. The result comparisons with particle swarm optimizer and other optimization algorithms (GA) demonstrate the effectiveness of the presented method.

Economic Optimization of Shell and Tube Heat Exchanger Based on Constructal Theory

2010 ◽  
Author(s):  
Majid Amidpour ◽  
Abazar Vahdat Azad
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Constructal Theory ◽  
Economic Optimization ◽  
Total Cost ◽  
Tube Heat Exchanger ◽  
Capital Costs ◽  
Operational Energy ◽  
Shell And Tube

In this paper, the new approach of Constructal theory has been employed to design shell and tube heat exchangers. Constructal theory is a new method for optimal design in engineering applications. The purpose of this paper is optimization of shell and tube heat exchangers by reduction of total cost of the exchanger using the constructal theory. The total cost of the heat exchanger is the sum of operational costs and capital costs. The overall heat transfer coefficient of the shell and tube heat exchanger is increased by the use of constructal theory. Therefore, the capital cost required for making the heat transfer surface is reduced. Moreover, the operational energy costs involving pumping in order to overcome frictional pressure loss are minimized in this method. Genetic algorithm is used to optimize the objective function which is a mathematical model for the cost of the shell and tube heat exchanger and is based on constructal theory. The results of this research represent more than 50% reduction in costs of the heat exchanger.

Deflections of A Multipass Shell-and-Tube Heat Exchanger Bolted Joint Subjected to Nonaxisymmetric Thermal Loading

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Natalia Petrova ◽  
Abdel-Hakim Bouzid
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Thermal Loading ◽  
Cocurrent Flow ◽  
Finite Element Models ◽  
Bolted Joint ◽  
Tube Heat Exchanger ◽  
Specific Geometry ◽  
Shell And Tube

Despite the fact that multipass shell-and-tube heat exchangers operating at high temperature are subject to frequent problems related to flange sealing, there is neither detailed explanations for the reasons of the failures nor an adequate solution to this problem. Specific geometry of multipass heat exchangers and the temperature difference between the inlet and the outlet fluids is responsible for the existence of a thermal circumferential gradient at the shell-to-channel bolted joint. However, existing flange design methods do not address nonaxisymmetrical temperature loading of the flanged joint assembly. The circumferential thermal gradient, as the cause of frequent failures to seal the flanged joints, is ignored. This paper outlines the analytical modeling of a flanged joint with a tube sheet of a multipass heat exchanger subjected to a nonaxisymmetrical thermal loading. A shell-and-tube heat exchanger of 51 in. diameter with cocurrent flow was used for analysis. The main steps of the theoretical analysis used for the determination of the circumferential temperature profiles and the thermal expansion displacements and distortions of the bolted joint components are given. The results from the proposed analytical model are compared with those obtained from finite element models.

A Numerical Algorithm and a Graphical Method to Size a Heat Exchanger

2011 ◽  
Author(s):  
Torsten Berning
Keyword(s):  
Heat Exchanger ◽  
Numerical Algorithm ◽  
Heat Exchangers ◽  
Graphical Method ◽  
Application Software ◽  
Microsoft Excel ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Heat Exchanger Design ◽  
Shell And Tube

This paper describes the development of a numerical algorithm and a graphical method that can be employed in order to determine the overall heat transfer coefficient inside heat exchangers. The method is based on an energy balance and utilizes the spreadsheet application software Microsoft Excel™. The application is demonstrated in an example for designing a single pass shell and tube heat exchanger that was developed in the Department of Materials Technology of the Norwegian University of Science and Technology (NTNU) where water vapor is superheated by a secondary oil cycle. This approach can be used to reduce the number of hardware iterations in heat exchanger design.

scholarly journals Thermal Performance in Heat Exchangers by the Irreversibility, Effectiveness, and Efficiency Concepts Using Nanofluids

2020 ◽  
Vol 7 (2) ◽  
pp. F1-F7
Author(s):  
E. Nogueira
Keyword(s):  
Heat Exchanger ◽  
Ethylene Glycol ◽  
Heat Exchangers ◽  
Volume Fraction ◽  
Second Law Of Thermodynamics ◽  
Second Law ◽  
Output Data ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Effectiveness And Efficiency

The objective of the work is to obtain the outlet temperatures of the fluids in a shell and tube heat exchanger. The second law of thermodynamics is applied through the concepts of efficiency, effectiveness, and irreversibility to analyze the results. Water flows in the shell, and a mixture of water-ethylene glycol is associated with fractions of nanoparticles flows in the tube. Water enters the shell at 27 °C, and the mixture comes to the tube at 90 °C. The mass flow is kept fixed in the shell, equal to 0.23 kg/s, and varies between 0.01 kg/s to 0.50 kg/s. Volume fractions equal to 0.01, 0.10, and 0.25 were considered for analysis, for both nanoparticles from Ag and Al2O3. Results for Reynolds number, heat transfer rate, efficiency, effectiveness, and irreversibility are presented for critique, discussion, and justification of the output data found. It is shown that the flow regime has a significant effect on the performance of the analyzed heat exchanger. Keywords: thermodynamics, second law, ethylene glycol, volume fraction.

scholarly journals Study on Shell-and-Tube Heat Exchanger Models with Different Degree of Complexity for Process Simulation and Control Design

2018 ◽  
Author(s):  
Javier Bonilla
Keyword(s):  
Heat Exchanger ◽  
Molten Salt ◽  
Heat Exchangers ◽  
Control Strategies ◽  
Thermal Storage ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Test Loop ◽  
Shell And Tube ◽  
Thermal Oil

Many commercial solar thermal power plants rely on indirect thermal storage systems in order to provide a stable and reliable power supply, where the working fluid is commonly thermal oil and the storage fluid is molten salt. The thermal oil - molten salt heat exchanger control strategies, to charge and discharge the thermal storage system, strongly affect the performance of the whole plant. Shell-and-tube heat exchangers are the most common type of heat exchangers used in these facilities. With the aim of developing advanced control strategies accurate and fast dynamic models of shell-and-tube heat exchangers are essential. For this reason, several shell-and-tube heat exchanger models with different degrees of complexity have been studied, analyzed and validated against experimental data from the CIEMAT-PSA molten salt test loop for thermal energy systems facility. Simulation results are compared in steady-state as well as transient predictions in order to determine the required complexity of the model to yield accurate results.

A General Expression for the Determination of the Log Mean Temperature Correction Factor for Shell and Tube Heat Exchangers

2003 ◽  
Vol 125 (3) ◽  
pp. 527-530 ◽  
Author(s):  
Ahmad Fakheri
Keyword(s):  
Heat Exchanger ◽  
Correction Factor ◽  
Heat Exchangers ◽  
Direct Determination ◽  
Temperature Correction ◽  
Tube Heat Exchanger ◽  
Mean Temperature ◽  
Shell And Tube ◽  
Graphical Presentation

This paper presents a single closed form algebraic equation for the determination of the Log Mean Temperature Difference correction factor F for shell and tube heat exchangers having N shell passes and 2M tube passes per shell. The equation and its graphical presentation generalize the traditional equations and charts used for the determination of F. The equation presented is also useful in design, analysis and optimization of multi shell and tube heat exchanger, particularly for direct determination of the number of shells.

Sign in / Sign up

Export Citation Format

Share Document