scholarly journals Numerical Investigation of Steady and Harmonic Vortex Generator Jets Flow Separation Control

Fluids ◽  
2018 ◽  
Vol 3 (4) ◽  
pp. 94 ◽  
Author(s):  
Aria Alimi ◽  
Olaf Wünsch
Keyword(s):  
Flow Control ◽  
Large Scale ◽  
Active Flow Control ◽  
Vortex Generator ◽  
Boundary Layer Separation ◽  
Transition To Turbulence ◽  
Momentum Exchange ◽  
Hairpin Vortices ◽  
Flow Separation Control ◽  
Vortex Generator Jets

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient at reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures forming immediately downstream of the injection location led to the formation of hairpin-type vortices, causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs, as well. However, the increased control effectiveness for harmonic VGJs’ flow control strategy is attributed to the fact that the shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified, leading to the development of large-scale coherent structures, which are very effective at increasing the momentum exchange, thus limiting the separated region.

scholarly journals Control of Laminar Boundary-Layer Separation Using Steady and Harmonic Vortex Generator Jets

2018 ◽  
Author(s):  
Aria Alimi ◽  
Olaf Wünsch
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Laminar Boundary Layer ◽  
Active Flow Control ◽  
Vortex Generator ◽  
Boundary Layer Separation ◽  
Transition To Turbulence ◽  
Momentum Exchange ◽  
Layer Separation ◽  
Vortex Generator Jets

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

scholarly journals Control of Laminar Boundary-Layer Separation Using Steady and Harmonic Vortex Generator Jets

2018 ◽  
Author(s):  
Aria Alimi ◽  
Olaf Wünsch
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Laminar Boundary Layer ◽  
Active Flow Control ◽  
Vortex Generator ◽  
Boundary Layer Separation ◽  
Transition To Turbulence ◽  
Momentum Exchange ◽  
Layer Separation ◽  
Vortex Generator Jets

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

Direct Numerical Simulations of a Laminar Separation Bubbles on a Curved Plate: Part 2 — Flow Control Using Pulsed Vortex Generator Jets

2013 ◽  
Author(s):  
Wolfgang Balzer ◽  
Hermann F. Fasel
Keyword(s):  
Flow Control ◽  
Numerical Simulations ◽  
Large Scale ◽  
Separation Bubble ◽  
Hydrodynamic Instability ◽  
Active Flow Control ◽  
Vortex Generator ◽  
Direct Numerical Simulations ◽  
Laminar Separation ◽  
Vortex Generator Jets

Highly-accurate direct numerical simulations (DNS) are employed to investigate active flow control of laminar boundary layer separation by means of pulsed vortex generator jets (VGJs), i.e. by injecting fluid into the flow through a spanwise array of small holes. The uncontrolled flow configuration is represented by a laminar separation bubble developing on a curved-plate geometry modeling the convex suction-side curvature of the Pratt&Whitney “PackB” research blade. The simulation setup and uncontrolled flow results were presented in part I of the present paper. In this second part, particular focus is directed towards identifying the relevant physical mechanisms associated with VGJ control of low Reynolds number separation, as for example encountered in low-pressure turbine applications. The numerical results confirm findings of earlier flat-plate simulations, which showed that the control effectiveness of pulsed VGJs can be explained by the fact that linear hydrodynamic instability mechanisms are exploited. When pulsing with frequencies to which the (uncontrolled) separated shear layer is naturally unstable, instability modes are shown to develop into large-scale, spanwise-coherent structures. These structures provide the necessary entrainment of high-momentum fluid causing a much sooner reattachment of the separated flow compared to the uncontrolled flow and consequently leading to a significant reduction in performance losses.

Study on Flow Separation Control by Vortex Generator Jets with Different Parameters

2012 ◽  
Vol 588-589 ◽  
pp. 1786-1789
Author(s):  
Yong Hui Xie ◽  
Zhong Yang Shen ◽  
Tao Fan
Keyword(s):  
Flow Control ◽  
Flow Separation ◽  
Vortex Generator ◽  
Separation Control ◽  
Flow Separation Control ◽  
Profound Influence ◽  
Orthogonal Analysis ◽  
Conical Diffuser ◽  
Flow Charts ◽  
Vortex Generator Jets

In order to investigate the mechanism of flow separation control in conical diffuser by vortex generator jets (VGJs) method, numerical simulations were conducted to discuss the effect of VGJs with different parameters on flow control. The aerodynamic performance in conical diffuser with angle of 14° was tested and analyzed based on Shear-Stress-Transport (SST) simulation. The flow charts at several sections were analyzed, illuminating the formation of complex vortices. Moreover, the effects of 5 VGJs parameters on the diffuser were analyzed by orthogonal analysis. It was shown that the number of jets and the pitch angle of jet showed more profound influence on the flow control by VGJs.

Active Flow Separation Control Using Endwall Vortex Generator Jets in Highly Loaded Compressor Cascades

2015 ◽  
Author(s):  
Yanyan Feng ◽  
Yanping Song ◽  
Fu Chen ◽  
Huaping Liu
Keyword(s):  
Flow Separation ◽  
Active Flow Control ◽  
Vortex Generator ◽  
Control Technique ◽  
Flow Separation Control ◽  
Positive Effects ◽  
Loss Coefficients ◽  
Vortex Generator Jets ◽  
Active Flow ◽  
Highly Loaded

An active flow control technique of endwall vortex generator jets (VGJs) was used in two kinds of highly loaded compressor cascades. Numerical investigations were carried out on a NACA 65 profile with a large camber angle at low subsonic and high subsonic speeds, and a CDA profile at high subsonic speed respectively. The results indicate that the endwall VGJs can restrain flow separation effectively by reenergizing the boundary layer fluid and resisting the transverse movement of endwall secondary flow. At Mach number 0.23, the results of the jet blowing ratio study illustrate that the increasing jet velocity shows noteworthy potential to improve the cascade aerodynamic performance. The double jets structures were investigated yet gains weaker beneficial effects than single jet. It is probably attributed to the complex flow structure, leading to strong disturbance and large-scale mixing loss. Under −5°, 0° and +5° angles of attack, the loss coefficients are maximally reduced by 4.1%, 9.5% and 17.3% respectively. Under high subsonic conditions, the endwall VGJs still has significantly positive effects on NACA 65 profile. Considering the small separation region of CDA, the loss coefficients increase slightly although the flow separation is weakened further by VGJ.

Flow Control for Wind Turbine Airfoil

2011 ◽  
Author(s):  
Andreas Gross ◽  
Hermann F. Fasel
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Active Flow Control ◽  
Turbine Blades ◽  
Vortex Generator ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Plasma Actuators ◽  
Flip Flop ◽  
Wind Turbine Airfoil

The flow over a NREL S822 wind turbine airfoil was simulated for a chord Reynolds number of 100,000 and an angle of attack of 5deg. These conditions approximately match the blade element conditions at 80% radius of a 2m diameter turbine operating at 300rpm. A simulation of the uncontrolled flow with steady approach flow conditions shows boundary layer separation on the suction side which is consistent with University of Illinois at Urbana-Champaign experimental data. Active flow control has the potential to locally (and on demand) reduce the unsteady loads on individual turbine blades during non-nominal operation, thereby increasing turbine life. In addition, flow control may help lower the cut-in wind speed. Unsteady flow control for reducing the suction side separation using pulsed vortex generator jets, flip-flop jets, and plasma actuators were evaluated. It was found that very low actuation amplitudes were already sufficient for eliminating the suction side separation. The high effectiveness and efficiency is traced back to hydrodynamic instabilities that lead to a downstream growth of the forced disturbances. Too high actuator amplitudes resulted in early disturbance saturation which made the control inefficient.

Control of laminar separation using pulsed vortex generator jets: direct numerical simulations

2011 ◽  
Vol 676 ◽  
pp. 81-109 ◽  
Author(s):  
D. POSTL ◽  
W. BALZER ◽  
H. F. FASEL
Keyword(s):  
Numerical Simulations ◽  
Large Scale ◽  
Hydrodynamic Instability ◽  
Vortex Generator ◽  
Boundary Layer Separation ◽  
Direct Numerical Simulations ◽  
Laminar Separation ◽  
Momentum Coefficient ◽  
Instability Modes ◽  
Vortex Generator Jets

Direct numerical simulations (DNS) are employed to investigate laminar boundary layer separation and its control by pulsed vortex generator jets (VGJs), i.e. by injecting fluid into the flow through a spanwise array of small holes. Particular focus is directed towards identifying the relevant physical mechanisms associated with VGJ control of low-Reynolds-number separation, as encountered in low-pressure turbine applications. Pulsed VGJs are shown to be much more effective than steady VGJs when the same momentum coefficient is used for the actuation. From our investigations we have found that the increased control effectiveness of pulsed VGJs can be explained by the fact that linear hydrodynamic instability mechanisms are exploited. When pulsing with frequencies to which the separated shear layer is naturally unstable, instability modes are shown to develop into large-scale, spanwise coherent structures. These structures provide the necessary entrainment of high-momentum fluid to successfully reattach the flow.

Impact of the Precessing Vortex Core on NOx Emissions in Premixed Swirl-Stabilized Flames: An Experimental Study

2020 ◽  
Author(s):  
Finn Lückoff ◽  
Moritz Sieber ◽  
Christian Oliver Paschereit ◽  
Kilian Oberleithner
Keyword(s):  
Flow Control ◽  
Large Scale ◽  
Active Flow Control ◽  
Premixed Flame ◽  
Nox Emissions ◽  
Precessing Vortex Core ◽  
Flame Dynamics ◽  
Swirl Flows ◽  
Active Flow ◽  
The Impact

Abstract The reduction of polluting NOx emission remains a driving factor in the design process of swirl-stabilized combustion systems, to meet strict legislative restrictions. In reacting swirl flows, hydrodynamic coherent structures, such as periodic large-scale vortices in the shear layer, induce zones with increased heat release rate fluctuations in connection with temperature peaks, which lead to an increase of NOx emissions. Such large-scale vortices can be induced by the helical coherent structure known as precessing vortex core (PVC), which influences the flow and flame dynamics of reacting swirl flows under certain operating conditions. We developed an active flow control system, which allows for a targeted actuation of the PVC, to investigate its impact on important combustion properties. In this study, the direct active flow control is used to actuate a PVC of arbitrary frequency and amplitude, which facilitates a systematic study of the impact of the PVC on NOx emissions. In the course of the present work, a perfectly premixed flame, which slightly damps the PVC, is studied in detail. Since the PVC is slightly damped, it can be precisely excited by means of open-loop flow control. In connection with time-resolved OH*-chemiluminescence and stereoscopic PIV measurements, the flame and flow response to PVC actuation as well as the impact of the actuated PVC on flow and flame dynamics are characterized. It turns out that the PVC rolls up the inner shear layer, which results in an interaction of PVC-induced vortices and flame. This interaction considerably influences the measured level of NOx emissions, which grow with increasing PVC amplitude in a perfectly premixed flame. Nearly the same increase is to be seen for a partially premixed flame. This in contrast to previous studies, where the PVC is assumed to reduce the NOx emissions due to vortex-enhanced mixing.

The Fluid Dynamics of LPT Blade Separation Control Using Pulsed Jets

2001 ◽  
Author(s):  
Jeffrey P. Bons ◽  
Rolf Sondergaard ◽  
Richard B. Rivir
Keyword(s):  
Boundary Layer ◽  
Duty Cycle ◽  
Separation Bubble ◽  
Vortex Generator ◽  
Boundary Layer Separation ◽  
Skew Angle ◽  
Suction Surface ◽  
Duty Cycles ◽  
Wide Range ◽  
Vortex Generator Jets

The effects of pulsed vortex generator jets on a naturally separating low pressure turbine boundary layer have been investigated experimentally. Blade Reynolds numbers in the linear turbine cascade match those for high altitude aircraft engines and industrial turbine engines with elevated turbine inlet temperatures. The vortex generator jets (30 degree pitch and 90 degree skew angle) are pulsed over a wide range of frequency at constant amplitude and selected duty cycles. The resulting wake loss coefficient vs. pulsing frequency data add to previously presented work by the authors documenting the loss dependency on amplitude and duty cycle. As in the previous studies, vortex generator jets are shown to be highly effective in controlling laminar boundary layer separation. This is found to be true at dimensionless forcing frequencies (F+) well below unity and with low (10%) duty cycles. This unexpected low frequency effectiveness is due to the relatively long relaxation time of the boundary layer as it resumes its separated state. Extensive phase-locked velocity measurements taken in the blade wake at an F+ of 0.01 with 50% duty cycle (a condition at which the flow is essentially quasi-steady) document the ejection of bound vorticity associated with a low momentum fluid packet at the beginning of each jet pulse. Once this initial fluid event has swept down the suction surface of the blade, a reduced wake signature indicates the presence of an attached boundary layer until just after the jet termination. The boundary layer subsequently relaxes back to its naturally separated state. This relaxation occurs on a timescale which is 5–6 times longer than the original attachment due to the starting vortex. Phase-locked boundary layer measurements taken at various stations along the blade chord illustrate this slow relaxation phenomenon. This behavior suggests that some economy of jet flow may be possible by optimizing the pulse duty cycle and frequency for a particular application. At higher pulsing frequencies, for which the flow is fully dynamic, the boundary layer is dominated by periodic shedding and separation bubble migration, never recovering its fully separated (uncontrolled) state.

Sign in / Sign up

Export Citation Format

Share Document