scholarly journals Improved Fracture Toughness and Conversion Degree of Resin-Based Dental Composites after Modification with Liquid Rubber

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2704
Author(s):  
Krzysztof Pałka ◽  
Joanna Kleczewska ◽  
Emil Sasimowski ◽  
Anna Belcarz ◽  
Agata Przekora
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Dental Materials ◽  
Degree Of Conversion ◽  
Dental Composites ◽  
Conversion Degree ◽  
Matrix Resin ◽  
Ceramic Filler ◽  
Liquid Rubber ◽  
The Matrix

There are many methods widely applied in the engineering of biomaterials to improve the mechanical properties of the dental composites. The aim of this study was to assess the effect of modification of dental composites with liquid rubber on their mechanical properties, degree of conversion, viscosity, and cytotoxicity. Both flow and packable composite consisted of a mixture of Bis-GMA, TEGDMA, UDMA, and EBADMA resins reinforced with 60 and 78 wt.% ceramic filler, respectively. It was demonstrated that liquid rubber addition significantly increased the fracture toughness by 9% for flow type and 8% for condensable composite. The influence of liquid rubber on flexural strength was not statistically significant. The addition of the toughening agent significantly reduced Young’s modulus by 7% and 9%, respectively, while increasing deformation at breakage. Scanning electron microscopy (SEM) observations allowed to determine the mechanisms of toughening the composites reinforced with ceramic particles. These mechanisms included bridging the crack edges, blocking the crack tip by particles and dissipation of fracture energy by deflection of the cracks on larger particles. The degree of conversion increased after modification, mainly due to a decrease in the matrix resin viscosity. It was also shown that all dental materials were nontoxic according to ISO 10993-5, indicating that modified materials have great potential for commercialization and clinical applications.

scholarly journals Chemical and Mechanical Properties of Experimental Dental Composites as a Function of Formulation and Postcuring Thermal Treatment

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Renata A. Esteves ◽  
Letícia C. C. Boaro ◽  
Flávia Gonçalves ◽  
Luiza M. P. Campos ◽  
Cecy M. Silva ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Elastic Modulus ◽  
Thermal Treatment ◽  
Flexural Strength ◽  
Low Cost ◽  
Chemical Properties ◽  
Degree Of Conversion ◽  
Dental Composites ◽  
Molar Ratios

This study evaluated the influence of formulation and thermal treatment on the degree of conversion, fracture toughness, flexural strength, and elastic modulus of experimental composites. Six composites were analyzed at BisGMA : TEGDMA molar ratios of 1 : 1 and 7 : 3 with filler at 30, 50, and 70 wt%. The degree of conversion was analyzed by Fourier transform infrared spectroscopy, fracture toughness was measured using the single-edge notched beam, and flexural strength and elastic modulus were measured with the 3-point bend test. For all tests, one-half of the specimens received thermal treatment at 170°C for 10 min. Data were analyzed by the Kruskal-Wallis or ANOVA/Tukey’s test (α = 5%). The 1 : 1 BisGMA : TEGDMA ratio showed higher properties than the 7 : 3 ratio. Although the material with 70% filler had a conversion lower than the one with 50%, it showed higher mechanical properties. The thermal treatment improved all properties in all materials. Therefore, the use of an equimolar ratio of BisGMA : TEGDMA can be paired with 70 wt% filler to design dental composites that possess increased advantageous physical and chemical properties. Furthermore, the simple and low-cost method of thermal treatment proposed for use in clinical dentistry has been shown to effectively improve the properties of all evaluated materials.

scholarly journals The Effect of Liquid Rubber Addition on the Physicochemical Properties, Cytotoxicity and Ability to Inhibit Biofilm Formation of Dental Composites

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1704
Author(s):  
Krzysztof Pałka ◽  
Małgorzata Miazga-Karska ◽  
Joanna Pawłat ◽  
Joanna Kleczewska ◽  
Agata Przekora
Keyword(s):  
Cell Viability ◽  
Biofilm Formation ◽  
Bacterial Biofilm ◽  
Type Material ◽  
Dental Composites ◽  
Antibiofilm Activity ◽  
Ceramic Filler ◽  
Liquid Rubber ◽  
Flow Type ◽  
Type Composite

The aim of this study was to evaluate the effect of modification with liquid rubber on the adhesion to tooth tissues (enamel, dentin), wettability and ability to inhibit bacterial biofilm formation of resin-based dental composites. Two commercial composites (Flow-Art–flow type with 60% ceramic filler and Boston–packable type with 78% ceramic filler; both from Arkona Laboratorium Farmakologii Stomatologicznej, Nasutów, Poland) were modified by addition of 5% by weight (of resin) of a liquid methacrylate-terminated polybutadiene. Results showed that modification of the flow type composite significantly (p < 0.05) increased the shear bond strength values by 17% for enamel and by 33% for dentine. Addition of liquid rubber significantly (p < 0.05) reduced also hydrophilicity of the dental materials since the water contact angle was increased from 81–83° to 87–89°. Interestingly, modified packable type material showed improved antibiofilm activity against Steptococcus mutans and Streptococcus sanguinis (quantitative assay with crystal violet), but also cytotoxicity against eukaryotic cells since cell viability was reduced to 37% as proven in a direct-contact WST-8 test. Introduction of the same modification to the flow type material significantly improved its antibiofilm properties (biofilm reduction by approximately 6% compared to the unmodified material, p < 0.05) without cytotoxic effects against human fibroblasts (cell viability near 100%). Thus, modified flow type composite may be considered as a candidate to be used as restorative material since it exhibits both nontoxicity and antibiofilm properties.

Effect of the matrix resin structure on the mechanical properties and braking performance of organic brake pads

2012 ◽  
Vol 126 (5) ◽  
pp. 1746-1753 ◽  
Author(s):  
Hai-Qing Wang ◽  
Xing-Yang Wu ◽  
Tong-Sheng Li ◽  
Xu-Jun Liu ◽  
Pei-Hong Cong
Keyword(s):  
Mechanical Properties ◽  
Matrix Resin ◽  
Braking Performance ◽  
Brake Pads ◽  
The Matrix

Microstructure, Mechanical Properties, Sintering and Fracture Behavior of Ti(C, N) Based Cermets Granules/Ti(C, N) Based Cermets Composite

2020 ◽  
Vol 837 ◽  
pp. 139-145
Author(s):  
Ai Jun Liu ◽  
Gang Li ◽  
Ning Liu ◽  
Ke Bei Chen ◽  
Hai Dong Yang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Relative Density ◽  
Fracture Behavior ◽  
Rupture Strength ◽  
Binder Phase ◽  
Hard Phase ◽  
Opposite Trend ◽  
The Matrix ◽  
Sintering Properties

Effect of Ti (C,N) based cermets granule on the microstructure, mechanical properties, sintering and fracture behavior of Ti (C,N) based cermets was investigated. Results show that the Ti (C,N) based cermets granules distribute in the matrix homogeneously. A nanoindentation study was performed on hard phase and binder phase in the matrix and granule. With the increase of granules content, sintering properties is worse. With the increase of granules content, transverse rupture strength (TRS) and relative density decrease gradually, while the hardness has an opposite trend. The fracture toughness increases firstly with increasing granule, and then decreases with the further increase of granules. Higher fracture toughness of the cermets is mainly owing to the crack branch and higher fracture energy of coarse granule.

Mechanical Properties of Machinable Zirconia Dental Composites

2007 ◽  
Vol 336-338 ◽  
pp. 1587-1589
Author(s):  
Wen Xu Li ◽  
Hua Zhao ◽  
Ying Song ◽  
Bin Su ◽  
Fu Ping Wang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Calcium Phosphate ◽  
Flexural Strength ◽  
Dental Composite ◽  
The Other ◽  
Dental Composites ◽  
Composite Ceramics ◽  
Cad Cam ◽  
The Common

Ca3(PO4)2/ZrO2 dental composite ceramics using for CAD/CAM system were prepared and the effects of weak phases on microstructures and mechanical properties were studied. The results showed that intergranular spreads happened with the increasing Ca3(PO4)2 contents due to the discontinuity of weak interfaces between Zirconia and Calcium phosphate in matrix. So the flexural strength and hardness of the Ca3(PO4)2/ZrO2 composite ceramics were decreased effectively, which improved the machinability of the composites. On the other hand, strong interfaces between Zirconias increased the integrality of the ceramic structures. ZrO2 composite Ceramics with 15% Ca3(PO4)2 were sintered at 1350°C. The flexural strength is 300.44MPa, fracture toughness is 4.36 MPam1/2, and hardness is 6.69 GPa. The cutting exponent of the Ca3(PO4)2/ZrO2 composite ceramics is obviously lower than that of the common commercial Vita Mark II and Dicor MGC ceramics, which shows good mechanical properties and machinability.

scholarly journals Multiscale Characterization of Nanoengineered Fiber-Reinforced Composites: Effect of Carbon Nanotubes on the Out-of-Plane Mechanical Behavior

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Carlos Medina ◽  
Eduardo Fernandez ◽  
Alexis Salas ◽  
Fernando Naya ◽  
Jon Molina-Aldereguía ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Shear Strength ◽  
Mechanical Behavior ◽  
Matrix Interface ◽  
Short Beam ◽  
The Matrix ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

The mechanical properties of the matrix and the fiber/matrix interface have a relevant influence over the mechanical properties of a composite. In this work, a glass fiber-reinforced composite is manufactured using a carbon nanotubes (CNTs) doped epoxy matrix. The influence of the CNTs on the material mechanical behavior is evaluated on the resin, on the fiber/matrix interface, and on the composite. On resin, the incorporation of CNTs increased the hardness by 6% and decreased the fracture toughness by 17%. On the fiber/matrix interface, the interfacial shear strength (IFSS) increased by 22% for the nanoengineered composite (nFRC). The influence of the CNTs on the composite behavior was evaluated by through-thickness compression, short beam flexural, and intraply fracture tests. The compressive strength increased by 6% for the nFRC, attributed to the rise of the matrix hardness and the fiber/matrix IFSS. In contrast, the interlaminar shear strength (ILSS) obtained from the short beam tests was reduced by 8% for the nFRC; this is attributed to the detriment of the matrix fracture toughness. The intraply fracture test showed no significant influence of the CNTs on the fracture energy; however, the failure mode changed from brittle to ductile in the presence of the CNTs.

Experimental Study on Mechanical Properties of Epoxy/MWCNT Nanocomposites—Effects of Acid Treatment, Pressured Curing, and Liquid Rubber

2012 ◽  
Vol 3 (1) ◽  
Author(s):  
Yuan Li ◽  
Ning Hu ◽  
Takashi Kojima ◽  
Takaomi Itoi ◽  
Tomonori Watanabe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
Acid Treatment ◽  
Tensile Tests ◽  
Type I ◽  
Multiwalled Carbon ◽  
Liquid Rubber ◽  
Type Iv ◽  
Positive Effect

The unique properties of carbon nanotube (CNT) have made it very attractive as reinforcement in polymer nanocomposites in the hope of effectively improving the mechanical properties. In order to explore the effects of three appealing influencing factors, i.e., acid treatment, pressured curing, and liquid rubber (LR) on mechanical properties of nanocomposites, tensile tests, and single-edge notched bending (SENB) tests are carried out for four types of CNT-reinforced nanocomposites. Compared with type I of nanocomposites using pristine multiwalled carbon nanotube (MWCNT) as reinforcement for epoxy, which are termed as Epoxy/MWCNT, type II of Epoxy/MWCNT-COOH nanocomposites with acid-treated MWCNTs as reinforcement, show obvious improvement on tensile properties and fracture toughness. This positive effect of acid treatment can be attributed to better dispersion of CNTs and stronger interface based on the corresponding fracture surfaces. For type III of P-Epoxy/MWCNT-COOH nanocomposites under pressured curing, although the voids in samples are decreased effectively and the interface is strengthened, there is no expected positive results because of severe CNTs agglomeration. For type IV of P-Epoxy/LR/MWCNT-COOH nanocomposites, addition of LR results in at least around a threefold increase in fracture toughness compared with that of P-Epoxy/MWCNT-COOH, indicating the amazing effect of LR. The present work provides much more choices for fabricating specific CNT-reinforced nanocomposites with desired properties by reasonably combining proper fabrication conditions including acid treatment, pressured curing, liquid rubber with polymer matrix, and reinforcement loading.

scholarly journals Effects of Cobalt Content on the Microstructure, Mechanical Properties and Cavitation Erosion Resistance of HVOF Sprayed Coatings

Coatings ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 534 ◽  
Author(s):  
Liu ◽  
Bai ◽  
Chen ◽  
Yuan
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Surface Roughness ◽  
Cavitation Erosion ◽  
Cobalt Content ◽  
Alloy Coating ◽  
Matrix Phase ◽  
Hvof Spraying ◽  
The Matrix ◽  
Cavitation Erosion Resistance

Cobalt-based alloy coatings and WC-Co-based ceramic–metal (cermet) coatings have been widely used because of their desirable mechanical properties and corrosion resistance. In this work, the influence of Co content on the microstructure, mechanical properties and cavitation erosion (CE) resistance were investigated. A cobalt-based alloy coating, a WC-12Co coating, and a WC-17Co cermet coating were deposited by high-velocity oxygen fuel (HVOF) spraying on 1Cr18Ni9Ti substrates. Results indicate that the cobalt-based alloy coating had the largest surface roughness because surface-bonded particles of lower plastic deformation were flattened. The existence of WC particles had led to an increase in hardness and improved the fracture toughness due to inhibit crack propagation. The pore appeared at the interface between WC particles, and the matrix phase had introduced an increase in porosity. With the increase in Co content, the cohesion between matrix friction and WC particles increased and then decreased the porosity (from 0.99% to 0.84%) and surface roughness (Ra from 4.49 to 2.47 μm). It can be concluded that the hardness had decreased (from 1181 to 1120 HV0.3) with a decrease in WC hard phase content. On the contrary, the fracture toughness increased (from 4.57 to 4.64 MPa∙m1/2) due to higher energy absorption in the matrix phase. The WC-12Co and WC-17Co coatings with higher hardness and fracture toughness exhibited better CE resistance than the cobalt-based alloy coating, increasing more than 20% and 16%, respectively. Especially, the WC-12Co coating possessed the best CE resistance and is expected to be applicable in the hydraulic machineries.

scholarly journals Development of Chlorhexidine Loaded Halloysite Nanotube Based Experimental Resin Composite with Enhanced Physico-Mechanical and Biological Properties for Dental Applications

2020 ◽  
Vol 4 (2) ◽  
pp. 81 ◽  
Author(s):  
Tejas Barot ◽  
Deepak Rawtani ◽  
Pratik Kulkarni
Keyword(s):  
Mechanical Properties ◽  
Resin Composite ◽  
Biological Properties ◽  
Degree Of Conversion ◽  
Dental Composites ◽  
Resin Composites ◽  
Dental Resin ◽  
Dental Resin Composites ◽  
Mass Fractions ◽  
Nih 3T3

Objective: The objective of this study was to explore the effect of Chlorhexidine-loaded Halloysite nanotubes (HNT/CHX) fillers (diverse mass fractions from 1 to 10 wt.%) on physicochemical, morphological and biological properties of newly developed experimental dental resin composite, in order to compare with the properties of composites composed of conventional glass fillers. Methods: The dental resin composites were prepared by incorporating various proportions of HNT/CHX. Six different groups of specimens: control group and five groups composed of varied mass fractions of HNT/CHX (e.g., 1.0, 2.5, 5.0, 7.5 and 10 wt.%) as fillers in each group were fabricated. Mechanical properties of the composites were monitored, using UTM. The degree of conversion of dental resin composites and their depth of cure were also evaluated. Antimicrobial properties of dental composites were studied in vitro by applying agar diffusion test on strain Streptococcus mutans and cytotoxicity were studied using NIH-3T3 cell line. Results: The incorporation of varied mass fractions (1.0 to 5.0 wt.%) of HNT/CHX in dental resins composites enhanced mechanical properties considerably with significant antibacterial activity. The slight decrease in curing depth and degree of conversion values of composites indicates its durability. No cytotoxicity was noticed on NIH-3T3 cell lines. Significance: Consistent distribution of HNT/CHX as a filler into dental composites could substantially improve not only mechanical properties but also biological properties of dental composites.

Sign in / Sign up

Export Citation Format

Share Document