scholarly journals Research on Influential Mechanism of HAZ Impact Toughness for Shipbuilding Steel with Mg Addition

Metals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 584 ◽  
Author(s):  
Hui-rong Li ◽  
Li-gen Sun ◽  
Li-guang Zhu ◽  
Yun-song Liu ◽  
Yun-gang Li
Keyword(s):  
Impact Toughness ◽  
Heat Input ◽  
Steel Plates ◽  
Heat Affect Zone ◽  
Shipbuilding Steel ◽  
Welding Heat Input ◽  
Large Heat ◽  
Mg Addition ◽  
The Difference ◽  
The Impact

The welding performance of shipbuilding steel under large heat input could be improved greatly by the addition of Mg to the steel, but the impact toughness of the heat affect zone (HAZ) is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced much intragranular acicular ferrite (IAF); with Mg addition, the inclusion dimension had been reduced effectively, and the IAF-induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant; considering the influence of welding heat input and metallographic microstructure on the impact toughness of HAZ, the welding heat load had a far greater effect than the metallographic microstructure on ductile–brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

scholarly journals Research on Influential Mechanism of HAZ Impact Toughness for Ship-building Steel with Mg Addition

2018 ◽  
Author(s):  
Huirong Li ◽  
Ligen Sun ◽  
Liguang Zhu ◽  
Yunsong Liu ◽  
Yungang Li
Keyword(s):  
Impact Toughness ◽  
Heat Input ◽  
Steel Plates ◽  
Pinning Effect ◽  
Welding Heat Input ◽  
Ductile Brittle Transition Temperature ◽  
Large Heat ◽  
Mg Addition ◽  
The Difference ◽  
The Impact

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Effects of Zirconium on Impact Toughness for the Hull Structure Steel Plate

2014 ◽  
Vol 644-650 ◽  
pp. 4932-4935
Author(s):  
Tie Li Qi
Keyword(s):  
Impact Toughness ◽  
Impact Energy ◽  
Heat Input ◽  
Steel Plate ◽  
Sharp Decline ◽  
Large Size ◽  
Welding Heat Input ◽  
Hull Structure ◽  
Large Heat ◽  
The Impact

The Gleeble3500 combined with SEM, TEM and other experimental methods are employed in this paper to investigate the effects of zirconium content on impact toughness of heat affected zone (HAZ) of hull structure steel plate during the large heat input welding. The results showed when 0.01% zirconium were added in the steel, the impact energy reached 224 J at-60°C experienced 150 kJ/cm welding heat input. But the large-size rectangular inclusions are found in CGHAZ when 0.02% zirconium were added in the steel, the impact energy fell to 38 J at-60°C experienced 150 kJ/cm welding heat input, the large-size inclusions, especially rectangular inclusion, were the main cause for the sharp decline of low temperature toughness after welding.

Microstructure and Toughness of Weld CGHAZ Under Different Heat Input for X90 High Strength Pipeline Steel

2016 ◽  
Author(s):  
Liuqing Yang ◽  
Yongli Sui ◽  
PeiPei Xia ◽  
Die Yang ◽  
Yongqing Zhang
Keyword(s):  
Impact Toughness ◽  
Impact Energy ◽  
Heat Input ◽  
Pipeline Steel ◽  
Charpy Impact ◽  
Optical Microscope ◽  
Granular Bainite ◽  
Alloy Content ◽  
Welding Heat Input ◽  
The Impact

Two kinds of industry trial X90 pipeline steel which had different chemical composition were chosen as experimental materials, and the grain coarsening, microstructure evolution characteristics and the variation rules of low-temperature impact toughness in weld CGHAZ of this two steel under different welding heat input were studied by physical thermal simulation technology, SEM, optical microscope and Charpy impact test. The results show that microstructure in weld CGHAZ of 1# steel is mainly bainite ferrite (BF) and most of the M/A constituents are blocky or short rod-like; the grains of 2# steel are coarse and there is much granular bainite (GB), meanwhile M/A constituents become coarse and their morphology is changing from block to elongated laths; alloy content of X90 pipeline steel under different welding heat input has great effect on the grain size of original austenite, and when heat input is lower than 2.0KJ/mm, Charpy impact toughness in CGHAZ of lower alloy content pipeline steel is good; as heat input increases, impact toughness in CGHAZ of 1# steel is on the rise, and it is high (between 260J and 300J) when heat input is between 2.0KJ/mm and 2.5KJ/mm and the scatter of impact energy is small; impact toughness of 2# steel decreases gradually and the impact energy has obvious variability.

scholarly journals Significant Influence of Welding Heat Input on the Microstructural Characteristics and Mechanical Properties of the Simulated CGHAZ in High Nitrogen V-Alloyed Steel

2020 ◽  
Vol 39 (1) ◽  
pp. 33-44
Author(s):  
Jing Zhang ◽  
Wenbin Xin ◽  
Guoping Luo ◽  
Ruifen Wang ◽  
Qingyong Meng
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Heat Input ◽  
Prior Austenite ◽  
Alloyed Steel ◽  
Coarse Grained ◽  
High Nitrogen ◽  
Microstructural Characteristics ◽  
Welding Heat Input ◽  
The Impact

AbstractThe microstructural characteristics and mechanical properties of the simulated coarse grained heat affected zone (CGHAZ) in high N V-alloyed steel have been conducted under different welding heat input, characterized by the cooling time taken from 800°C to 500°C (t8/5). The experimental results show that the microstructure is dominantly composed of lath bainite (LB) and granular bainite (GB) at t8/5 30 s– 90 s. The content of LB decreases with t8/5 increasing, and that of GB increases. When t8/5 further increases to 120 s and 180 s, the microstructure mainly consists of intragranular polygonal ferrite (IPF) and acicular ferrite (IAF). The higher t8/5 leads to the increased content of intragranular ferrite (IGF). Meanwhile, the prior austenite grain size (PAGS) progressively increases from 56 ± 6.0 μm to 148 ± 9.9 μm as t8/5 increases from 30 s to 180 s. Besides, EBSD analysis indicates that the fraction of high angle grain boundaries (HAGBs) is 0.570, 0.427 and 0.624, respectively, corresponding to t8/5 30, 90 and 180 s. Moreover, the impact toughness decreases as t8/5 increases from 30 s to 90 s caused by the increased PAGS and GB content, and then sharply increases with t8/5 exceeding 90 s due to the increased formation of IGF, especially IAF. Furthermore, the high nitrogen content accelerates V(C,N) precipitation, which not only inhibits the coarsening of prior austenite grains, but promotes the formation of IGF, resulting in the increased number of HAGBs and raising impact toughness.

scholarly journals Effect of Welding Heat Input on Microstructure and Impact Toughness in the Simulated CGHAZ of Low Carbon Mo-V-Ti-N-B Steel

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1997
Author(s):  
Mingliang Qiao ◽  
Huibing Fan ◽  
Genhao Shi ◽  
Leping Wang ◽  
Qiuming Wang ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Heat Input ◽  
Acicular Ferrite ◽  
Granular Bainite ◽  
Equivalent Diameter ◽  
Low Carbon ◽  
Welding Heat Input ◽  
Lath Bainite ◽  
Gleeble 3500 ◽  
The Impact

Welding thermal cycles with heat inputs ranging from 25 to 75 kJ/cm were performed on a Gleeble 3500. The impact energy improved significantly (from 10 to 112 J), whereas the simulated coarse-grain heat-affected zone (CGHAZ) microstructure changed from lath bainite ferrite (LBF) and granular bainite ferrite (GBF) + martensite/austenite (M/A) to acicular ferrite (AF) + polygonal ferrite (PF) + M/A as the heat input increased. Simultaneously, the mean coarse precipitate sizes and the degree of V(C,N) enrichment on the precipitate surface increased, which provided favorable conditions for intragranular ferrite nucleation. The Ar3 of CGHAZ increased from 593 °C to 793 °C with increasing heat inputs; the longer high-temperature residence time inhibited the bainite transformation and promoted the ferrite transformation. As a result, acicular ferrite increased and bainite decreased in the CGHAZ. The CGHAZ microstructure was refined for the acicular ferrite segmentation of the prior austenite, and the microstructure mean equivalent diameter (MED) in the CGHAZ decreased from 7.6 µm to 4.2 µm; the densities of grain boundaries higher than 15° increased from 20.3% to 45.5% and significantly increased the impact toughness. The correlation of heat input, microstructure, and impact toughness was investigated in detail. These results may provide new ideas for the development of high welding heat input multiphase steels.

Effects of oxygen content on microstructure and impact toughness of high heat input flux-cored wire weld metals

2018 ◽  
Vol 115 (4) ◽  
pp. 410
Author(s):  
Fengyu Song ◽  
Yanmei Li ◽  
Ping Wang ◽  
Fuxian Zhu
Keyword(s):  
Grain Size ◽  
Impact Toughness ◽  
Weld Metal ◽  
Oxygen Content ◽  
Heat Input ◽  
High Heat ◽  
Cored Wire ◽  
Weld Metals ◽  
High Heat Input ◽  
The Impact

Three weld metals with different oxygen contents were developed. The influence of oxygen contents on the microstructure and impact toughness of weld metal was investigated through high heat input welding tests. The results showed that a large number of fine inclusions were formed and distributed randomly in the weld metal with oxygen content of 500 ppm under the heat input condition of 341 kJ/cm. Substantial cross interlocked acicular ferritic grains were induced to generate in the vicinity of the inclusions, primarily leading to the high impact toughness at low temperature for the weld metal. With the increase of oxygen content, the number of fine inclusions distributed in the weld metal increased and the grain size of intragranular acicular ferrites decreased, which enhanced the impact toughness of the weld metal. Nevertheless, a further increase of oxygen content would contribute to a great diminution of the austenitic grain size. Following that the fraction of grain boundary and the start temperature of transformation increased, which facilitated the abundant formation of pro-eutectoid ferrites and resulted in a deteriorative impact toughness of the weld metal.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

Effect of Ti, Al and Mg Addition on the Impact Toughness of Heat Affected Zone in Low Carbon Steel

2009 ◽  
Vol 79-82 ◽  
pp. 143-146
Author(s):  
Jiang Hua Ma ◽  
Dong Ping Zhan ◽  
Zhou Hua Jiang ◽  
Ji Cheng He
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Low Carbon Steel ◽  
Optical Microscope ◽  
Carbon Steels ◽  
Low Carbon ◽  
Welding Simulation ◽  
Mg Addition ◽  
The Impact

In order to understand the effects of deoxidizer such as aluminium, titanium and magnesium on the impact toughness of heat affected zone (HAZ), three low carbon steels deoxidized by Ti-Al, Mg and Ti-Mg were obtained. After smelting, forging, rolling and welding simulation, the effects of Al, Ti and Mg addition on the impact toughness of HAZ in low carbon steel were studied. The inclusion characteristics (size, morphology and chemistry) of samples before welding and the fracture pattern of the specimens after the Charpy-type test were respectively analyzed using optical microscope and scanning electron microscopy (SEM). The following results were found. The density of inclusion in Ti-Mg deoxidized steel is bigger than Ti-Al deoxidized steel. The average diameter is decreased for the former than the latter. The addition of Ti-Mg can enhance the impact toughness of the HAZ after welding simulation. The maximal value of the impact toughness is 66.5J/cm2. The complex particles of MgO-TiOx-SiO2-MnS are most benefit to enhance impact toughness. The improvement of HAZ is attributable to the role of particle pinning and the formation of intergranular ferrite.

Impact Toughness Characteristics of SM570-TMC Steel Joint Using Welding Wire Containing 0.4% Nickel at Different Level of Heat Input

2020 ◽  
Vol 867 ◽  
pp. 117-124
Author(s):  
Herry Oktadinata ◽  
Winarto Winarto ◽  
Dedi Priadi ◽  
Eddy S. Siradj ◽  
Ario S. Baskoro
Keyword(s):  
Impact Toughness ◽  
Heat Input ◽  
High Heat ◽  
Optical Microscope ◽  
Butt Joint ◽  
Welding Wire ◽  
Steel Joint ◽  
Microstructure Observation ◽  
High Heat Input ◽  
The Impact

The study was conducted to evaluate the impact toughness of flux-cored arc welded of SM570-TMC steel joint under different heat inputs, 0.9 kJ/mm (low heat input) and 1.6 kJ/mm (high heat input). Welding wire containing 0.4%Ni was selected on this experiment. Multi-pass welds were performed on SM570-TMC steel plate of 16 mm in thickness with a single V-groove butt joint on flat position (1G). The evaluation consists of observations on microstructure using an optical microscope and SEM-EDS, and mechanical properties including tensile, microhardness Vickers and Charpy V-notch (CVN) impact test at temperatures of 25, 0 and-20 °C. Results showed that the impact toughness of the base metal (BM) was higher than the weld metal (WM) at all test temperatures. Hardness and impact toughness of WM at low heat input was observed higher than when applied a high heat input. The welded samples at low and high heat inputs had high of tensile strength, and the fracture seemly occurs on the BM. Microstructure observation showed that at a high heat input, larger grains and microsegregation were observed. It might affect on decreasing their impact property.

Sign in / Sign up

Export Citation Format

Share Document