Mineralogical Appraisal of Bauxite Overburdens from Brazil

Mineralogical appraisal is an important tool for both mining and industrial processes. X-ray powder diffraction analysis (XRPD) can deliver fast and reliable mineralogical quantification results to aid industrial processes and improve ore recoveries. Furthermore, X-ray fluorescence (XRF) chemical data, thermal analysis (TA), and Fourier-transformed infrared spectroscopy (FTIR) can be used to validate and refine XRPD results. Mineralogical assessment of non-traditional ores, such as mining wastes, is also an important step to consider them for near-future industries. In the Brazilian Amazon, alumina-rich clays cover the largest and most important bauxitic deposits of the region and have been considered as a possible raw material for the local cement and ceramic industry. In this work, a mineralogical evaluation of these clays (Belterra Clays) is performed using XRPD, XRF, TA, and FTIR. XRPD-Rietveld quantification confirmed that kaolinite is the main phase of the clay overburden, followed by variable contents of gibbsite and goethite and minor quantities of hematite, anatase, and quartz. The chemistry derived from Rietveld, based on stoichiometric phase compositions, presents a good correlation with the XRF data and is also supported by the TA and FTIR data. The initially assumed homogeneous composition of Belterra Clay is revealed to be variable by the present mineralogical study.

Download Full-text

Characterization of bentonite clay from 'Greda' deposit

Processing and Application of Ceramics ◽

10.2298/pac1102097s ◽

2011 ◽

Vol 5 (2) ◽

pp. 97-101 ◽

Cited By ~ 15

Author(s):

Nadezda Stankovic ◽

Mihovil Logar ◽

Jelena Lukovic ◽

Jelena Pantic ◽

Miljana Miljevic ◽

...

Keyword(s):

Ceramic Industry ◽

Bentonite Clay ◽

Nitrogen Adsorption ◽

Raw Material ◽

X Ray Diffraction ◽

High Quality ◽

X Ray ◽

High Silica ◽

Representative Samples

Based on mineralogical and technological investigations of the deposit 'Greda' important characteristics of bentonite clay were determined. Representative samples of the deposit were characterized with X-ray diffraction, low-temperature nitrogen adsorption, chemical analysis, differential thermal analysis and scanning electron microscopy. It was determined that the main mineral is montmorillonite and in subordinate quantities kaolinite, quartz and pyrite. The chemical composition generally shows high silica and alumina contents in all samples and small quantities of Fe3+, Ca2+ and Mg2+ cations. Based on technological and mineralogical research, bentonite from this deposit is a high-quality raw material for use in the ceramic industry.

Download Full-text

UHMWPE Modified Sodium Alginate

Materials Science Forum ◽

10.4028/www.scientific.net/msf.812.101 ◽

2015 ◽

Vol 812 ◽

pp. 101-106

Author(s):

Mariann Kollár ◽

Gabriella Zsoldos ◽

Tamás Szabó

Keyword(s):

Sodium Alginate ◽

Healing Process ◽

Raw Material ◽

Second Step ◽

Prosthetic Material ◽

Chemical Reagent ◽

X Ray ◽

Fourier Transformed Infrared Spectroscopy ◽

Ca Ions ◽

Na Ions

Aim of our experiments was to modify prosthetic material UHMWPE powder using sodium alginate. The sodium alginate has an important property that the appropriate chemical reagent could exchange its Na+ions to Ca2+ions. The Ca has important role in the healing process, so modifying this substance the UHMWPE material helps patients healing. In the first step we examined that the raw material UHMWPE powder is necessary to be treated in order to adhere alginate at the surface of the UHMWPE powder. In a second step, we examined that insoluble Ca alginate coating left at the surface of UHMWPE powder after the exchange of Na ions. The treated powders were analyzed by Fourier Transformed Infrared Spectroscopy and Diffential Scanning Calorymetry methods. SEM investigations were carried out on the prepared samples moreover energy-dispersive X-ray spectroscopy (EDAX) measurements were performed,-for detection of the presence of small amounts of Na and Ca ions. It has been found that the complex and complicated Caro’s acid chemical treatment is unnecessary in order to prepare alginate coated substrates. The best results were achieved by selecting the correct order of surface layer preparation; first coating the substrate with alginate solution then treating with aqueous CaCl2.

Download Full-text

Mining Wastes of an Albite Deposit as Raw Materials for Vitrified Mullite Ceramics

Minerals ◽

10.3390/min11030232 ◽

2021 ◽

Vol 11 (3) ◽

pp. 232

Author(s):

Pedro J. Sánchez-Soto ◽

Eduardo Garzón ◽

Luis Pérez-Villarejo ◽

George N. Angelopoulos ◽

Dolores Eliche-Quesada

Keyword(s):

Particle Size ◽

Raw Materials ◽

Phase Evolution ◽

Particle Size Analysis ◽

Size Analysis ◽

Mining Wastes ◽

X Ray Diffraction ◽

X Ray ◽

Maximum Value

In this work, an examination of mining wastes of an albite deposit in south Spain was carried out using X-ray Fluorescence (XRF), X-ray diffraction (XRD), particle size analysis, thermo-dilatometry and Differential Thermal Analysis (DTA) and Thermogravimetric (TG) analysis, followed by the determination of the main ceramic properties. The albite content in two selected samples was high (65–40 wt. %), accompanied by quartz (25–40 wt. %) and other minor minerals identified by XRD, mainly kaolinite, in agreement with the high content of silica and alumina determined by XRF. The content of Na2O was in the range 5.44–3.09 wt. %, being associated with albite. The iron content was very low (<0.75 wt. %). The kaolinite content in the waste was estimated from ~8 to 32 wt. %. The particle size analysis indicated values of 11–31 wt. % of particles <63 µm. The ceramic properties of fired samples (1000–1350 °C) showed progressive shrinkage by the thermal effect, with water absorption and open porosity almost at zero at 1200–1250 °C. At 1200 °C, the bulk density reached a maximum value of 2.38 g/cm3. An abrupt change in the phase evolution by XRD was found from 1150 to 1200 °C, with the disappearance of albite by melting in accordance with the predictions of the phase diagram SiO2-Al2O3-Na2O and the system albite-quartz. These fired materials contained as main crystalline phases quartz and mullite. Quartz was present in the raw samples and mullite was formed by decomposition of kaolinite. The observation of mullite forming needle-shape crystals was revealed by Scanning Electron Microscopy (SEM). The formation of fully densified and vitrified mullite materials by firing treatments was demonstrated.

Download Full-text

Study on Adsorption Properties of Modified Corn Cob Activated Carbon for Mercury Ion

Energies ◽

10.3390/en14154483 ◽

2021 ◽

Vol 14 (15) ◽

pp. 4483

Author(s):

Yuyingnan Liu ◽

Xinrui Xu ◽

Bin Qu ◽

Xiaofeng Liu ◽

Weiming Yi ◽

...

Keyword(s):

Activated Carbon ◽

Photoelectron Spectroscopy ◽

Adsorption Process ◽

Physical Adsorption ◽

Raw Material ◽

Order Kinetic ◽

Mercury Ions ◽

Corn Cob ◽

Adsorption Time ◽

X Ray

In this study, corn cob was used as raw material and modified methods employing KOH and KMnO4 were used to prepare activated carbon with high adsorption capacity for mercury ions. Experiments on the effects of different influencing factors on the adsorption of mercury ions were undertaken. The results showed that when modified with KOH, the optimal adsorption time was 120 min, the optimum pH was 4; when modified with KMnO4, the optimal adsorption time was 60 min, the optimal pH was 3, and the optimal amount of adsorbent and the initial concentration were both 0.40 g/L and 100 mg/L under both modified conditions. The adsorption process conforms to the pseudo-second-order kinetic model and Langmuir model. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and Zeta potential characterization results showed that the adsorption process is mainly physical adsorption, surface complexation and ion exchange.

Download Full-text

Cotton stalk-derived hydrothermal carbon for methylene blue dye removal: investigation of the raw material plant tissues

Bioresources and Bioprocessing ◽

10.1186/s40643-021-00364-8 ◽

2021 ◽

Vol 8 (1) ◽

Author(s):

Libo Zhang ◽

Junyan Tan ◽

Gangying Xing ◽

Xintong Dou ◽

Xuqiang Guo

Keyword(s):

Methylene Blue ◽

Functional Materials ◽

Raw Material ◽

Plant Tissues ◽

Chemical Compositions ◽

Waste Biomass ◽

Cotton Stalk ◽

Acid Base ◽

X Ray ◽

Bet Analysis

AbstractConversion of the abundant agricultural residual cotton stalk (CS) into useful chemicals or functional materials could alleviate the fossil fuels caused energy shortages and environmental crises. Although some advances have been achieved, less attention has been paid to the plant tissues effect. In this study, the plant tissue of CS was changed by part degradation of some components (hemicelluloses and lignin, for example) with the aid of acid/base (or both). The pretreated CS was transformed into hydrochar by hydrothermal carbonization (HTC) method. Morphological and chemical compositions of CS hydrochar were analyzed by various techniques, including elemental analysis, Fourier transform infrared (FTIR), BET analysis, X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Methylene blue (MB) removal of prepared CS hydrochar was used to evaluate CS hydrochar pollutions adsorption capacity. Results reveal acid/base (or both) pretreatment is beneficial for CS raw material to prepare high-quality CS hydrochar. The effects of some parameters, such as initial MB concentration, temperature, pH value and recyclability on the adsorption of MB onto both acid and base-pretreated CS hydrochar (CS-H2SO4 + NaOH-HTC) were studied. The present work exhibits the importance of agricultural waste biomass material plant tissues on its derived materials, which will have a positive effect on the direct utilization of waste biomass.

Download Full-text

Geochemistry and Mineralogy of Ice-Dammed Lake Sediments of the Lębork Deposit

Clays and Clay Minerals ◽

10.1007/s42860-021-00129-6 ◽

2021 ◽

Author(s):

Radosław Rogoziński ◽

Alina Maciejewska

Keyword(s):

Chemical Composition ◽

Lake Sediments ◽

Inductively Coupled Plasma ◽

Mineralogical Composition ◽

Raw Material ◽

Element Analysis ◽

X Ray ◽

Dominant Component ◽

Clay Deposits ◽

Dammed Lake

AbstractVarved clay deposits from ice-dammed lakes are a particularly important and broadly applied raw material used for the production of high-quality ceramics (red bricks, roof tiles, etc.), but the mineralogy and geochemistry of these sediments are not fully understood. The aim of the present study was to determine the chemical and mineralogical composition of ice-dammed lake sediments of the Lębork deposit. Major-element analysis of the compositions of selected samples from the ice-dammed lake clays was performed by X-ray fluorescence (XRF) and trace elements were determined by inductively coupled plasma-mass spectrometry. The mineralogical composition of clay samples was determined by X-ray diffraction (XRD). Analyses of the chemical composition of the ice-dammed lake clays of the Lębork deposit showed that the dominant component was SiO2 with a mean content of 56.13 wt.%; the second most abundant component was Al2O3, with a mean content for the entire deposit of 11.61 wt.%. Analysis by ICP-MS indicated the presence of rare earth elements (REE), e.g. cerium, neodymium, lanthanum, and praseodymium; their mean contents are: 56.9, 27.0, 26.3, and 7.3 ppm, respectively. Mineralogical analysis of the varved clays identified quartz, muscovite, calcite, and clay minerals – illite, kaolinite, and montmorillonite. The material filling the Lębork basin is characterized by small lateral and vertical variability in chemical composition. The results of the present study may be of considerable importance in determining the parent igneous, metamorphic, and sedimentary rocks, the weathering products of which supplied material to the ice-dammed lake, as well as in determining the mechanisms and character of the sedimentation process itself.

Download Full-text

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.849.113 ◽

2020 ◽

Vol 849 ◽

pp. 113-118

Author(s):

Yayat Iman Supriyatna ◽

Slamet Sumardi ◽

Widi Astuti ◽

Athessia N. Nainggolan ◽

Ajeng W. Ismail ◽

...

Keyword(s):

Food Packaging ◽

Xrd Analysis ◽

Major Elements ◽

Raw Material ◽

Solid Residue ◽

X Ray Diffraction ◽

X Ray ◽

Leaching Solution ◽

Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Download Full-text

RECYCLING OF MASONRY DEBRIS AS A RAW MATERIAL IN THE CERAMIC INDUSTRY

Challenges of Concrete Construction: Volume 5, Sustainable Concrete Construction ◽

10.1680/scc.31777.0030 ◽

2002 ◽

pp. 291-304 ◽

Cited By ~ 1

Author(s):

K van Dijk ◽

A L A Fraaij ◽

Ch F Hendriks ◽

E Mulder ◽

J van der Zwan

Keyword(s):

Ceramic Industry ◽

Raw Material

Download Full-text

Sedimentary Clays as Geopolymer Precursor

International Journal of Engineering Research in Africa ◽

10.4028/www.scientific.net/jera.39.97 ◽

2018 ◽

Vol 39 ◽

pp. 97-111

Author(s):

F. Mostefa ◽

Nasr Eddine Bouhamou ◽

H.A. Mesbah ◽

Salima Aggoun ◽

D. Mekhatria

Keyword(s):

Sodium Hydroxide ◽

Mineralogical Composition ◽

Cementitious Materials ◽

Raw Material ◽

X Ray Diffraction ◽

Calcination Time ◽

Calorimetric Analysis ◽

X Ray ◽

Before And After ◽

Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Download Full-text

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.620.314 ◽

2012 ◽

Vol 620 ◽

pp. 314-319

Author(s):

Nur Amira Mamat Razali ◽

Fauziah Abdul Aziz ◽

Saadah Abdul Rahman

Keyword(s):

Electron Microscopy ◽

Scanning Electron Microscopy ◽

Alkaline Treatment ◽

Raw Material ◽

X Ray Diffraction ◽

X Ray ◽

Preliminary Preparation ◽

Characterization Studies ◽

Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Download Full-text