scholarly journals Kaolinite Claystone-Based Geopolymer Materials: Effect of Chemical Composition and Curing Conditions

Minerals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 444 ◽  
Author(s):  
Pavlína Hájková
Keyword(s):  
Chemical Composition ◽  
Water Glass ◽  
Chemical Elements ◽  
Solidification Process ◽  
Ease Of Use ◽  
Raw Material ◽  
Curing Conditions ◽  
Low Viscosity ◽  
Lower Porosity ◽  
Curing Methods

This work describes the role of chemical composition and curing conditions in geopolymer strength, leachability of chemical elements and porosity. The study focuses on geopolymer material prepared from calcined kaolinite claystone, which is not studied frequently as a raw material for geopolymer production, although it has a high application potential as it is easily commercially available and allows preparation of geopolymers with low viscosity. The composition of geopolymers and their curing methods were selected considering their ease of use in the praxis. Therefore, the potassium water glass itself was used as alkali activator without any KOH or NaOH addition. Chemical composition was changed only by the density of water glass in the range of 1.2 to 1.6 g·cm−3. Geopolymers were cured at a temperature within the range of 5 °C–70 °C to speed up the solidification process as well as by microwave radiation. High compressive strengths were obtained for geopolymers with the highest densities of the water glass (1.5 and 1.6 g·cm−3) in dependence on various curing conditions. Higher strengths were achieved in the case of samples where the solidification was not accelerated. The samples cured at lower temperatures (5 °C) showed lower porosity compared to the other curing types. The lowest leachability of Si and alkalis was reached for the samples with water glass density 1.5 g·cm−3.

scholarly journals Synthesis and Hydration Characteristic of Geopolymer Based on Lead Smelting Slag

2020 ◽  
Vol 17 (8) ◽  
pp. 2762
Author(s):  
Liwei Yao ◽  
Degang Liu ◽  
Yong Ke ◽  
Yuancheng Li ◽  
Zhongbing Wang ◽  
...  
Keyword(s):  
Water Glass ◽  
Glass Network ◽  
High Energy ◽  
Raw Material ◽  
Alkali Activation ◽  
Curing Conditions ◽  
Industrial Solid Waste ◽  
Process Characteristics ◽  
Lead Smelting ◽  
Smelting Slag

Lead smelting slag (LSS) has been identified as general industrial solid waste, which is produced from the pyrometallurgical treatment of the Shuikoushan process for primary lead production in China. The LSS-based geopolymer was synthesized after high-energy ball milling. The effect of unconfined compressive strength (UCS) on the synthesis parameters of the geopolymer was optimized. Under the best parameters of the geopolymer (modulus of water glass was 1–1.5, dosage of water glass (W(SiO2+Na2O)) was 5% and water-to-binder ratio was 0.2), the UCS reached 76.09 MPa after curing for 28 days. The toxicity characteristic leaching procedure (TCLP) leaching concentration of Zn from LSS fell from 167.16 to 93.99 mg/L after alkali-activation, which was below the limit allowed. Meanwhile, C-S-H and the geopolymer of the hydration products were identified from the geopolymer. In addition, the behavior of iron was also discussed. Then, the hydration process characteristics of the LSS-based geopolymer were proposed. The obtained results showed that Ca2+ and Fe2+ occupied the site of the network as modifiers in the glass phase and then dissociated from the glass network after the water glass activation. At the same time, C-S-H, the geopolymer and Fe(OH)2 gel were produced, and then the Fe(OH)2 was easily oxidized to Fe(OH)3 under the air curing conditions. Consequently, the conclusion was drawn that LSS was an implementable raw material for geopolymer production.

CHEMICAL COMPOSITION OF OAT GRAINS OF ULOV AND VYATSKIY VARIETIES

10.12737/3825 ◽  
2014 ◽  
Vol 9 (1) ◽  
pp. 126-129 ◽  
Author(s):  
Фатыхов ◽  
Ildus Fatykhov ◽  
Колесникова ◽  
Vera Kolesnikova ◽  
Тихонова ◽  
...  
Keyword(s):  
Chemical Composition ◽  
Food Production ◽  
Chemical Elements ◽  
Weather Conditions ◽  
Vegetation Period ◽  
Raw Material ◽  
Farm Animals ◽  
Economic Significance ◽  
National Economic ◽  
Favorable Weather

Oat grain has a great national economic significance. Firstly, it is a concentrated feed for farm animals. Secondly, it is the raw material for food production, most of all, for baby diet. In this regard, when used for feed purpose or for food production, it is necessary to knowledge the chemical composition of the oat grain. Our results demonstrated that by the content of chemical elements, among 70 species the differences were in membranous and hull-less oats. The grain of membranous oat of Ulov variety contained more silicon, potassium and calcium, comparing with the content of hull-less oat grains of Vyatkskiy variety. In a relatively favorable weather conditions of 2010 year, the Ulov oat grains contained more boron, sodium, aluminum, potassium, calcium. Vyatskiy hull-less oat grains at relatively favorable weather conditions of 2011 year, have a higher content of magnesium, phosphorus, calcium, manganese and zinc. Chemical composition of Ulov and Vyatskiy oat grain according to the 70 element have differs and depends on the meteorological conditions of the vegetation period. The membranous and hull-less oat grains did not contain heavy metals above the permissible values, regulated by Sanitary rules and norms 2.3.2.1078-01.

PEAS AND PRODUCTS OF ITS PROCESSING OF - NONCONVENTIONAL RAW MATERIAL RESOURCES

2020 ◽  
Author(s):  
D.Y. Bolgova ◽  
◽  
N.A. Tarasenko ◽  
Z.S. Mukhametova ◽  
◽  
...  
Keyword(s):  
Chemical Composition ◽  
Human Health ◽  
Food Production ◽  
Food Industry ◽  
Raw Material ◽  
Plant Proteins ◽  
Material Resources ◽  
The Rich

Nutrition is an important factor that affects human health. The use of plant proteins as various additives in food production has now been actively developed. The rich chemical composition of pea grains determines the possibility of application in the food industry. Peas are characterized by good assimilability and degree of digestion.

scholarly journals Rheological and Microbiological Characteristics of Hops and Hot Trub Particles Formed during Beer Production

Molecules ◽  
2021 ◽  
Vol 26 (3) ◽  
pp. 681
Author(s):  
Monika Sterczyńska ◽  
Marek Zdaniewicz ◽  
Katarzyna Wolny-Koładka
Keyword(s):  
Rheological Properties ◽  
Raw Materials ◽  
Raw Material ◽  
Microbiological Analysis ◽  
Waste Products ◽  
Low Viscosity ◽  
Post Process ◽  
High Shear Rates ◽  
Different Temperatures ◽  
Beer Production

During the production of beer, and especially beer wort, the main wastes are spent grain and hot trub, i.e., the so-called “hot break.” Combined with yeast after fermentation, they represent the most valuable wastes. Hot trub is also one of the most valuable by-products. Studies on the chemical composition of these sediments and their rheological properties as waste products will contribute to their effective disposal and even further use as valuable pharmaceutical and cosmetic raw materials. So far, hot trub has been studied for morphology and particle distribution depending on the raw material composition and beer wort extract. However, there are no preliminary studies on the rheological properties of hot trub and hops. In particular, no attention has yet been paid to the dependence of these properties on the hop variety or different protein sources used. The aim of this study was to examine the effect of different hopping methods on hot trub viscosity and beer wort physicochemical parameters. Additionally, the hop solutions were measured at different temperatures. A microbiological analysis of hop sediments was also performed to determine the post-process survival of selected microorganisms in these wastes. For manufacturers of pumps used in the brewing industry, the most convenient material is that of the lowest viscosity. Low viscosity hot trub can be removed at lower velocities, which reduces costs and simplifies washing and transport. The sediments also had similar equilibrium viscosity values at high shear rates.

scholarly journals Geochemistry and Mineralogy of Ice-Dammed Lake Sediments of the Lębork Deposit

2021 ◽  
Author(s):  
Radosław Rogoziński ◽  
Alina Maciejewska
Keyword(s):  
Chemical Composition ◽  
Lake Sediments ◽  
Inductively Coupled Plasma ◽  
Mineralogical Composition ◽  
Raw Material ◽  
Element Analysis ◽  
X Ray ◽  
Dominant Component ◽  
Clay Deposits ◽  
Dammed Lake

AbstractVarved clay deposits from ice-dammed lakes are a particularly important and broadly applied raw material used for the production of high-quality ceramics (red bricks, roof tiles, etc.), but the mineralogy and geochemistry of these sediments are not fully understood. The aim of the present study was to determine the chemical and mineralogical composition of ice-dammed lake sediments of the Lębork deposit. Major-element analysis of the compositions of selected samples from the ice-dammed lake clays was performed by X-ray fluorescence (XRF) and trace elements were determined by inductively coupled plasma-mass spectrometry. The mineralogical composition of clay samples was determined by X-ray diffraction (XRD). Analyses of the chemical composition of the ice-dammed lake clays of the Lębork deposit showed that the dominant component was SiO2 with a mean content of 56.13 wt.%; the second most abundant component was Al2O3, with a mean content for the entire deposit of 11.61 wt.%. Analysis by ICP-MS indicated the presence of rare earth elements (REE), e.g. cerium, neodymium, lanthanum, and praseodymium; their mean contents are: 56.9, 27.0, 26.3, and 7.3 ppm, respectively. Mineralogical analysis of the varved clays identified quartz, muscovite, calcite, and clay minerals – illite, kaolinite, and montmorillonite. The material filling the Lębork basin is characterized by small lateral and vertical variability in chemical composition. The results of the present study may be of considerable importance in determining the parent igneous, metamorphic, and sedimentary rocks, the weathering products of which supplied material to the ice-dammed lake, as well as in determining the mechanisms and character of the sedimentation process itself.

scholarly journals Chemical Composition of the RS CNn-Type Star 33 Piscium

2011 ◽  
Vol 20 (1) ◽  
Author(s):  
G. Barisevišius ◽  
G. Tautvaišienė ◽  
S. Berdyugina ◽  
Y. Chorniy ◽  
I. Ilyin
Keyword(s):  
Chemical Composition ◽  
Chemical Elements ◽  
Type Star

AbstractAbundances of 22 chemical elements, including the key elements and isotopes such as

scholarly journals An Effective Method for Preparation of Liquid Phosphoric Anhydride and Its Application in Flame Retardant Epoxy Resin

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2205
Author(s):  
Qian Li ◽  
Yujie Li ◽  
Yifan Chen ◽  
Qiang Wu ◽  
Siqun Wang
Keyword(s):  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Oxygen Index ◽  
Decomposition Temperature ◽  
Ease Of Use ◽  
Limiting Oxygen Index ◽  
Good Thermal Stability ◽  
Low Viscosity ◽  
The Impact

A novel liquid phosphorous-containing flame retardant anhydride (LPFA) with low viscosity was synthesized from 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and methyl tetrahydrophthalic anhydride (MeTHPA) and further cured with bisphenol-A epoxy resin E-51 for the preparation of the flame retardant epoxy resins. Both Fourier transform infrared spectroscopy (FT-IR), mass spectrometry (MS) and nuclear magnetic resonance (NMR) measurements revealed the successful incorporation of DOPO on the molecular chains of MeTHPA through chemical reaction. The oxygen index analysis showed that the LPFA-cured epoxy resin exhibited excellent flame retardant performance, and the corresponding limiting oxygen index (LOI) value could reach 31.2%. The UL-94V-0 rating was achieved for the flame retardant epoxy resin with the phosphorus content of 2.7%. With the addition of LPFA, the impact strength of the cured epoxy resins remained almost unchanged, but the flexural strength gradually increased. Meanwhile, all the epoxy resins showed good thermal stability. The glass transition temperature (Tg) and thermal decomposition temperature (Td) of epoxy resin cured by LPFA decreased slightly compared with that of MeTHPA-cured epoxy resin. Based on such excellent flame retardancy, low viscosity at room temperature and ease of use, LPFA showed potential as an appropriate curing agent in the field of electrical insulation materials.

Numerical Simulation of Filling and Solidification in Sand Casting by Procast

2013 ◽  
Vol 791-793 ◽  
pp. 550-553 ◽  
Author(s):  
Dong Dong Han ◽  
Cheng Jun Wang ◽  
Juan Chang ◽  
Lei Chen ◽  
Huai Bei Xie
Keyword(s):  
Numerical Simulation ◽  
Heat Dissipation ◽  
Solidification Process ◽  
Simulation Software ◽  
Sand Casting ◽  
Production Costs ◽  
Raw Material ◽  
Casting Defects ◽  
Three Dimension ◽  
Filling And Solidification

At present, pulley produced in China has been able to meet the demand of domestic and international markets. But there are many problem of the pulley industry in our country, such as too many production enterprises and the low level of export products. And as components of drive system are light weight and raw material price of pulley casting are rising, manufacturing requirements of the pulley are also more and more high. Aiming at the casting defects of pulley that enterprise current product, pulley casting blank model of common material HT250 be made by three-dimension software, numerical simulation of filling and solidification process for pulley sand casting by the casting simulation software Procast, the size and location of the various casting defects were forecasted and analyzed, reflecting the pulley filling and solidification process of the actual situation, due to the thicker pulley rim and less heat dissipation, position of shrinkage is close to the middle of rim [, a method of eliminating defects is proposed to realize sequential solidification, and thus to minimize porosity shrinkage and improve casting performance and reduce casting time and reduce production costs.

scholarly journals Seasonal variations in PM10 inorganic composition in the Andean city

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Rasa Zalakeviciute ◽  
Katiuska Alexandrino ◽  
Yves Rybarczyk ◽  
Alexis Debut ◽  
Karla Vizuete ◽  
...  
Keyword(s):  
Chemical Composition ◽  
Inductively Coupled Plasma ◽  
Chemical Elements ◽  
Large Fraction ◽  
Urban Pollution ◽  
Optical Emission ◽  
High Elevation ◽  
Water Soluble ◽  
Wet Season ◽  
Soluble Ions

Abstract Particulate matter (PM) is one of the key pollutants causing health risks worldwide. While the preoccupation for increased concentrations of these particles mainly depends on their sources and thus chemical composition, some regions are yet not well investigated. In this work the composition of chemical elements of atmospheric PM10 (particles with aerodynamic diameters ≤ 10 µm), collected at the urban and suburban sites in high elevation tropical city, were chemically analysed during the dry and wet seasons of 2017–2018. A large fraction (~ 68%) of PM10 composition in Quito, Ecuador is accounted for by water-soluble ions and 16 elements analysed using UV/VIS spectrophotometer and Inductively Coupled Plasma—Optical Emission Spectroscopy (ICP-OES). Hierarchical clustering analysis was performed to study a correlation between the chemical composition of urban pollution and meteorological parameters. The suburban area displays an increase in PM10 concentrations and natural elemental markers during the dry (increased wind intensity, resuspension of soil dust) season. Meanwhile, densely urbanized area shows increased total PM10 concentrations and anthropogenic elemental markers during the wet season, which may point to the worsened combustion and traffic conditions. This might indicate the prevalence of cardiovascular and respiratory problems in motorized areas of the cities in the developing world.

scholarly journals Soil and Leaf Nutrients Drivers on the Chemical Composition of the Essential Oil of Siparuna muricata (Ruiz & Pav.) A. DC. from Ecuador

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2949
Author(s):  
Juan I. Burneo ◽  
Ángel Benítez ◽  
James Calva ◽  
Pablo Velastegui ◽  
Vladimir Morocho
Keyword(s):  
Gas Chromatography ◽  
Chemical Composition ◽  
Secondary Metabolites ◽  
Essential Oil ◽  
Chemical Elements ◽  
Climatic Conditions ◽  
Gas Chromatography Mass Spectrometry ◽  
Chemical Compositions ◽  
Leaf Nutrients ◽  
First Time

Chemical compositions of plants are affected by the initial nutrient contents in the soil and climatic conditions; thus, we analyzed for the first time the effects of soil and leaf nutrients on the compositions of the essential oils (EOs) of Siparuna muricata in four different localities in Ecuador. EOs were obtained by hydrodistillation and analyzed by gas chromatography/mass spectrometry (GC/MS) and a gas chromatography/flame ionization detector (GC/FID). Enantiomeric distribution by GC/MS was determined, modifying the enantiomeric separation of β-pinene, limonene, δ-elemene, β-bourbonene, cis-cadina-1 (6), 4-diene and atractylone. A total of 44 compounds were identified. The most representative for L1 were guaiol, atractylone and 4-diene; for L2, cis-cadina-1(6),4-diene and myrcene; for L3, atractylone, myrcene and germacrene B; and finally, L4 germacrene B, myrcene and cis-cadina-1(6),4-diene. Correlations between soil- leaf chemical elements such as Al, Ca, Fe, Mg, Mn, N and Si in the different localities were significant with chemical composition of the essential oil of Siparuna muricata; however, correlations between soil and leaf K, P, and Na were not significant. Cluster and NMDS analysis showed high dissimilarity values of secondary metabolites between four localities related with changes in soil- leaf nutrients. Thus, the SIMPER routine revealed that not all secondary metabolites contribute equally to establishing the differences in the four localities, and the largest contributions are due to differences in guaiol, cis-cadina-1(6),4-diene, atractylone and germacrene. Our investigation showed for the first time the influences of altitude and soil- leaf chemical elements in the chemical composition of the EOs of S. muricata.

Sign in / Sign up

Export Citation Format

Share Document