Correlation Detection and Location for Microseismic Events Induced by Hydraulic Fracturing

2012 ◽  
Author(s):  
R. Cieplicki ◽  
L. Eisner ◽  
D. Abbott
Keyword(s):  
Hydraulic Fracturing ◽  
Microseismic Events

Results of the downhole microseismic monitoring at a pilot hydraulic fracturing site in Poland — Part 1: Event location and stimulation performance

2018 ◽  
Vol 6 (3) ◽  
pp. SH39-SH48 ◽  
Author(s):  
Wojciech Gajek ◽  
Jacek Trojanowski ◽  
Michał Malinowski ◽  
Marek Jarosiński ◽  
Marko Riedel
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Anisotropy ◽  
Transverse Isotropy ◽  
Velocity Model ◽  
Microseismic Monitoring ◽  
Baltic Basin ◽  
Hydraulic Stimulation ◽  
Lower Paleozoic ◽  
Event Location ◽  
Microseismic Events

A precise velocity model is necessary to obtain reliable locations of microseismic events, which provide information about the effectiveness of the hydraulic stimulation. Seismic anisotropy plays an important role in microseismic event location by imposing the dependency between wave velocities and its propagation direction. Building an anisotropic velocity model that accounts for that effect allows for more accurate location of microseismic events. We have used downhole microseismic records from a pilot hydraulic fracturing experiment in Lower-Paleozoic shale gas play in the Baltic Basin, Northern Poland, to obtain accurate microseismic events locations. We have developed a workflow for a vertical transverse isotropy velocity model construction when facing a challenging absence of horizontally polarized S-waves in perforation shot data, which carry information about Thomsen’s [Formula: see text] parameter and provide valuable constraints for locating microseismic events. We extract effective [Formula: see text], [Formula: see text] and [Formula: see text], [Formula: see text] for each layer from the P- and SV-wave arrivals of perforation shots, whereas the unresolved [Formula: see text] is retrieved afterward from the SH-SV-wave delay time of selected microseismic events. An inverted velocity model provides more reliable location of microseismic events, which then becomes an essential input for evaluating the hydraulic stimulation job effectiveness in the geomechanical context. We evaluate the influence of the preexisting fracture sets and obliquity between the borehole trajectory and principal horizontal stress direction on the hydraulic treatment performance. The fracturing fluid migrates to previously fractured zones, while the growth of the microseismic volume in consecutive stages is caused by increased penetration of the above-lying lithologic formations.

Role of fracture opening in triggering microseismicity observed during hydraulic fracturing

Geophysics ◽  
2019 ◽  
Vol 84 (3) ◽  
pp. KS105-KS118 ◽  
Author(s):  
Himanshu Barthwal ◽  
Mirko van der Baan
Keyword(s):  
Hydraulic Fracturing ◽  
Pore Pressure ◽  
Material Balance ◽  
Crack Tip ◽  
Hydrocarbon Reservoirs ◽  
Fluid Injection ◽  
Low Permeability ◽  
Stress Shadow ◽  
Pressure Diffusion ◽  
Microseismic Events

Hydraulic fracturing in low-permeability hydrocarbon reservoirs creates/reactivates a fracture network leading to microseismic events. We have developed a simplified model of the evolution of the microseismic cloud based on the opening of a planar fracture cavity and its effect on elastic stresses and pore pressure diffusion during fluid injection in hydraulic fracturing treatments. Using a material balance equation, we compute the crack tip propagation over time assuming that the hydraulic fracture is shaped as a single penny-shaped cavity. Results indicate that in low-permeability formations, the crack tip propagates much faster than the pore pressure diffusion front thereby triggering the microseismic events farthest from the injection domain at any given time during fluid injection. We use the crack tip propagation to explain the triggering front observed in distance versus time plots of published microseismic data examples from hydraulic fracturing treatments of low-permeability hydrocarbon reservoirs. We conclude that attributing the location of the microseismic triggering front purely to pore pressure diffusion from the injection point may lead to incorrect estimates of the hydraulic diffusivity by multiple orders of magnitude for low-permeability formations. Moreover, the opening of the fracture cavity creates stress shadow zones perpendicular to the principal fracture walls in which microseismic triggering due to the elastic stress perturbations is suppressed. Microseismic triggering in this stress shadow region may be attributed mainly to pore pressure diffusion. We use the width, instead of the longest size, of the microseismic cloud to obtain an enhanced diffusivity measure, which may be useful for subsequent production simulations.

Microseismic Magnitudes and b-Values for Delineating Hydraulic Fracturing and Depletion

SPE Journal ◽  
2017 ◽  
Vol 22 (05) ◽  
pp. 1624-1634 ◽  
Author(s):  
T.. Dohmen ◽  
J.. Zhang ◽  
L.. Barker ◽  
J. P. Blangy
Keyword(s):  
Hydraulic Fracturing ◽  
Qualitative Assessment ◽  
Williston Basin ◽  
Oil Well ◽  
B Values ◽  
Relative Contribution ◽  
Microseismic Activity ◽  
Shear Slip ◽  
Microseismic Events ◽  
Well Completions

Summary In 2014, Hess Corporation collected microseismic and hydraulic-fracturing data in a Bakken field trial near an existing oil well in the Williston Basin of North Dakota. In addition to monitoring the microseismic activity of the newly drilled offset-well completions, the field test delineated the depletion surrounding the original well by slowly repressurizing it. This repressurization induced shear-slip events, which preferentially delineated the depleted zone of the producer well, a process we call microseismic depletion delineation (MDD). By comparing the magnitudes of the depletion-related events to those that accompanied the new offset completions, we observe that higher magnitude microseismic events occur within the depleted interval. This paper offers an explanation for why higher magnitudes appear in the depleted zone and suggests that measuring magnitude statistics in the form of b-values can provide a qualitative assessment of the relative contribution of oil from completions along a wellbore.

The role of preexisting fractures and faults during multistage hydraulic fracturing in the Bakken Formation

2014 ◽  
Vol 2 (3) ◽  
pp. SG25-SG39 ◽  
Author(s):  
Yi Yang ◽  
Mark D. Zoback
Keyword(s):  
Hydraulic Fracturing ◽  
Pore Pressure ◽  
Well Being ◽  
Williston Basin ◽  
Bakken Formation ◽  
Multistage Hydraulic Fracturing ◽  
Geomechanical Analysis ◽  
Microseismic Events ◽  
Observation Wells

We performed an integrated study of multistage hydraulic fracture stimulation of two parallel horizontal wells in the Bakken Formation in the Williston Basin, North Dakota. There are three distinct parts of this study: development of a geomechanical model for the study area, interpretation of multiarray downhole recordings of microseismic events, and interpretation of hydraulic fracturing data in a geomechanical context. We estimated the current stress state to be characterized by an NF/SS regime, with [Formula: see text] oriented approximately [Formula: see text]. The microseismic events were recorded in six vertical observation wells during hydraulic fracturing of parallel wells X and Z with three unusual aspects. First, rather than occurring in proximity to the stages being pressurized, many of the events occurred along the length of well Y, a parallel well located between wells X and Z that had been in production for approximately [Formula: see text] years at the time X and Z were stimulated. Second, relatively few fracturing stages were associated with an elongated cloud of events trending in the direction of [Formula: see text] as was commonly observed during hydraulic fracturing. Instead, the microseismic events in a few stages appeared to trend approximately [Formula: see text], approximately 30° from the direction of [Formula: see text]. Earthquake focal plane mechanisms confirmed slip on faults with this orientation. Finally, the microseismic events were clustered at two distinct depths: one near the depth of the well being pressurized in the Middle Bakken Formation and the other approximately [Formula: see text] above in the Mission Canyon Formation. We proposed that steeply dipping N75°E striking faults with a combination of normal and strike-slip movement were being stimulated during hydraulic fracturing and provided conduits for pore pressure to be transmitted to the overlaying formations. We tested a simple geomechanical analysis to illustrate how this occurred in the context of the stress field, pore pressure, and depletion in the vicinity of well Y.

Microseismic search engine for real-time estimation of source location and focal mechanism

Geophysics ◽  
2016 ◽  
Vol 81 (5) ◽  
pp. KS169-KS182 ◽  
Author(s):  
Xiong Zhang ◽  
Jie Zhang
Keyword(s):  
Hydraulic Fracturing ◽  
Real Time ◽  
Search Engine ◽  
Focal Mechanism ◽  
Input Data ◽  
Web Search ◽  
Solution Space ◽  
Web Search Engine ◽  
Fracturing Process ◽  
Microseismic Events

Similar to a web search engine, we have developed a microseismic search engine that can estimate an event location and the focal mechanism in less than a second to monitor the hydraulic fracturing process. The method was extended from a real-time earthquake monitoring approach for seismological applications. We first calculate the full waveforms of all possible microseismic events over a 3D grid with a known velocity model for a given acquisition geometry to create a database. We then index and rank all of the seismic waveforms in the database by following the characteristics of the phase and amplitude of the waveform through a computer fast search technology, specifically, the multiple randomized k-dimensional tree method. When a microseismic event occurs, the approximate best matches to the entry waveform are found immediately by comparing the characteristic features between the input data and the database. The method returns not just one but a series of solutions, similar to a web search engine. Thus, we can obtain a solution space that delineates the resolution and confidence level of the results. Also similar to a web search engine, the microseismic search engine does not require any input parameter or processing experience; thus, the solutions are the same for any user. Numerical tests suggest that the waveform search approach is insensitive to random and correlated noises. However, if the correlation values between the input data and best matches in the database are too low, suggesting unreliable results, the solution may be rejected automatically by applying a preset threshold. We have applied the method to real data, and found great potential for the routine real-time monitoring of microseismic events during hydraulic fracturing.

Lithology-controlled stress variations and pad-scale faults: A case study of hydraulic fracturing in the Woodford Shale, Oklahoma

Geophysics ◽  
2017 ◽  
Vol 82 (6) ◽  
pp. ID35-ID44 ◽  
Author(s):  
Xiaodong Ma ◽  
Mark D. Zoback
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Strike Slip ◽  
Woodford Shale ◽  
Stress Regime ◽  
Component Content ◽  
Microseismic Events ◽  
Minimum Horizontal Stress ◽  
Stress Variations

We have conducted an integrated study to investigate the petrophysical and geomechanical factors controlling the effectiveness of hydraulic fracturing (HF) in four subparallel horizontal wells in the Mississippi Limestone-Woodford Shale (MSSP-WDFD) play in Oklahoma. In two MSSP wells, the minimum horizontal stress [Formula: see text] indicated by the instantaneous shut-in pressures of the HF stages are significantly less than the vertical stress [Formula: see text]. This, combined with observations of drilling-induced tensile fractures in the MSSP in a vertical well at the site, indicates that this formation is in a normal/strike-slip faulting stress regime, consistent with earthquake focal mechanisms and other stress indicators in the area. However, the [Formula: see text] values are systematically higher and vary significantly from stage to stage in two WDFD wells. The stages associated with the abnormally high [Formula: see text] values (close to [Formula: see text]) were associated with little to no proppant placement and a limited number of microseismic events. We used compositional logs to determine the content of compliant components (clay and kerogen). Due to small variations in the trajectories of the horizontal wells, they penetrated three thin, but compositionally distinct WDFD lithofacies. We found that [Formula: see text] along the WDFD horizontals increases when the stage occurred in a zone with high clay and kerogen content. These variations of [Formula: see text] can be explained by various degrees of viscous stress relaxation, which results in the increase in [Formula: see text] (less stress anisotropy), as the compliant component content increases. The distribution of microseismic events was also affected by normal and strike-slip faults cutting across the wells. The locations of these faults were consistent with unusual lineations of microseismic events and were confirmed by 3D seismic data. Thus, the overall effectiveness of HF stimulation in the WDFD wells at this site was strongly affected the abnormally high HF gradients in clay-rich lithofacies and the presence of preexisting, pad-scale faults.

Sign in / Sign up

Export Citation Format

Share Document