Influence of Fly Ash on Thaumasite Form of Sulfate Attack in Cement-Based Materials

2013 ◽  
Vol 377 ◽  
pp. 74-79
Author(s):  
Chang Cheng Li ◽  
Fu Jie Jia ◽  
Xu Nan Wu
Keyword(s):  
Fly Ash ◽  
Activity Index ◽  
Early Stage ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Minor Role ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cement Based Materials ◽  
A Minor

A low temperature sulfate attack research was carried out to investigate the effects of fly ash on thaumasite form of sulfate attack (TSA) in cement-based materials. Cement-limestone-fly ash samples were immerged in 5% magnesium sulfate solution at (5±2) oC. The appearance of samples was observed, and strength was also tested. Besides, the corrosion products were analyzed by infrared spectrum (IR) and X-ray diffraction (XRD) methods. Cement was equally replaced by fly ash with 20%, 30%, and 50% proportions. The results show that: Effects of fly ash on TSA were closely related to the composition, content and fineness of fly ash. Fly ash with an activity index larger than 80% could improve the resistance to TSA in cement-based materials when the replacement reached 50% while fly ash only played a minor role in early stage with 20%-30% content.

scholarly journals Influence of Inertia and Low Active Mineral Admixture on Strength and Microstructure of Cement-Based Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-9
Author(s):  
Meijuan Rao ◽  
Wan Tang ◽  
Wei Zhou ◽  
Yaning Kong ◽  
Shuhua Liu
Keyword(s):  
Fly Ash ◽  
Early Stage ◽  
Heat Of Hydration ◽  
Mineral Admixture ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Inert Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cement Based Materials

Cement-based materials were investigated by comparing the strength and microstructure of pastes and mortar containing limestone powder or low quality fly ash. The compressive strength of the mortar at 28 and 90 d was examined whose microstructures were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis, and differential thermal analysis (TG-DTA). The results indicated that the strength of mortar decreased with increasing mineral admixtures. The limestone powder mainly acted as inert filler and hardly took part in the chemical reaction. Low quality fly ash may accelerate the formation of hydration products in samples with more chemically bonded water. This further resulted in a higher degree of cement hydration and denser microstructure, while the overall heat of hydration was reduced. At the early stage of hydration, low quality fly ash can be considered as an inert material whereas its reactivity at the later stage became high, especially for ground low quality fly ash.

The Effect of Fly Ash on TSA of Cementitous Material: Based on Three Years Results

2013 ◽  
Vol 539 ◽  
pp. 139-144
Author(s):  
Ben Wan Liu ◽  
Chang Hui Yang ◽  
Xiao Bin Xiang ◽  
Lin Wen Yu ◽  
Jing Zhang
Keyword(s):  
Fly Ash ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Hardened Cement ◽  
Hydration Reaction ◽  
X Ray Diffraction ◽  
Hardened Cement Paste ◽  
X Ray ◽  
Ft Ir ◽  
Secondary Hydration

The thaumasite form of sulfate attack of cementitous material (TSA) is a new kind of sulfate attack and it is more harmful than traditional sulfate attack. By means of Fourier transform infrared (FT-IR) and X-ray diffraction (XRD), the effect of dosage and fineness of fly ash on TSA of cementitous material were investigated in this paper. The specimens had been immersed in magnesium sulfate solution of 5% mass concentration at 5±2° C for three years. The results showed that fly ash could not restrain the formation of thaumasite but it delayed the occurrence of TSA in cementitous material when 30% fly ash takes place of cement. Fly ash could enhance the resistance of cementitous material to TSA through secondary hydration reaction to optimizing the pore structure of hardened cement paste and lowering the C/S of C-S-H gel.

Deterioration of concrete containing limestone powder exposed to sulfate attack at ambient temperature

2021 ◽  
Vol 11 (5) ◽  
pp. 724-731
Author(s):  
Hemin Liu ◽  
Qian Huang ◽  
Liang Zhao
Keyword(s):  
Ambient Temperature ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Limestone Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mineral Phases ◽  
Adverse Influence ◽  
Powder Content ◽  
Scanning Electron

This study investigates the deterioration of concrete containing limestone powder exposed to sulfate solution under ambient temperature (20~25 °C). Microstructure and mineral phases within the attacked concrete were measured by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). It was found that the addition of limestone powder increased the initial porosity of concrete. Consequently, a larger amount of SO2–4 ions diffused into the concrete containing limestone powder, and their degree of deterioration caused by sulfate attack increased with the increase in limestone powder content. At ambient temperature, gypsum and ettringite were the major attack products, respectively within the surface and nearsurface portions of concrete containing limestone powder, which was consistent with the products of sulfate attack within concrete without limestone powder. Therefore, the type and distribution of the attack products in concrete had not been revised due to the addition of limestone powder. Nevertheless, the adverse influence of limestone powder on the sulfate resistance of concrete, even at ambient temperature, should be considered. Furthermore, effective measures should be implemented to improve the durability of concrete containing limestone powder in this environment.

Accelerate Thaumasite Formation in Cement-Limestone Powder Paste by Internal Adding Method

2011 ◽  
Vol 250-253 ◽  
pp. 22-27 ◽  
Author(s):  
Chang Cheng Li ◽  
Yan Yao ◽  
Ling Wang
Keyword(s):  
Magnesium Sulfate ◽  
Sodium Sulfate ◽  
Calcium Sulfate ◽  
Sulfate Attack ◽  
Limestone Powder ◽  
Resonance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cement Based Materials ◽  
Internal Sulfate Attack

Cement-limestone powder pastes added with 10% magnesium sulfate, sodium sulfate, and calcium sulfate respectively were stored in water at (5±2) °C to accelerate thaumasite formation. The pastes were inspected visually at intervals. And the formation of thaumasite was identified and confirmed by X-ray diffraction (XRD), infrared spectroscopy (IR), and nuclear magnetic resonance spectroscopy (NMR). The results show that internal adding sulfate in cement-limestone powder paste is an efficient way to accelerate thaumasite formation, and the accelerated effect is magnesium sulfate> sodium sulfate> calcium sulfate. Cement-limestone paste containing 10% magnesium sulfate totally turns into grey-white mushy materials after 6 months immersion, and products are mainly thaumasite and gypsum. In addition, the amount of thaumasite increases along with time of internal sulfate attack in 15 months. XRD, IR, and NMR are powerful and reliable tools for identification of thaumasite in cement-based materials.

Rapid Quantitative Identification of Thaumasite

2013 ◽  
Vol 743-744 ◽  
pp. 186-192 ◽  
Author(s):  
Chang Cheng Li ◽  
Yan Yao ◽  
Ling Wang
Keyword(s):  
Magnesium Sulfate ◽  
Rietveld Refinement ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Limestone Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Identification Method ◽  
Quantitative Identification ◽  
Ir Analysis

To establish a quantitative identification method of thaumasite, internal doping method was used to accelerate thaumasite form of sulfate attack (TSA). A cement-limestone powder paste doped 10% of magnesium sulfate was immersed in water at (5±2) °C, while the blank was in 10% magnesium sulfate solution (by weight). Paste corrosion products were analyzed by infrared spectrum (IR), thermal analysis, nuclear magnetic resonance (NMR), and X-ray diffraction (XRD)/Rietveld refinement methods. The results show that the thaumasite formation was successfully accelerated by internal doping method. A lot of thaumasite formed after 6-15 months low temperature sulfate attack with gray mud-like material. IR analysis is able to be used to analysis thaumasite qualitatively, and Rietveld refinement was suitable to quantitative analysis of thaumasite. A rapid quantitative identification method of thaumasite including visual inspection, IR spectrum and XRD/Rietveld refinement was also established which will improve the accuracy and rapidness of TSAs research.

Effect of Fly Ash on Resistance to Sulfate Attack of Cement-Based Materials

2013 ◽  
Vol 539 ◽  
pp. 124-129 ◽  
Author(s):  
Kai Wei Liu ◽  
Min Deng ◽  
Li Wu Mo
Keyword(s):  
Fly Ash ◽  
Pore Structure ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Length Change ◽  
Sulfate Attack ◽  
Sodium Sulfate Solution ◽  
Reaction Products ◽  
Visual Appearance ◽  
Cement Based Materials

The resistance to sulfate attack of mortars containing 0%, 20%, and 40% of fly ash cured in 5 wt. % sodium sulfate solution at 20°C was investigated in this paper. Visual appearance, cracking analysis, velocity of ultrasonic wave and length change were applied to evaluate the sulfate resistance of mortars. The phases and microstructure of the reaction products due to sulfate attack were examined by XRD and SEM, and the pore structure of the mortars was analyzed by MIP. The effects of fly ash on the sulfate attack of mortars were analyzed. Results indicated that the addition of fly ash improved the resistance of sulfate attack significantly, this probably contributed to the pozzonlanic reaction of fly ash.

scholarly journals Durability properties of ladle slag geopolymer mortar based on fly ash

2020 ◽  
Vol 52 (2) ◽  
pp. 231-243
Author(s):  
Jelena Bijeljic ◽  
Nenad Ristic ◽  
Zoran Grdic ◽  
Gordana Toplicic-Curcic ◽  
Dragan Djordjevic
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Activity Index ◽  
Sodium Hydroxide Solution ◽  
Ultrasound Velocity ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Particle Sizes ◽  
Ambient Conditions ◽  
Ladle Slag

This paper presents the results of tests of physical-mechanical, durability and microscopic properties of geopolymer mortar mixtures based on fly ash and ladle slag. The mixtures are alkali-activated using sodium silicate and sodium hydroxide solution. Firstly, the effects of different fly ash (class ?F?) particle sizes on the characteristics of the mortar mixtures were examined when binder and alkali activator were cured at 95?C for 24 h, also pozzolanic activity and strength activity index were investigated. After that, fly ash ground of optimal particle sizes (0,09 mm) was replaced with ladle slag, 0 to 20% of the mass, the replacement steps being 5%. The specimens having dimensions 4x4x16 cm were then cured in ambient conditions, and the effects of replacement of a part of fly ash with ladle slag were determined by testing water absorption, flexural and compressive strength, freeze-thaw resistance, sulfate attack, ultrasound velocity, FT-IR spectroscopy and leaching of heavy metals. According to the test results of compressive strength resistance of geopolymer mortars exposed to sulfate solution, the mortar made with fly ash and ladle slag showed better resistance to sulfate attack than the mortar made with fly ash only.

Effect of Initial Curing Conditions on Thaumasite Form of Sulfate Attack of Cement Based Materials

2013 ◽  
Vol 275-277 ◽  
pp. 2136-2140 ◽  
Author(s):  
Chang Hui Yang ◽  
Xiao Bin Xiang ◽  
Ben Wan Liu ◽  
Jing Zhang
Keyword(s):  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Sulfate Attack ◽  
X Ray Diffraction ◽  
Hydration Degree ◽  
Humid Air ◽  
Curing Conditions ◽  
X Ray ◽  
Cement Based Materials ◽  
Water Curing

The effects of initial high humid air-curing, standard water-curing and sealed-curing on thaumasite form of sulfate attack (TSA) of cement based materials were studied. The erosion products after three years attack in 5% MgSO4 solution were analyzed by means of X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). Initial high humid air-curing can delay the TSA of specimens for CaCO3 generated by carbonation and filled in the pores of the specimens, forming a compacted surface and restricting the intrusion of SO42-. In comparison, specimens cured in sealed condition occurred TSA most serious resulting from that large amount of inter-defects in specimens for the lower hydration degree, and SO42- ions could intrude into specimens more easily.

scholarly journals Mechanical behavior and durability of mortars with quartzite and Portland cement after sulfate attack

2019 ◽  
Vol 24 (4) ◽  
Author(s):  
Sâmea Valensca Alves Barros ◽  
Gelmires de Araújo Neves ◽  
Romualdo Rodrigues Menezes ◽  
Gerbeson Carlos Batista Dantas ◽  
Patrícia Mendonça Pimentel
Keyword(s):  
Mechanical Behavior ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Sodium Sulfate Solution ◽  
Differential Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dimensional Variation ◽  
Complementary Techniques

ABSTRACT The residues of ornamental rocks, especially quartzite, cause great environmental impact. More impulse has been given to research on the recycling of these residues over the last years, particularly for use as aggregates in concrete and mortar. Nevertheless, the studies conducted so far do not mention the behavior of the mortar blended with aggregates coming from residues of ornamental rocks when under chemical attacks in sulfate-rich environment. Thus, in the present study it was sought to add quartzite residues to the mortar, verifying its mechanical behavior and its durability when attacked by sodium sulfate (Na2SO4). The durability of the mortar blended with quartzite residues under sulfate attack was evaluated by the dimensional variation of the test specimens when immersed in sodium sulfate solution, according to the methodology of the NBR 13583 standard. Were used the following complementary techniques: simple compressive strength, X-ray diffraction and thermogravimetric and differential analysis. From the tests, it was verified that the mortars, after attack of sodium sulfate, presented dimensional expansions superior to 0.06%, as well as increased mechanical strength. Therefore, although it was found that the specimens incorporated with quartzite residues were attacked by sulfate, it was observed that it was not able to form sufficient secondary ettringite to mechanically damage the specimens submitted to the sodium sulfate attack.

scholarly journals X-ray and Neutron Study on the Structure of Hydrous SiO2 Glass up to 10 GPa

Minerals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 84 ◽  
Author(s):  
Satoru Urakawa ◽  
Toru Inoue ◽  
Takanori Hattori ◽  
Asami Sano-Furukawa ◽  
Shinji Kohara ◽  
...  
Keyword(s):  
Oxide Glasses ◽  
Void Space ◽  
X Ray Diffraction ◽  
Amorphous Sio2 ◽  
Sio2 Glass ◽  
X Ray ◽  
X Ray Scattering ◽  
Medium Range ◽  
Two Phases ◽  
A Minor

The structure of hydrous amorphous SiO2 is fundamental in order to investigate the effects of water on the physicochemical properties of oxide glasses and magma. The hydrous SiO2 glass with 13 wt.% D2O was synthesized under high-pressure and high-temperature conditions and its structure was investigated by small angle X-ray scattering, X-ray diffraction, and neutron diffraction experiments at pressures of up to 10 GPa and room temperature. This hydrous glass is separated into two phases: a major phase rich in SiO2 and a minor phase rich in D2O molecules distributed as small domains with dimensions of less than 100 Å. Medium-range order of the hydrous glass shrinks compared to the anhydrous SiO2 glass by disruption of SiO4 linkage due to the formation of Si–OD deuterioxyl, while the response of its structure to pressure is almost the same as that of the anhydrous SiO2 glass. Most of D2O molecules are in the small domains and hardly penetrate into the void space in the ring consisting of SiO4 tetrahedra.

Sign in / Sign up

Export Citation Format

Share Document