Effect of Surface State of Die on Flow Rate of Steamed Bamboo Powder in Thermal Flow Test Using Capillary Rheometer

2015 ◽  
Vol 651-653 ◽  
pp. 830-835
Author(s):  
Shohei Kajikawa ◽  
Riku Sakagami ◽  
Takashi Iizuka
Keyword(s):  
Particle Size ◽  
Flow Rate ◽  
Surface State ◽  
Flow Behavior ◽  
Thermal Flow ◽  
Average Roughness ◽  
Arithmetic Average ◽  
Flow Test ◽  
Die Surface ◽  
Bamboo Powder

Thermal flow tests were performed on steamed bamboo powder using capillaries that were processed under different conditions in order to investigate the effect of the die surface state on the fluidity of the woody powder. The capillaries were processed by wire-cut electric discharge machining, reaming or drilling, and the arithmetic average roughness (Ra) varied from 0.5 to 2.5 μm. The bamboo powder was first steamed at 200 °C for 20 min, and its particle size was then controlled using different mesh screens. The thermal flow temperature was set at 200 °C. The results indicated that the flow behavior improved with increasing particle size. For the capillaries processed by WEDM, the flow rate for samples with particle sizes of 75~150 and 150~300 μm decreased with increasing Ra. On the other hand, when reaming or drilling was used to process the capillaries, the flow rate was almost independent of Ra, regardless of the particle size.

Proteinaceous Bubbles and Nano Particle Flows in Microchannel

2004 ◽  
Author(s):  
Jung-Yeul Jung ◽  
Ki-Taek Byun ◽  
Jae-Ho Hong ◽  
Ho-Young Kwak
Keyword(s):  
Flow Rate ◽  
Flow Behavior ◽  
Average Diameter ◽  
Scattering Method ◽  
Nano Particle ◽  
Test Results ◽  
Particle Flows ◽  
Flow Test ◽  
Before And After ◽  
Flow Through

Proteinaceous bubbles of 185 nm in average diameter were synthesized by a sonochemical treatment of bovine serum albumin in aqueous solution and the nanoparticles (TiO2) solution was made by ultrasonic irradiation. To study the macroscopic flow behavior associated with the changes in the state of microparticles, a flow test of these solutions in microchannels was done. Also the size distributions of the proteinaceous bubbles in solution before and after the flow test were measured by a light scattering method. Test results show that the air-filled proteinaceous bubbles in solution adjust their size to reduce the shear stress encountered in the flow through the microchannel. On the other hand, the flow rate of the solution with nanoparticles suspensions becomes smaller than that of deionized water above the flow rate of 6 cm3/min in the microchannel with a dimension of 100×150 μm2.

scholarly journals Effect of Heating at Oven-Dry State on Steam Treated Bamboo Powder Thermal Fluidity

2015 ◽  
Vol 2015 ◽  
pp. 1-7
Author(s):  
S. Kajikawa ◽  
T. Iizuka
Keyword(s):  
Woody Biomass ◽  
Heating Time ◽  
Thermal Flow ◽  
Capillary Rheometer ◽  
Flow Test ◽  
Thermal Changes ◽  
Dry Heating ◽  
Bamboo Powder ◽  
Increasing Temperature ◽  
Component Volatilization

In hot molding processes of woody material, it is important to understand the effect of oven-dry heating on the property of woody biomass material, such as thermal fluidity. In this study, thermal flow tests of untreated and steam treated bamboo powder were conducted to investigate the effects of heating at an oven-dry state on thermal fluidity. The test temperature was set to 200°C. Before the thermal flow test, powder was dry-heated in a capillary rheometer at 200°C with a variable heating time. Thermogravimetry was conducted to understand the thermal changes of the powder during an increasing temperature and constant temperature. Fluidity of untreated powder was improved with a short dry-heating but decreased with a long dry-heating. In contrast, steam treated powder fluidity was high compared to untreated one, but its fluidity did not improve from dry-heating. From these thermogravimetry results, the chemical changes associated with component volatilization relate with the thermal fluidity. Therefore, the decrease in fluidity from dry-heating occurred because fluidity related components escape from the powder through volatilization.

Pyrolysis of brown algae (Bifurcaria Bifurcata) in a stainless steel tubular reactor: From a review to a case study

2018 ◽  
Vol 14 (1) ◽  
pp. 31-60 ◽  
Author(s):  
M. Y. Guida ◽  
F. E. Laghchioua ◽  
A. Hannioui
Keyword(s):  
Particle Size ◽  
Stainless Steel ◽  
Flow Rate ◽  
Brown Algae ◽  
Tubular Reactor ◽  
Nitrogen Flow ◽  
Nitrogen Flow Rate ◽  
Bifurcaria Bifurcata ◽  
Bio Oil

This article deals with fast pyrolysis of brown algae, such as Bifurcaria Bifurcata at the range of temperature 300–800 °C in a stainless steel tubular reactor. After a literature review on algae and its importance in renewable sector, a case study was done on pyrolysis of brown algae especially, Bifurcaria Bifurcata. The aim was to experimentally investigate how the temperature, the particle size, the nitrogen flow rate (N2) and the heating rate affect bio-oil, bio-char and gaseous products. These parameters were varied in the ranges of 5–50 °C/min, below 0.2–1 mm and 20–200 mL. min–1, respectively. The maximum bio-oil yield of 41.3wt% was obtained at a pyrolysis temperature of 600 °C, particle size between 0.2–0.5 mm, nitrogen flow rate (N2) of 100 mL. min–1 and heating rate of 5 °C/min. Liquid product obtained under the most suitable and optimal condition was characterized by elemental analysis, 1H-NMR, FT-IR and GC-MS. The analysis of bio-oil showed that bio-oil from Bifurcaria Bifurcata could be a potential source of renewable fuel production and value added chemicals.

Utilization of Waste of Enzymes Biomass as Biosorbent for the Removal of Dyes from Aqueous Solution in Batch and Fluidized Bed Column

2020 ◽  
Vol 71 (1) ◽  
pp. 1-12
Author(s):  
Salman H. Abbas ◽  
Younis M. Younis ◽  
Mohammed K. Hussain ◽  
Firas Hashim Kamar ◽  
Gheorghe Nechifor ◽  
...  
Keyword(s):  
Experimental Data ◽  
Aqueous Solution ◽  
Particle Size ◽  
Adsorption Capacity ◽  
Fluidized Bed ◽  
Flow Rate ◽  
Fungal Biomass ◽  
Solution Flow Rate ◽  
Maximum Adsorption Capacity ◽  
Solution Flow

The biosorption performance of both batch and liquid-solid fluidized bed operations of dead fungal biomass type (Agaricusbisporus ) for removal of methylene blue from aqueous solution was investigated. In batch system, the adsorption capacity and removal efficiency of dead fungal biomass were evaluated. In fluidized bed system, the experiments were conducted to study the effects of important parameters such as particle size (701-1400�m), initial dye concentration(10-100 mg/L), bed depth (5-15 cm) and solution flow rate (5-20 ml/min) on breakthrough curves. In batch method, the experimental data was modeled using several models (Langmuir,Freundlich, Temkin and Dubinin-Radushkviechmodels) to study equilibrium isotherms, the experimental data followed Langmuir model and the results showed that the maximum adsorption capacity obtained was (28.90, 24.15, 21.23 mg/g) at mean particle size (0.786, 0.935, 1.280 mm) respectively. In Fluidized-bed method, the results show that the total ion uptake and the overall capacity will be decreased with increasing flow rate and increased with increasing initial concentrations, bed depth and decreasing particle size.

scholarly journals Effect of flow rate, particle size and modifier ratio on the supercritical fluid extraction of anthocyanins from Hibiscus sabdariffa (L).

2020 ◽  
Vol 932 ◽  
pp. 012031
Author(s):  
Zuhaili Idham ◽  
Ahmad Syahmi Zaini ◽  
Nicky Rahmana Putra ◽  
Nurfarhain Mohamed Rusli ◽  
Noor Sabariah Mahat ◽  
...  
Keyword(s):  
Particle Size ◽  
Supercritical Fluid Extraction ◽  
Supercritical Fluid ◽  
Flow Rate ◽  
Hibiscus Sabdariffa ◽  
Fluid Extraction

In Situ: A Novel Approach for the Production of Micro Holes

2010 ◽  
Vol 126-128 ◽  
pp. 885-890
Author(s):  
K.P. Somashekhar ◽  
N. Ramachandran ◽  
Jose Mathew
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
Machining Parameters ◽  
Average Roughness ◽  
Arithmetic Average ◽  
Quantitative Correlation ◽  
Good Surface ◽  
Novel Approach ◽  
Micro Holes

This work is on the preparation of microelectrodes for μ-EDM operation using μ-WEDG process. Electrodes of Ø500 μm are fabricated with various discharge energy machining conditions. Effects of gap voltage, capacitance & feed rate on the surface finish of the electrodes and overcut of the thus produced micro holes are investigated. The profile of microelectrodes is measured using surface roughness tester with 2μm stylus interfaced with SURFPAK software. The study demonstrated that for brass electrodes an arithmetic average roughness value as low as 1.7μm and an overcut of 3 µm could be achieved. The significant machining parameters are found using ANOVA. Surface of the produced microelectrodes are examined using Scanning Electron Microscope. μ-WEDG process parameters could be adjusted to achieve good surface integrity on microelectrodes. Experimental results showed that the surface roughness of microelectrodes depended primarily on feed rate of the electrode. The observations showed the clear and quantitative correlation existing between the micrometer level surface quality and process parameters. The resulting microelectrodes are found to be of exceptionally high quality and could be used for μ- EDM operation on different types of work materials.

Design and Simulation of a Hybrid Entrained-Flow and Fluidized Bed Mild Gasifier: Part 2—Case Study and Analysis

2011 ◽  
Author(s):  
A. K. M. Monayem Mazumder ◽  
Ting Wang ◽  
Jobaidur R. Khan
Keyword(s):  
Multiphase Flow ◽  
Fluidized Bed ◽  
Flow Behavior ◽  
Flame Temperature ◽  
Heterogeneous Reactions ◽  
Thermal Flow ◽  
Entrained Flow ◽  
Progressive Development ◽  
Gasification Process ◽  
Flow And Heat Transfer

To help design a mild-gasifier, a reactive multiphase flow computational model has been developed in Part 1 using Eulerian-Eulerian method to investigate the thermal-flow and gasification process inside a conceptual, hybrid entrained-flow and fluidized-bed mild-gasifier. In Part 2, the results of the verifications and the progressive development from simple conditions without particles and reactions to complicated conditions with full reactive multiphase flow are presented. Development of the model starts from simulating single-phase turbulent flow and heat transfer in order to understand the thermal-flow behavior, followed by introducing seven global, homogeneous gasification reactions progressively added one equation at a time. Finally, the particles are introduced, and heterogeneous reactions are added in a granular flow field. The mass-weighted, adiabatic flame temperature is validated through theoretical calculation and the minimum fluidization velocity is found to be close to Ergun’s correlation. Furthermore, the predicted exit species composition is consistent with the equilibrium values.

Effect of Outer Fin Axial Gap on the Sealing Effectiveness and Fluid Dynamics of Radial Rim Seal

2017 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Liming Song ◽  
Qing Gao ◽  
Xin Yan ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Flow Rate ◽  
Gas Turbines ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Coolant Flow ◽  
Coolant Flow Rate ◽  
Navier Stokes ◽  
Hot Gas

The modern gas turbine is widely applied in the aviation propulsion and power generation. The rim seal is usually designed at the periphery of the wheel-space and prevented the hot gas ingestion in modern gas turbines. The high sealing effectiveness of rim seal can improve the aerodynamic performance of gas turbines and avoid of the disc overheating. Effect of outer fin axial gap of radial rim seal on the sealing effectiveness and fluid dynamics was numerically investigated in this work. The sealing effectiveness and fluid dynamics of radial rim seal with three different outer fin axial gaps was conducted at different coolant flow rates using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) and SST turbulent model solutions. The accuracy of the presented numerical approach for the prediction of the sealing performance of the turbine rim seal was demonstrated. The obtained results show that the sealing effectiveness of radial rim seal increases with increase of coolant flow rate at the fixed axial outer fin gap. The sealing effectiveness increases with decrease of the axial outer fin gap at the fixed coolant flow rate. Furthermore, at the fixed coolant flow rate, the hot gas ingestion increases with the increase of the axial outer fin gap. This flow behavior intensifies the interaction between the hot gas and coolant flow at the clearance of radial rim seal. The preswirl coefficient in the wheel-space cavity is also illustrated to analyze the flow dynamics of radial rim seal at different axial outer fin gaps.

scholarly journals Effect of the Flame Dome Depth and Improvement of the Pressure Loss in the Dump Diffuser

1998 ◽  
Author(s):  
Shinji Honami ◽  
Wataru Tsuboi ◽  
Takaaki Shizawa
Keyword(s):  
Velocity Profile ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Pressure Loss ◽  
Total Pressure ◽  
Flow Behavior ◽  
Sudden Expansion ◽  
Mean Velocity ◽  
The Mean ◽  
Stress Profiles

This paper presents the effect of flame dome depth on the total pressure performance and flow behavior in a sudden expansion region of the combustor diffuser without flow entering the dome head. The mean velocity and turbulent Reynolds stress profiles in the sudden expansion region were measured by a Laser Doppler Velocitmetry (LDV) system. The experiments show that total pressure loss is increased, when flame dome depth is increased. Installation of an inclined combuster wall in the sudden expansion region is suggested from the viewpoint of a control of the reattaching flow. The inclined combustor wall is found to be effective in improvement of the diffuser performance. Better characteristics of the flow rate distribution into the branched channels are obtained in the inclined wall configuration, even if the distorted velocity profile is provided at the diffuser inlet.

Sign in / Sign up

Export Citation Format

Share Document