Microstructure and Mechanical Properties of TiB2/Al-Si Composites Fabricated by Electron Beam Rapid Manufacture

2021 ◽  
Vol 1035 ◽  
pp. 884-891
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Xian Feng Li ◽  
Hao Wei Wang ◽  
Nan Liao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Electron Beam ◽  
Grain Boundary ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size ◽  
Before And After ◽  
Rapid Manufacture ◽  
Equiaxed Grains

Bulky sample was fabricated by electron beam rapid manufacture (EBRM) technology, in which Ф1.6 mm wire of in-situ TiB2/Al-Si compositeswas selected as deposition metal, following byT6 heat treatment. The microstructure and mechanical properties of the bulky sample before and afterheat treatment were analyzed. Experimental results showed that the microstructure parallel to the weld was similar to that perpendicular to the weld. The microstructure of the as-deposited sample consisted of columnar and equiaxed grains, in which siliconwas distributed along the grain boundary and the grain size was about 30 μm. Besides, some TiB2 particles converged at the grain boundary. After T6 heat treatment, the average grain size of the sample increasedobviously.The average hardness of the sample was increased to 114.65 HV from 46.55 HV, an increase of 146%. The tensile strength of the sample increased to 326.66MPafrom 143.97 MPa, but the elongationdecreased compared with that of the as-deposited state. The tensile test showed that the mechanical properties of TiB2/Al-Si composites formed by electron beam rapid manufacture were isotropic before and after heat treatment.

Influence of Annealing on the Microstructure and Mechanical Properties of Electrodeposited Nanocrystalline Nickel

2011 ◽  
Vol 683 ◽  
pp. 103-112 ◽  
Author(s):  
B. Yang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elastic Modulus ◽  
Grain Boundary ◽  
Boundary Structure ◽  
Boundary State ◽  
Microstructure And Mechanical Properties ◽  
Grain Boundary Structure ◽  
Average Grain Size ◽  
Different Grain Size

The evolution of the microstructure and mechanical properties of electrodeposited nanocrystalline Ni with different annealing procedures was studied systematically. For the annealed specimens hardness decreases with increasing average grain size but the dependence changes at different grain size ranges. The specimens annealed at a low temperature show higher hardness compared to the as-deposited nanocrystalline Ni, despite an increased measured average grain size. In association with this hardening an increase in elastic modulus and a decrease in microstrain was observed after annealing. With increasing annealing temperature both the tensile strength and the fracture strain were observed to decrease, this is companied with a transition from ductile to brittle in the fracture surfaces. These results indicated that the mechanical behaviour of nanocrystalline Ni depends not only on the average grain size but also on the grain boundary structure. A change in the grain boundary state arising from annealing may be responsible for the observed increase in hardness and elastic modulus as well as the deterioration of tensile properties.

Synergetic Effect of ECAP and Friction Stir Welding on Microstructure and Mechanical Properties of Aluminium Sheets

2010 ◽  
Vol 667-669 ◽  
pp. 505-510
Author(s):  
Ilya Nikulin ◽  
Alla Kipelova ◽  
Sergey Malopheyev ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Friction Stir Welding ◽  
Base Metal ◽  
Synergetic Effect ◽  
Aluminum Matrix ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

Friction stir welding (FSW) was used to join the submicrocrystalline (SMC) grained Al-Cu-Mg-Ag sheets produced by equal channel angular pressing (ECAP) followed by hot rolling (HR). The effect of SPD and FSW on the microstructure and mechanical properties in the zone of base metal, as well as in the stirred zone (SZ) were examined. In addition, effect of standard heat treatment on microstructure and mechanical properties in these zones was considered. A refined microstructure with an average grain size of ~ 0.6 m and a portion of high-angle grain boundaries (HAGBs) of ~0.67 was produced in sheets by ECAP followed by HR at 250°C. The microcrystalline grained structure with average grain size of ~2.3 mm was found in joint weld. The moderate mechanical properties were revealed in SMC sheets and joint welds. Heat treatment considerably increases strength of the base metal as well as the joint welds. The higher strength of the alloy after T6 temper is attributed to the dense precipitations of  dispersoids having plate-like shape which are uniformly distributed within aluminum matrix. It was observed that FSW can produce full strength weld both in the tempered and in the un-tempered conditions.

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by SLM

2015 ◽  
Vol 651-653 ◽  
pp. 677-682 ◽  
Author(s):  
Anatoliy Popovich ◽  
Vadim Sufiiarov ◽  
Evgenii Borisov ◽  
Igor Polozov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Mechanical Behavior ◽  
Ductile Fracture ◽  
Elevated Temperatures ◽  
Initial Material ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Before And After

The article presents results of a study of phase composition and microstructure of initial material and samples obtained by selective laser melting of titanium-based alloy, as well as samples after heat treatment. The effect of heat treatment on microstructure and mechanical properties of specimens was shown. It was studied mechanical behavior of manufactured specimens before and after heat treatment at room and elevated temperatures as well. The heat treatment allows obtaining sufficient mechanical properties of material at room and elevated temperatures such as increase in ductility of material. The fractography of samples showed that they feature ductile fracture with brittle elements.

Effect of Post Weld Heat Treatment on Fusion and Heat Affected Zone Microstructure and Mechanical Properties of Inconel X-750 Welds

2011 ◽  
Vol 214 ◽  
pp. 108-112 ◽  
Author(s):  
Prachya Peasura ◽  
Bovornchok Poopat
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Grain Boundary ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Aging Temperature ◽  
Post Weld Heat Treatment ◽  
High Aging Temperature ◽  
Zone Microstructure

The Inconel X-750 indicates good hot corrosion resistance, high stability and strength at high temperatures and for this reason the alloy is used in manufacturing of gas turbine hot components. The objective of this research was study the effect of post weld heat treatment (PWHT) on fusion zone and heat affected zone microstructure and mechanical properties of Inconel X-750 weld. After welding, samples were solutionized at 1500 0C. Various aging temperature and times were studied. The results show that aging temperature and time during PWHT can greatly affect microstructure and hardness in fusion zone and heat affected zone. As high aging temperature was used, the grain size also increased and M23C6 at the grain boundary decreased. This can result in decreased of hardness. Moreover excessive aging temperature can result in increasing MC carbide intensity in parent phase (austenite). It can also be observed that M23C6 at the grain boundary decreased due to high aging temperature. This resulted in decreasing of hardness of weld metal and heat affected zone. Experimental results showed that the aging temperature 705 0C aging time of 24 hours provided smaller grain size, suitable size and intensity of MC carbide resulting in higher hardness both in weld metal and HAZ.

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

2019 ◽  
Vol 944 ◽  
pp. 64-72
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Ya Qi Deng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
Filler Wire ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Before And After

Bulky sample was made by using TIG wire and arc additive manufacturing (WAAM) technology, in which Ф1.6 mm filler wire of in-situ TiB2/Al-Si composites was selected as deposition metal, following by T6 heat treatment. The microstructure and mechanical properties of the bulky sample before and after heat treatment were analyzed. Experimental results showed that the texture of the original samples parallel to the weld direction and perpendicular to the weld direction was similar consisting of columnar dendrites and equiaxed crystals. After T6 heat treatment, the hardness of the sample was increased to 115.85 HV from 62.83 HV, the yield strength of the sample was 273.33 MPa, the average tensile strength was 347.33 MPa, and the average elongation after fracture was 7.96%. Although pore defects existed in the fracture, yet the fracture of the sample was ductile fracture.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

Effect of post-heat treatment cooling on microstructure and mechanical properties of selective laser melting manufactured austenitic 316L stainless steel

2020 ◽  
Vol 26 (10) ◽  
pp. 1739-1749
Author(s):  
Saad Waqar ◽  
Jiangwei Liu ◽  
Qidong Sun ◽  
Kai Guo ◽  
Jie Sun
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
Content Type ◽  
Post Annealing ◽  
Cooling Conditions ◽  
Microstructure And Mechanical Properties ◽  
Heat Treated

Purpose This paper aims to investigate the influence of different post-annealing cooling conditions, i.e. furnace cooling (heat treatment (HT) 1 – slow cooling) and air cooling (HT 2 – fast cooling), on the microstructure and mechanical properties of selective laser melting (SLM) built austenitic 316L stainless steel (SS). Design/methodology/approach Three sets of 316L SS samples were fabricated using a machine standard scanning strategy. Each set consists of three tensile samples and a cubic sample for microstructural investigations. Two sets were subsequently subjected to annealing HT with different cooling conditions, i.e. HT 1 and HT 2, whereas one set was used in the as-built (AB) condition. The standard metallographic techniques of X-ray diffraction, scanning electron microscopy and electron back-scattered diffraction were used to investigate the microstructural variations induced by different cooling conditions. The resultant changes in mechanical properties were also investigated. Findings The phase change of SLM fabricated 316L was observed to be independent of the investigated cooling conditions and all samples consist of austenite phase only. Both HT 1 and HT 2 lead to dissolved characteristic melt pools of SLM. Noticeable increase in grain size of HT 1 and HT 2 samples was also observed. Compared with AB samples, the grain size of HT 1 and HT 2 was increased by 12.5% and 50%, respectively. A decreased hardness and strength, along with an increased ductility was also observed for HT 2 samples compared with HT 1 and AB samples. Originality/value From previous studies, it has been noticed that most investigations on HT of SLM fabricated 316L were mainly focused on the HT temperature or holding time. However, the post-HT cooling rate is also an equally important factor in deciding the microstructure and mechanical properties of heat-treated components. Therefore, this paper investigates the influence of different post-annealing cooling conditions on microstructure and mechanical properties of SLM fabricated 316L components. This study provides a foundation for considering the post-HT cooling rate as an influential parameter that controls the properties of heat-treated SLM components.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

Effect of Bi on Microstructure and Mechanical Properties of Extruded AZ80-2Sn Magnesium Alloy

2018 ◽  
Vol 37 (1) ◽  
pp. 97-103 ◽  
Author(s):  
Hansong Xue ◽  
Xinyu Li ◽  
Weina Zhang ◽  
Zhihui Xing ◽  
Jinsong Rao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

AbstractThe effects of Bi on the microstructure and mechanical properties of AZ80-2Sn alloy were investigated. The results show that the addition of Bi within the as-cast AZ80-2Sn alloy promotes the formation of Mg3Bi2 phase, which can refine the grains and make the eutectic phases discontinuous. The addition of 0.5 % Bi within the as-extruded AZ80-2Sn alloy, the average grain size decreases to 12 μm and the fine granular Mg17Al12 and Mg3Bi2 phases are dispersed in the α-Mg matrix. With an increase in Bi content, the Mg17Al12 and Mg3Bi2 phases become coarsened and the grain size increases. The as-extruded AZ80-2Sn-0.5 %Bi alloy has the optimal properties, and the ultimate tensile strength, yield strength and elongation are 379.6 MPa, 247.1 MPa and 14.8 %, respectively.

Investigation of Microstructure and Mechanical Properties of Friction Stir Lap Jointed Ni Base Superalloy

2012 ◽  
Vol 724 ◽  
pp. 481-485
Author(s):  
Kuk Hyun Song ◽  
Kazuhiro Nakata
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Friction Stir Welding ◽  
Base Material ◽  
Lap Joints ◽  
Stir Zone ◽  
Inconel 600 ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

This study evaluated the microstructure and mechanical properties of friction stir welded lap joints. Inconel 600 and SS 400 as experimental materials were selected, and friction stir welding was carried out at tool rotation speed of 200 rpm and welding speed of 100 mm/min. Applying the friction stir welding was notably effective to reduce the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. Joint interface between Inconel 600 and SS 400 showed a sound weld without voids and cracks. Also, the hook, along the Inconel 600 alloy from SS 400, was formed at advancing side, which directly affected an increase in peel strength. In this study, we systematically discussed the evolution on microstructure and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.

Sign in / Sign up

Export Citation Format

Share Document